<- RFC Index (4801..4900)
RFC 4803
Network Working Group T. Nadeau, Ed.
Request for Comment: 4803 Cisco Systems, Inc.
Category: Standards Track A. Farrel, Ed.
Old Dog Consulting
February 2007
Generalized Multiprotocol Label Switching (GMPLS)
Label Switching Router (LSR) Management Information Base
Status of This Memo
This document specifies an Internet standards track protocol for the
Internet community, and requests discussion and suggestions for
improvements. Please refer to the current edition of the "Internet
Official Protocol Standards" (STD 1) for the standardization state
and status of this protocol. Distribution of this memo is unlimited.
Copyright Notice
Copyright (C) The IETF Trust (2007).
Abstract
This memo defines a portion of the Management Information Base (MIB)
for use with network management protocols in the Internet community.
In particular, it describes managed objects to configure and/or
monitor a Generalized Multiprotocol Label Switching (GMPLS) Label
Switching Router (LSR).
Nadeau & Farrel Standards Track [Page 1]
RFC 4803 GMPLS LSR MIB February 2007
Table of Contents
1. Introduction ....................................................2
1.1. Migration Strategy .........................................2
2. Terminology .....................................................3
3. The Internet-Standard Management Framework ......................4
4. Outline .........................................................5
4.1. MIB Modules ................................................5
4.1.1. Summary of the GMPLS-LSR-STD-MIB Module .............5
4.1.2. Summary of the GMPLS-LABEL-STD-MIB Module ...........5
4.2. Configuring Statically Provisioned LSPs ....................5
5. Bidirectional LSPs ..............................................6
6. Example of LSP Setup ............................................7
7. GMPLS Label Switching Router MIB Definitions ...................11
8. GMPLS Label MIB Definitions ....................................22
9. Security Considerations ........................................36
10. Acknowledgments ...............................................37
11. IANA Considerations ...........................................38
12. References ....................................................38
12.1. Normative References .....................................38
12.2. Informative References ...................................40
1. Introduction
This memo defines a portion of the Management Information Base (MIB)
for use with network management protocols in the Internet community.
In particular, it describes managed objects for modeling a
Generalized Multiprotocol Label Switching (GMPLS) [RFC3945] Label
Switching Router (LSR).
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in BCP 14, RFC 2119
[RFC2119].
1.1. Migration Strategy
MPLS LSRs may be modeled and managed using the MPLS-LSR-STD-MIB
module [RFC3813].
LSRs may be migrated to be modeled and managed using the MIB modules
in this document in order to migrate the LSRs to GMPLS support, or to
take advantage of additional MIB objects defined in these MIB modules
that are applicable to MPLS-TE.
Nadeau & Farrel Standards Track [Page 2]
RFC 4803 GMPLS LSR MIB February 2007
The GMPLS LSR MIB module (GMPLS-LSR-STD-MIB), defined in this
document, extends the MPLS-LSR-STD-MIB module [RFC3813] through a
series of sparse augmentations of the MIB tables. The only additions
are for support of GMPLS or to support the increased complexity of
MPLS and GMPLS systems.
In order to migrate from MPLS-LSR-STD-MIB support to GMPLS-LSR-STD-
MIB support, an implementation needs only to add support for the
additional tables and objects defined in GMPLS-LSR-STD-MIB. The
gmplsInterfaceSignalingCaps object allows an implementation to use
the objects and tables of GMPLS-LSR-STD-MIB without supporting the
GMPLS protocols.
The GMPLS Label MIB module (GMPLS-LABEL-STD-MIB), also defined in
this document, allows labels to be configured and examined, and it
supports more varieties of labels as appropriate for GMPLS. Labels
may be referenced using a row pointer from objects within the GMPLS-
LSR-STD-MIB module. MPLS implementations (MPLS-LSR-STD-MIB) may also
reference labels held in the GMPLS-LABEL-STD-MIB module through the
various label pointer objects in the MPLS-LSR-STD-MIB module (such as
mplsInSegmentLabelPtr), and may do so without implementing the
GMPLS-LSR-STD-MIB module.
The companion document modeling and managing GMPLS-based traffic
engineering [RFC4802] extends the MPLS-TE-STD-MIB module [RFC3812]
with the same intentions.
Textual conventions are defined in [RFC4801], which extends the set
of textual conventions originally defined in [RFC3811].
2. Terminology
This document uses terminology from the document describing the MPLS
architecture [RFC3031] and the GMPLS architecture [RFC3945].
A Label Switched Path (LSP) is modeled as a connection consisting of
one or more incoming segments (in-segments) and/or one or more
outgoing segments (out-segments) at an LSR. The association or
interconnection of the in-segments and out-segments is accomplished
by using a cross-connect. We use the terminology "connection" and
"LSP" interchangeably where the meaning is clear from the context.
in-segment This is analogous to a GMPLS Label on an interface.
out-segment This is analogous to a GMPLS Label on an interface.
