<- RFC Index (2001..2100)
RFC 2086
Obsoleted by RFC 4314
Network Working Group J. Myers
Request for Comments: 2086 Carnegie Mellon
Category: Standards Track January 1997
IMAP4 ACL extension
Status of this Memo
This document specifies an Internet standards track protocol for the
Internet community, and requests discussion and suggestions for
improvements. Please refer to the current edition of the "Internet
Official Protocol Standards" (STD 1) for the standardization state
and status of this protocol. Distribution of this memo is unlimited.
1. Abstract
The ACL extension of the Internet Message Access Protocol [IMAP4]
permits access control lists to be manipulated through the IMAP
protocol.
Table of Contents
1. Abstract............................................... 1
2. Conventions Used in this Document...................... 1
3. Introduction and Overview.............................. 2
4. Commands............................................... 3
4.1. SETACL................................................. 3
4.2. DELETEACL.............................................. 4
4.3. GETACL................................................. 4
4.4. LISTRIGHTS............................................. 4
4.5. MYRIGHTS............................................... 5
5. Responses.............................................. 5
5.1. ACL.................................................... 5
5.2. LISTRIGHTS............................................. 6
5.3. MYRIGHTS............................................... 6
6. Formal Syntax.......................................... 6
7. References............................................. 7
8. Security Considerations................................ 7
9. Author's Address....................................... 8
2. Conventions Used in this Document
In examples, "C:" and "S:" indicate lines sent by the client and
server respectively.
Myers Standards Track [Page 1]
RFC 2086 ACL extension January 1997
3. Introduction and Overview
The ACL extension is present in any IMAP4 implementation which
returns "ACL" as one of the supported capabilities to the CAPABILITY
command.
An access control list is a set of <identifier,rights> pairs.
Identifier is a US-ASCII string. The identifier anyone is reserved
to refer to the universal identity (all authentications, including
anonymous). All user name strings accepted by the LOGIN or
AUTHENTICATE commands to authenticate to the IMAP server are reserved
as identifiers for the corresponding user. Identifiers starting with
a dash ("-") are reserved for "negative rights", described below.
All other identifier strings are interpreted in an implementation-
defined manner.
Rights is a string listing a (possibly empty) set of alphanumeric
characters, each character listing a set of operations which is being
controlled. Letters are reserved for ``standard'' rights, listed
below. The set of standard rights may only be extended by a
standards-track document. Digits are reserved for implementation or
site defined rights. The currently defined standard rights are:
l - lookup (mailbox is visible to LIST/LSUB commands)
r - read (SELECT the mailbox, perform CHECK, FETCH, PARTIAL,
SEARCH, COPY from mailbox)
s - keep seen/unseen information across sessions (STORE SEEN flag)
w - write (STORE flags other than SEEN and DELETED)
i - insert (perform APPEND, COPY into mailbox)
p - post (send mail to submission address for mailbox,
not enforced by IMAP4 itself)
c - create (CREATE new sub-mailboxes in any implementation-defined
hierarchy)
d - delete (STORE DELETED flag, perform EXPUNGE)
a - administer (perform SETACL)
An implementation may tie rights together or may force rights to
always or never be granted to particular identifiers. For example,
in an implementation that uses unix mode bits, the rights "wisd" are
tied, the "a" right is always granted to the owner of a mailbox and
is never granted to another user. If rights are tied in an
implementation, the implementation must be conservative in granting
rights in response to SETACL commands--unless all rights in a tied
set are specified, none of that set should be included in the ACL
entry for that identifier. A client may discover the set of rights
which may be granted to a given identifier in the ACL for a given
mailbox by using the LISTRIGHTS command.
Myers Standards Track [Page 2]
RFC 2086 ACL extension January 1997
It is possible for multiple identifiers in an access control list to
apply to a given user (or other authentication identity). For
example, an ACL may include rights to be granted to the identifier
matching the user, one or more implementation-defined identifiers
matching groups which include the user, and/or the identifier
"anyone". How these rights are combined to determine the user's
access is implementation-defined. An implementation may choose, for
example, to use the union of the rights granted to the applicable
identifiers. An implementation may instead choose, for example, to
only use those rights granted to the most specific identifier present
in the ACL. A client may determine the set of rights granted to the
logged-in user for a given mailbox by using the MYRIGHTS command.
When an identifier in an ACL starts with a dash ("-"), that indicates
that associated rights are to be removed from the identifier that is
prefixed by the dash. For example, if the identifier "-fred" is
granted the "w" right, that indicates that the "w" right is to be
removed from users matching the identifier "fred". Implementations
need not support having identifiers which start with a dash in ACLs.
4. Commands
4.1. SETACL
Arguments: mailbox name
authentication identifier
access right modification
Data: no specific data for this command
Result: OK - setacl completed
NO - setacl failure: can't set acl
BAD - command unknown or arguments invalid
The SETACL command changes the access control list on the
specified mailbox so that the specified identifier is granted
permissions as specified in the third argument.
The third argument is a string containing an optional plus ("+")
or minus ("-") prefix, followed by zero or more rights characters.
If the string starts with a plus, the following rights are added
to any existing rights for the identifier. If the string starts
with a minus, the following rights are removed from any existing
rights for the identifier. If the string does not start with a
plus or minus, the rights replace any existing rights for the
identifier.