Nadeau & Farrel Standards Track [Page 3]
RFC 4803 GMPLS LSR MIB February 2007
cross-connect This describes the conceptual connection between a set
of in-segments and out-segments. Note that either set
may be empty; for example, a cross-connect may connect
only out-segments together with no in-segments in the
case where an LSP originates on an LSR.
The terms 'ingress' and 'head-end' (or 'head') are used in this
document to indicate the signaling source of an LSP. This is
sometimes also referred to as the 'sender'.
The terms 'egress' and 'tail-end' (or 'tail') are used in this
document to indicate the signaling destination of an LSP.
The term 'upstream' is used in this document to refer to the part of
an LSP that is closer to the ingress than the current point of
reference.
The term 'downstream' is used in this document to refer to the part
of an LSP that is closer to the egress than the current point of
reference.
The term 'forward' is used in this document to indicate the direction
of data flow from the ingress toward the egress.
The term 'reverse' is used in this document to indicate the direction
of data flow from the egress toward the ingress.
3. The Internet-Standard Management Framework
For a detailed overview of the documents that describe the current
Internet-Standard Management Framework, please refer to section 7 of
RFC 3410 [RFC3410].
Managed objects are accessed via a virtual information store, termed
the Management Information Base or MIB. MIB objects are generally
accessed through the Simple Network Management Protocol (SNMP).
Objects in the MIB are defined using the mechanisms defined in the
Structure of Management Information (SMI). This memo specifies a MIB
module that is compliant to the SMIv2, which is described in STD 58,
RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC 2580
[RFC2580].
Nadeau & Farrel Standards Track [Page 4]
RFC 4803 GMPLS LSR MIB February 2007
4. Outline
4.1. MIB Modules
There are two MIB modules defined in this document.
The GMPLS-LSR-STD-MIB module contains tables that sparse augment
tables defined in the MPLS-LSR-STD-MIB module [RFC3813]. This MIB
module is used in conjunction with the MPLS-LSR-STD-MIB module
[RFC3813] in systems that support GMPLS.
The GMPLS-LABEL-STD-MIB module contains objects for managing GMPLS
Labels when they cannot be represented using the textual conventions
of the MPLS-TC-STD-MIB module [RFC3811], or when more detailed access
to the sub-fields of the labels is required.
4.1.1. Summary of the GMPLS-LSR-STD-MIB Module
The MIB tables in the GMPLS-LSR-STD-MIB module are as follows:
- The interface configuration table (gmplsInterfaceTable) sparse
augments the mplsInterfaceTable [RFC3813] to enable the GMPLS
protocol on MPLS-capable interfaces.
- The in-segment (gmplsInSegmentTable) and out-segment
(gmplsOutSegmentTable) tables sparse augment mplsInSegmentTable
and mplsOutSegmentTable [RFC3813] to enable configuration of
GMPLS-specific parameters for LSP segments at an LSR.
These tables are described in the subsequent sections.
4.1.2. Summary of the GMPLS-LABEL-STD-MIB Module
There is one MIB table in the GMPLS-LABEL-STD-MIB module as follows:
- The gmplsLabelTable allows Generalized Labels to be defined and
managed in a central location. Generalized Labels can be of
variable length and have distinct bit-by-bit interpretations
depending upon how they are defined for the specific technology in
which they are used. For example, labels used for MPLS packet
switching are different in length and content from labels used in
Time Division Multiplexer (TDM) timeslot switching.
4.2. Configuring Statically Provisioned LSPs
Configuring statically provisioned GMPLS LSPs through an LSR involves
the following steps:
Nadeau & Farrel Standards Track [Page 5]
RFC 4803 GMPLS LSR MIB February 2007
- Configuring an interface using the MPLS-LSR-STD-MIB module
[RFC3813].
- Enabling GMPLS on GMPLS-capable interfaces using the GMPLS-LSR-
STD-MIB module in this document.
- Configuring in-segments and out-segments using the MPLS-LSR-STD-
MIB module [RFC3813].
- Configuring GMPLS extensions to the in-segments and out-segments
using the GMPLS-LSR-STD-MIB module in this document.
- Setting up the cross-connect table in the MPLS-LSR-STD-MIB module
[RFC3813] to associate segments and/or to indicate connection
origination and termination.
- Optionally setting up labels in the label table in the GMPLS-
LABEL-STD-MIB module in this document if the textual convention
MplsLabel [RFC3811] is not capable of holding the required label
(for example, if the label requires more than 32 bits to encode
it), or if the operator wishes to disambiguate GMPLS Label types.
- Optionally specifying label stack actions in the MPLS-LSR-STD-MIB
module [RFC3813].
- Optionally specifying segment traffic parameters in the MPLS-LSR-
STD-MIB module [RFC3813].
5. Bidirectional LSPs
The GMPLS-LSR-STD-MIB module supports bidirectional LSPs as required
for GMPLS. A single value of mplsXCIndex is shared by all of the
segments for the entire bidirectional LSP. This facilitates a simple
reference from [RFC3812] and [RFC4802] and makes fate-sharing more
obvious.
It is, however, important that the direction of segments is
understood to avoid connecting all in-segments to all out-segments.
This is achieved by an object in each segment that indicates the
direction of the segment with respect to data flow.
A segment that is marked as 'forward' carries data from the 'head' of
the LSP to the 'tail'. A segment marked as 'reverse' carries data in
the reverse direction.
Nadeau & Farrel Standards Track [Page 6]
RFC 4803 GMPLS LSR MIB February 2007
Where an LSP is signaled using a conventional signaling protocol, the
'head' of the LSP is the source of the signaling (also known as the
ingress) and the 'tail' is the destination (also known as the
egress). For manually configured LSPs, an arbitrary decision must be
made about which segments are 'forward' and which 'reverse'. For
consistency, this decision should be made across all LSRs that
participate in the LSP by assigning 'head' and 'tail' ends to the
LSP.
6. Example of LSP Setup
In this section, we provide a brief example of using the MIB objects
described in sections 7 and 8 to set up an LSP. While this example
is not meant to illustrate every nuance of the MIB modules, it is
intended as an aid to understanding some of the key concepts. It is
meant to be read after going through the MIB modules themselves. A
prerequisite is an understanding of the MPLS-LSR-STD-MIB module
[RFC3813].
Suppose that one would like to manually create a best-effort,
bidirectional LSP. Assume that, in the forward direction, the LSP
enters the LSR via MPLS interface A with ifIndex 12 and exits the LSR
via MPLS interface B with ifIndex 13. For the reverse direction, we
assume that the LSP enters via interface B and leaves via interface A
(i.e., the forward and reverse directions use the same bidirectional
interfaces). Let us also assume that we do not wish to have a label
stack beneath the top label on the outgoing labeled packets. The
following example illustrates which rows and corresponding objects
might be created to accomplish this.
We must first create rows in the gmplsLabelTable corresponding to the
labels required for each of the forward- and reverse-direction in-
and out-segments. For the purpose of this example, the forward and
reverse labels on each interface will be the same, hence we need to
create just two rows in the gmplsLabelTable - one for each interface.
In gmplsLabelTable:
{
gmplsLabelInterface = 12,
gmplsLabelIndex = 1,
gmplsLabelSubindex = 0,
gmplsLabelType = gmplsFreeformLabel(3),
gmplsLabelFreeform = 0x123456789ABCDEF0
gmplsLabelRowStatus = createAndGo(4)
}
Nadeau & Farrel Standards Track [Page 7]
RFC 4803 GMPLS LSR MIB February 2007
In gmplsLabelTable:
{
gmplsLabelInterface = 13,
gmplsLabelIndex = 1,
gmplsLabelSubindex = 0,
gmplsLabelType = gmplsFreeformLabel(3),
gmplsLabelFreeform = 0xFEDCBA9876543210
gmplsLabelRowStatus = createAndGo(4)
}
We must next create the appropriate in-segment and out-segment
entries. These are done in [RFC3813] using the mplsInSegmentTable
and mplsOutSegmentTable. Note that we use a row pointer to the two
rows in the gmplsLabelTable rather than specify the labels explicitly
in the in- and out-segment tables. Also note that the row status for
each row is set to createAndWait(5) to allow corresponding entries in
the gmplsInSegmentTable and gmplsOutSegmentTable to be created.
For the forward direction.
In mplsInSegmentTable:
{
mplsInSegmentIndex = 0x00000015
mplsInSegmentLabel = 0, -- incoming label in label table
mplsInSegmentNPop = 1,
mplsInSegmentInterface = 12, -- incoming interface
-- RowPointer MUST point to the first accessible column.
mplsInSegmentTrafficParamPtr = 0.0,
mplsInSegmentLabelPtr = gmplsLabelTable(12,1,0)
mplsInSegmentRowStatus = createAndWait(5)
}
In mplsOutSegmentTable:
{
mplsOutSegmentIndex = 0x00000012,
mplsOutSegmentInterface = 13, -- outgoing interface
mplsOutSegmentPushTopLabel = true(1),
mplsOutSegmentTopLabel = 0, -- outgoing label in label table
-- RowPointer MUST point to the first accessible column.
mplsOutSegmentTrafficParamPtr = 0.0,
mplsOutSegmentLabelPtr = gmplsLabelTable(13,1,0)
mplsOutSegmentRowStatus = createAndWait(5)
}
Nadeau & Farrel Standards Track [Page 8]
RFC 4803 GMPLS LSR MIB February 2007
For the reverse direction.