Myers Standards Track [Page 3]
RFC 2086 ACL extension January 1997
4.2. DELETEACL
Arguments: mailbox name
authentication identifier
Data: no specific data for this command
Result: OK - deleteacl completed
NO - deleteacl failure: can't delete acl
BAD - command unknown or arguments invalid
The DELETEACL command removes any <identifier,rights> pair for the
specified identifier from the access control list for the specified
mailbox.
4.3. GETACL
Arguments: mailbox name
Data: untagged responses: ACL
Result: OK - getacl completed
NO - getacl failure: can't get acl
BAD - command unknown or arguments invalid
The GETACL command returns the access control list for mailbox in
an untagged ACL reply.
Example: C: A002 GETACL INBOX
S: * ACL INBOX Fred rwipslda
S: A002 OK Getacl complete
4.4. LISTRIGHTS
Arguments: mailbox name
authentication identifier
Data: untagged responses: LISTRIGHTS
Result: OK - listrights completed
NO - listrights failure: can't get rights list
BAD - command unknown or arguments invalid
The LISTRIGHTS command takes a mailbox name and an identifier and
returns information about what rights may be granted to the identifier
in the ACL for the mailbox.
Myers Standards Track [Page 4]
RFC 2086 ACL extension January 1997
Example: C: a001 LISTRIGHTS ~/Mail/saved smith
S: * LISTRIGHTS ~/Mail/saved smith la r swicd
S: a001 OK Listrights completed
C: a005 LISTRIGHTS archive.imap anyone
S: * LISTRIGHTS archive.imap anyone "" l r s w i p c d a
0 1 2 3 4 5 6 7 8 9
4.5. MYRIGHTS
Arguments: mailbox name
Data: untagged responses: MYRIGHTS
Result: OK - myrights completed
NO - myrights failure: can't get rights
BAD - command unknown or arguments invalid
The MYRIGHTS command returns the set of rights that the user has
to mailbox in an untagged MYRIGHTS reply.
Example: C: A003 MYRIGHTS INBOX
S: * MYRIGHTS INBOX rwipslda
S: A003 OK Myrights complete
5. Responses
5.1. ACL
Data: mailbox name
zero or more identifier rights pairs
The ACL response occurs as a result of a GETACL command. The first
string is the mailbox name for which this ACL applies. This is
followed by zero or more pairs of strings, each pair contains the
identifier for which the entry applies followed by the set of
rights that the identifier has.
Myers Standards Track [Page 5]
RFC 2086 ACL extension January 1997
5.2. LISTRIGHTS
Data: mailbox name
identifier
required rights
list of optional rights
The LISTRIGHTS response occurs as a result of a LISTRIGHTS
command. The first two strings are the mailbox name and identifier
for which this rights list applies. Following the identifier is a
string containing the (possibly empty) set of rights the
identifier will always be granted in the mailbox.
Following this are zero or more strings each containing a set of
rights the identifier may be granted in the mailbox. Rights
mentioned in the same string are tied together--either all must be
granted to the identifier in the mailbox or none may be granted.
The same right may not be listed more than once in the LISTRIGHTS
command.
5.3. MYRIGHTS
Data: mailbox name
rights
The MYRIGHTS response occurs as a result of a MYRIGHTS command.
The first string is the mailbox name for which these rights apply.
The second string is the set of rights that the client has.
6. Formal Syntax
The following syntax specification uses the augmented Backus-Naur
Form (BNF) notation as specified in [RFC-822] as modified by [IMAP4].
Non-terminals referenced but not defined below are as defined by
[IMAP4].
Except as noted otherwise, all alphabetic characters are case-
insensitive. The use of upper or lower case characters to define
token strings is for editorial clarity only. Implementations MUST
accept these strings in a case-insensitive fashion.
Myers Standards Track [Page 6]
RFC 2086 ACL extension January 1997
acl_data ::= "ACL" SPACE mailbox *(SPACE identifier SPACE
rights)
deleteacl ::= "DELETEACL" SPACE mailbox SPACE identifier
getacl ::= "GETACL" SPACE mailbox
identifier ::= astring
listrights ::= "LISTRIGHTS" SPACE mailbox SPACE identifier
listrights_data ::= "LISTRIGHTS" SPACE mailbox SPACE identifier
SPACE rights *(SPACE rights)
mod_rights ::= astring
;; +rights to add, -rights to remove
;; rights to replace
myrights ::= "MYRIGHTS" SPACE mailbox
myrights_data ::= "MYRIGHTS" SPACE mailbox SPACE rights
rights ::= astring
setacl ::= "SETACL" SPACE mailbox SPACE identifier
SPACE mod_rights
7. References
[IMAP4] Crispin, M., "Internet Message Access Protocol - Version 4",
RFC 1730, University of Washington, December 1994.
[RFC-822] Crocker, D., "Standard for the Format of ARPA Internet Text
Messages", STD 11, RFC 822.
8. Security Considerations
An implementation must make sure the ACL commands themselves do not
give information about mailboxes with appropriately restricted ACL's.
For example, a GETACL command on a mailbox for which the user has
insufficient rights should not admit the mailbox exists, much less
return the mailbox's ACL.
Myers Standards Track [Page 7]
RFC 2086 ACL extension January 1997
9. Author's Address
John G. Myers
Carnegie-Mellon University
5000 Forbes Ave.
Pittsburgh PA, 15213-3890
Email: jgm+@cmu.edu
Myers Standards Track [Page 8]