In mplsInSegmentTable:
{
mplsInSegmentIndex = 0x00000016
mplsInSegmentLabel = 0, -- incoming label in label table
mplsInSegmentNPop = 1,
mplsInSegmentInterface = 13, -- incoming interface
-- RowPointer MUST point to the first accessible column.
mplsInSegmentTrafficParamPtr = 0.0,
mplsInSegmentLabelPtr = gmplsLabelTable(13,1,0)
mplsInSegmentRowStatus = createAndWait(5)
}
In mplsOutSegmentTable:
{
mplsOutSegmentIndex = 0x00000013,
mplsOutSegmentInterface = 12, -- outgoing interface
mplsOutSegmentPushTopLabel = true(1),
mplsOutSegmentTopLabel = 0, -- outgoing label in label table
-- RowPointer MUST point to the first accessible column.
mplsOutSegmentTrafficParamPtr = 0.0,
mplsOutSegmentLabelPtr = gmplsLabelTable(12,1,0)
mplsOutSegmentRowStatus = createAndWait(5)
}
These table entries are extended by entries in the
gmplsInSegmentTable and gmplsOutSegmentTable. Note that the nature
of the 'extends' relationship is a sparse augmentation so that the
entry in the gmplsInSegmentTable has the same index values as the
entry in the mplsInSegmentTable. Similarly, the entry in the
gmplsOutSegmentTable has the same index values as the entry in the
mplsOutSegmentTable.
First for the forward direction:
In gmplsInSegmentTable(0x00000015)
{
gmplsInSegmentDirection = forward(1)
}
In gmplsOutSegmentTable(0x00000012)
{
gmplsOutSegmentDirection = forward(1)
}
Nadeau & Farrel Standards Track [Page 9]
RFC 4803 GMPLS LSR MIB February 2007
Next for the reverse direction:
In gmplsInSegmentTable(0x00000016)
{
gmplsInSegmentDirection = reverse(2)
}
In gmplsOutSegmentTable(0x00000013)
{
gmplsOutSegmentDirection = reverse(2)
}
Next, two cross-connect entries are created in the mplsXCTable of the
MPLS-LSR-STD-MIB [RFC3813], thereby associating the newly created
segments together.
In mplsXCTable:
{
mplsXCIndex = 0x01,
mplsXCInSegmentIndex = 0x00000015,
mplsXCOutSegmentIndex = 0x00000012,
mplsXCLspId = 0x0102 -- unique ID
mplsXCLabelStackIndex = 0x00, -- only a single outgoing label
mplsXCRowStatus = createAndGo(4)
}
In mplsXCTable:
{
mplsXCIndex = 0x02,
mplsXCInSegmentIndex = 0x00000016,
mplsXCOutSegmentIndex = 0x00000013,
mplsXCLspId = 0x0102 -- unique ID
mplsXCLabelStackIndex = 0x00, -- only a single outgoing label
mplsXCRowStatus = createAndGo(4)
}
Finally, the in-segments and out-segments are activated.
In mplsInSegmentTable(0x00000015):
{
mplsInSegmentRowStatus = active(1)
}
In mplsInSegmentTable(0x00000016):
{
mplsInSegmentRowStatus = active(1)
}
Nadeau & Farrel Standards Track [Page 10]
RFC 4803 GMPLS LSR MIB February 2007
In mplsOutSegmentTable(0x00000012):
{
mplsOutSegmentRowStatus = active(1)
}
In mplsOutSegmentTable(0x00000013):
{
mplsOutSegmentRowStatus = active(1)
}
7. GMPLS Label Switching Router MIB Definitions
This MIB module makes reference to the following documents:
[RFC2578], [RFC2579], [RFC2580], [RFC2863], [RFC3209], [RFC3443],
[RFC3468], [RFC3472], [RFC3473], [RFC3811], [RFC3813], and [RFC4801].
GMPLS-LSR-STD-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE, Unsigned32, zeroDotZero
FROM SNMPv2-SMI -- RFC 2578
MODULE-COMPLIANCE, OBJECT-GROUP
FROM SNMPv2-CONF -- RFC 2580
RowPointer
FROM SNMPv2-TC -- RFC 2579
GmplsSegmentDirectionTC
FROM GMPLS-TC-STD-MIB -- RFC 4801
mplsInterfaceIndex, mplsInSegmentIndex, mplsOutSegmentIndex,
mplsInterfaceGroup, mplsInSegmentGroup, mplsOutSegmentGroup,
mplsXCGroup, mplsPerfGroup, mplsLsrNotificationGroup
FROM MPLS-LSR-STD-MIB -- RFC 3813
ifGeneralInformationGroup, ifCounterDiscontinuityGroup
FROM IF-MIB -- RFC 2863
mplsStdMIB
FROM MPLS-TC-STD-MIB -- RFC 3811
;
gmplsLsrStdMIB MODULE-IDENTITY
LAST-UPDATED
"200702270000Z" -- 27 February 2007 00:00:00 GMT
ORGANIZATION
"IETF Common Control And Measurement Plane (CCAMP) Working Group"
CONTACT-INFO
" Thomas D. Nadeau
Cisco Systems, Inc.
Email: tnadeau@cisco.com
Adrian Farrel
Old Dog Consulting
Nadeau & Farrel Standards Track [Page 11]
RFC 4803 GMPLS LSR MIB February 2007
Email: adrian@olddog.co.uk
Comments about this document should be emailed directly to the
CCAMP working group mailing list at ccamp@ops.ietf.org."
DESCRIPTION
"Copyright (C) The IETF Trust (2007). This version of
this MIB module is part of RFC 4803; see the RFC itself for
full legal notices.
This MIB module contains managed object definitions for the
Generalized Multiprotocol (GMPLS) Label Switching Router as
defined in Generalized Multi-Protocol Label Switching (GMPLS)
Architecture, Mannie et al., RFC 3945, October 2004."
REVISION
"200702270000Z" -- 27 February 2007 00:00:00 GMT
DESCRIPTION
"Initial version issued as part of RFC 4803."
::= { mplsStdMIB 15 }
-- no notifications are currently defined.
gmplsLsrObjects OBJECT IDENTIFIER ::= { gmplsLsrStdMIB 1 }
gmplsLsrConformance OBJECT IDENTIFIER ::= { gmplsLsrStdMIB 2 }
gmplsInterfaceTable OBJECT-TYPE
SYNTAX SEQUENCE OF GmplsInterfaceEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table specifies per-interface GMPLS capability and
associated information. It extends the information in the
mplsInterfaceTable of MPLS-LSR-STD-MIB through a
sparse augmentation relationship."
REFERENCE
"1. Multiprotocol Label Switching (MPLS) Label Switching
Router (LSR) Management Information Base (MIB), RFC 3813."
::= { gmplsLsrObjects 1 }
gmplsInterfaceEntry OBJECT-TYPE
SYNTAX GmplsInterfaceEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row in this table is created automatically by an
LSR for each interface that is both capable of supporting
GMPLS and configured to support GMPLS. Note that
support of GMPLS is not limited to control plane signaling,
but may include data-plane-only function configured through
SNMP SET commands performed on this MIB module.
Nadeau & Farrel Standards Track [Page 12]
RFC 4803 GMPLS LSR MIB February 2007
A conceptual row in this table may also be created via SNMP
SET commands or automatically by the LSR to supplement a
conceptual row in the mplsInterfaceTable where the interface
is not capable of GMPLS but where the other objects carried
in this row provide useful additional information for an
MPLS interface.
A conceptual row in this table will exist if and only if a
corresponding entry in the mplsInterfaceTable exists, and a
corresponding entry in the ifTable exists with ifType = mpls(166).
If the associated entry in the ifTable is operationally disabled
(thus removing the GMPLS capabilities on the interface) or the
entry in the mplsInterfaceTable is deleted, the corresponding entry
in this table MUST be deleted shortly thereafter.
The indexes are the same as for the mplsInterfaceTable. Thus, the
entry with index 0 represents the per-platform label space and
contains parameters that apply to all interfaces that
participate in the per-platform label space."
REFERENCE
"1. Multiprotocol Label Switching (MPLS) Label Switching
Router (LSR) Management Information Base (MIB), RFC 3813."
INDEX { mplsInterfaceIndex }
::= { gmplsInterfaceTable 1 }
GmplsInterfaceEntry ::= SEQUENCE {
gmplsInterfaceSignalingCaps BITS,
gmplsInterfaceRsvpHelloPeriod Unsigned32
}
gmplsInterfaceSignalingCaps OBJECT-TYPE
SYNTAX BITS {
unknown(0),
rsvpGmpls(1),
crldpGmpls(2), -- note the use of CR-LDP is deprecated
otherGmpls(3)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Defines the signaling capabilities on this interface. Multiple
bits may legitimately be set at once, but if 'unknown' is set
then no other bit may be set. Setting no bits implies that GMPLS
signaling cannot be performed on this interface and all LSPs
must be manually provisioned or that this table entry is only
present to supplement an entry in the mplsInterfaceTable by
providing the information carried in other objects in this row."
REFERENCE
Nadeau & Farrel Standards Track [Page 13]
RFC 4803 GMPLS LSR MIB February 2007
"1. Generalized MPLS Signaling - CR-LDP Extensions, RFC 3472.
2. The Multiprotocol Label Switching (MPLS) Working Group
decision on MPLS signaling protocols, RFC 3468.
3. Generalized MPLS Signaling - RSVP-TE Extensions, RFC 3473."
DEFVAL { { rsvpGmpls } }
::= { gmplsInterfaceEntry 1 }
gmplsInterfaceRsvpHelloPeriod OBJECT-TYPE
SYNTAX Unsigned32
UNITS "milliseconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Period, in milliseconds, between sending Resource Reservation
Protocol (RSVP) Hello messages on this interface. A value of 0
indicates that no Hello messages should be sent on this
interface.
This object is only valid if gmplsInterfaceSignalingCaps has no
bits set or includes the rsvpGmpls bit."
REFERENCE
"1. RSVP-TE: Extensions to RSVP for LSP Tunnels, RFC 3209,
section 5.
2. Generalized MPLS Signaling - RSVP-TE Extensions, RFC 3473,
section 9.3."
DEFVAL { 3000 }
::= { gmplsInterfaceEntry 2 }
gmplsInSegmentTable OBJECT-TYPE
SYNTAX SEQUENCE OF GmplsInSegmentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table sparse augments the mplsInSegmentTable of
MPLS-LSR-STD-MIB to provide GMPLS-specific information about
incoming segments to an LSR."
REFERENCE
"1. Multiprotocol Label Switching (MPLS) Label Switching
Router (LSR) Management Information Base (MIB), RFC 3813."
::= { gmplsLsrObjects 2 }
gmplsInSegmentEntry OBJECT-TYPE
SYNTAX GmplsInSegmentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table extends the representation of an incoming
segment represented by an entry in the mplsInSegmentTable in
Nadeau & Farrel Standards Track [Page 14]
RFC 4803 GMPLS LSR MIB February 2007
MPLS-LSR-STD-MIB through a sparse augmentation. An entry can be
created by a network administrator via SNMP SET commands, or in
response to signaling protocol events.
Note that the storage type for this entry is given by the value
of mplsInSegmentStorageType in the corresponding entry of the
mplsInSegmentTable."
REFERENCE
"1. Multiprotocol Label Switching (MPLS) Label Switching
Router (LSR) Management Information Base (MIB), RFC 3813."
INDEX { mplsInSegmentIndex }
::= { gmplsInSegmentTable 1 }
GmplsInSegmentEntry ::= SEQUENCE {
gmplsInSegmentDirection GmplsSegmentDirectionTC,
gmplsInSegmentExtraParamsPtr RowPointer
}
gmplsInSegmentDirection OBJECT-TYPE
SYNTAX GmplsSegmentDirectionTC
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object indicates the direction of data flow on this
segment. This object cannot be modified if
mplsInSegmentRowStatus for the corresponding entry in the
mplsInSegmentTable is active(1)."
REFERENCE
"1. Multiprotocol Label Switching (MPLS) Label Switching
Router (LSR) Management Information Base (MIB), RFC 3813."
DEFVAL { forward }
::= { gmplsInSegmentEntry 1 }
gmplsInSegmentExtraParamsPtr OBJECT-TYPE
SYNTAX RowPointer
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Some tunnels will run over transports that can usefully support
technology-specific additional parameters (for example,
Synchronous Optical Network (SONET) resource usage). Such can be
supplied from an external table and referenced from here. A value
of zeroDotZero in this attribute indicates that there is no such
additional information."
DEFVAL { zeroDotZero }
::= { gmplsInSegmentEntry 2 }
gmplsOutSegmentTable OBJECT-TYPE
Nadeau & Farrel Standards Track [Page 15]
RFC 4803 GMPLS LSR MIB February 2007
SYNTAX SEQUENCE OF GmplsOutSegmentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table sparse augments the mplsOutSegmentTable of
MPLS-LSR-STD-MIB to provide GMPLS-specific information about
outgoing segments from an LSR."
REFERENCE
"1. Multiprotocol Label Switching (MPLS) Label Switching
Router (LSR) Management Information Base (MIB), RFC 3813."
::= { gmplsLsrObjects 3 }
gmplsOutSegmentEntry OBJECT-TYPE
SYNTAX GmplsOutSegmentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table extends the representation of an outgoing
segment represented by an entry in the mplsOutSegmentTable of
MPLS-LSR-STD-MIB through a sparse augmentation. An entry can be
created by a network administrator via SNMP SET commands, or in
response to signaling protocol events.
Note that the storage type for this entry is given by the value
of mplsOutSegmentStorageType in the corresponding entry of the
mplsOutSegmentTable."
REFERENCE
"1. Multiprotocol Label Switching (MPLS) Label Switching
Router (LSR) Management Information Base (MIB), RFC 3813."
INDEX { mplsOutSegmentIndex }
::= { gmplsOutSegmentTable 1 }
GmplsOutSegmentEntry ::= SEQUENCE {
gmplsOutSegmentDirection GmplsSegmentDirectionTC,
gmplsOutSegmentTTLDecrement Unsigned32,
gmplsOutSegmentExtraParamsPtr RowPointer
}
gmplsOutSegmentDirection OBJECT-TYPE
SYNTAX GmplsSegmentDirectionTC
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object indicates the direction of data flow on this
segment. This object cannot be modified if
mplsOutSegmentRowStatus for the corresponding entry in the
mplsOutSegmentTable is active(1)."
REFERENCE
Nadeau & Farrel Standards Track [Page 16]
RFC 4803 GMPLS LSR MIB February 2007
"1. Multiprotocol Label Switching (MPLS) Label Switching
Router (LSR) Management Information Base (MIB), RFC 3813."
DEFVAL { forward }
::= { gmplsOutSegmentEntry 1 }
gmplsOutSegmentTTLDecrement OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object indicates the amount by which to decrement the Time
to Live (TTL) of any payload packets forwarded on this segment if
per-hop decrementing is being done.
A value of zero indicates that no decrement should be made or
that per-hop decrementing is not in use.
See the gmplsTunnelTTLDecrement object in the gmplsTunnelTable
of GMPLS-TE-STD-MIB for a value by which to decrement the TTL
for the whole of a tunnel.
This object cannot be modified if mplsOutSegmentRowStatus for
the associated entry in the mplsOutSegmentTable is active(1)."
REFERENCE
"1. Time To Live (TTL) Processing in Multi-Protocol Label
Switching (MPLS) Networks, RFC 3443.
2. Generalized Multiprotocol Label Switching (GMPLS) Traffic
Engineering Management Information Base, RFC 4802."
DEFVAL { 0 }
::= { gmplsOutSegmentEntry 2 }
gmplsOutSegmentExtraParamsPtr OBJECT-TYPE
SYNTAX RowPointer
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Some tunnels will run over transports that can usefully support
technology-specific additional parameters (for example, SONET
resource usage). Such can be supplied from an external table and
referenced from here.
A value of zeroDotZero in this attribute indicates that there is
no such additional information."
DEFVAL { zeroDotZero }
::= { gmplsOutSegmentEntry 3 }
gmplsLsrGroups
OBJECT IDENTIFIER ::= { gmplsLsrConformance 1 }
Nadeau & Farrel Standards Track [Page 17]
RFC 4803 GMPLS LSR MIB February 2007
gmplsLsrCompliances
OBJECT IDENTIFIER ::= { gmplsLsrConformance 2 }
-- Compliance requirement for fully compliant implementations.
gmplsLsrModuleFullCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"Compliance statement for agents that provide full support for
GMPLS-LSR-STD-MIB.
The mandatory group has to be implemented by all LSRs that
originate, terminate, or act as transit for TE-LSPs/tunnels.
In addition, depending on the type of tunnels supported, other
groups become mandatory as explained below."
MODULE IF-MIB -- The Interfaces Group MIB, RFC 2863.
MANDATORY-GROUPS {
ifGeneralInformationGroup,
ifCounterDiscontinuityGroup
}
MODULE MPLS-LSR-STD-MIB -- The MPLS-LSR-STD-MIB, RFC3813
MANDATORY-GROUPS {
mplsInterfaceGroup,
mplsInSegmentGroup,
mplsOutSegmentGroup,
mplsXCGroup,
mplsPerfGroup,
mplsLsrNotificationGroup
}
MODULE -- this module
MANDATORY-GROUPS {
gmplsInterfaceGroup,
gmplsInSegmentGroup,
gmplsOutSegmentGroup
}
OBJECT gmplsInSegmentDirection
SYNTAX GmplsSegmentDirectionTC
MIN-ACCESS read-only
DESCRIPTION
"The only valid value for unidirectional LSPs is forward(1)."
Nadeau & Farrel Standards Track [Page 18]
RFC 4803 GMPLS LSR MIB February 2007
OBJECT gmplsOutSegmentDirection
SYNTAX GmplsSegmentDirectionTC
MIN-ACCESS read-only
DESCRIPTION
"The only valid value for unidirectional LSPs is forward(1)."
OBJECT gmplsOutSegmentTTLDecrement
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT gmplsInSegmentExtraParamsPtr
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT gmplsOutSegmentExtraParamsPtr
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
::= { gmplsLsrCompliances 1 }
-- Compliance requirement for implementations that provide read-only
-- access.
gmplsLsrModuleReadOnlyCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"Compliance requirement for implementations that only provide
read-only support for GMPLS-LSR-STD-MIB. Such devices can then
be monitored but cannot be configured using this MIB module."
MODULE IF-MIB -- The interfaces Group MIB, RFC 2863
MANDATORY-GROUPS {
ifGeneralInformationGroup,
ifCounterDiscontinuityGroup
}
MODULE MPLS-LSR-STD-MIB
MANDATORY-GROUPS {
mplsInterfaceGroup,
mplsInSegmentGroup,
mplsOutSegmentGroup,
mplsXCGroup,
mplsPerfGroup
}
Nadeau & Farrel Standards Track [Page 19]
RFC 4803 GMPLS LSR MIB February 2007
MODULE -- this module
MANDATORY-GROUPS {
gmplsInterfaceGroup,
gmplsInSegmentGroup,
gmplsOutSegmentGroup
}
OBJECT gmplsInterfaceSignalingCaps
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT gmplsInterfaceRsvpHelloPeriod
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT gmplsInSegmentDirection
SYNTAX GmplsSegmentDirectionTC
MIN-ACCESS read-only
DESCRIPTION
"The only valid value for unidirectional LSPs is forward(1)."
OBJECT gmplsInSegmentExtraParamsPtr
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT gmplsOutSegmentDirection
MIN-ACCESS read-only
DESCRIPTION
"The only valid value for unidirectional LSPs is forward(1)."
OBJECT gmplsOutSegmentTTLDecrement
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT gmplsOutSegmentExtraParamsPtr
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
::= { gmplsLsrCompliances 2 }
gmplsInterfaceGroup OBJECT-GROUP
OBJECTS {
gmplsInterfaceSignalingCaps,
Nadeau & Farrel Standards Track [Page 20]
RFC 4803 GMPLS LSR MIB February 2007
gmplsInterfaceRsvpHelloPeriod
}
STATUS current
DESCRIPTION
"Collection of objects that provide additional
information for an MPLS interface and are needed
for GMPLS interface configuration and performance
information."
::= { gmplsLsrGroups 1 }
gmplsInSegmentGroup OBJECT-GROUP
OBJECTS {
gmplsInSegmentDirection,
gmplsInSegmentExtraParamsPtr
}
STATUS current
DESCRIPTION
"Collection of objects that provide additional
information for an MPLS in-segment and are needed
for GMPLS in-segment configuration and performance
information."
::= { gmplsLsrGroups 2 }
gmplsOutSegmentGroup OBJECT-GROUP
OBJECTS {
gmplsOutSegmentDirection,
gmplsOutSegmentTTLDecrement,
gmplsOutSegmentExtraParamsPtr
}
STATUS current
DESCRIPTION
"Collection of objects that provide additional
information for an MPLS out-segment and are needed
for GMPLS out-segment configuration and performance
information."
::= { gmplsLsrGroups 3 }
END
Nadeau & Farrel Standards Track [Page 21]
RFC 4803 GMPLS LSR MIB February 2007
8. GMPLS Label MIB Definitions
This MIB module makes reference to the following documents:
[RFC2578], [RFC2579], [RFC2580], [RFC2863], [RFC3032], [RFC3289],
[RFC3471], [RFC3811], and [RFC4801].
GMPLS-LABEL-STD-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE, Unsigned32, Integer32
FROM SNMPv2-SMI -- RFC 2578
MODULE-COMPLIANCE, OBJECT-GROUP
FROM SNMPv2-CONF -- RFC 2580
RowStatus, StorageType
FROM SNMPv2-TC -- RFC 2579
InterfaceIndexOrZero
FROM IF-MIB -- RFC 2863
IndexIntegerNextFree
FROM DIFFSERV-MIB -- RFC 3289
MplsLabel, mplsStdMIB
FROM MPLS-TC-STD-MIB -- RFC 3811
GmplsLabelTypeTC, GmplsFreeformLabelTC
FROM GMPLS-TC-STD-MIB -- RFC 4801
;
gmplsLabelStdMIB MODULE-IDENTITY
LAST-UPDATED
"200702270000Z" -- 27 February 2007 00:00:00 GMT
ORGANIZATION
"IETF Common Control and Measurement Plane (CCAMP) Working Group"
CONTACT-INFO
" Thomas D. Nadeau
Cisco Systems, Inc.
Email: tnadeau@cisco.com
Adrian Farrel
Old Dog Consulting
Email: adrian@olddog.co.uk
Comments about this document should be emailed directly to the
CCAMP working group mailing list at ccamp@ops.ietf.org."
DESCRIPTION
"Copyright (C) The IETF Trust (2007). This version of
this MIB module is part of RFC 4803; see the RFC itself for
full legal notices.
Nadeau & Farrel Standards Track [Page 22]
RFC 4803 GMPLS LSR MIB February 2007
This MIB module contains managed object definitions for labels
within GMPLS systems as defined in
Generalized Multi-Protocol Label Switching (GMPLS) Signaling
Functional Description, Berger, L. (Editor), RFC 3471,
January 2003."
REVISION
"200702270000Z" -- 27 February 2007 00:00:00 GMT
DESCRIPTION
"Initial version issued as part of RFC 4803."
::= { mplsStdMIB 16 }
-- no notifications are currently defined.
gmplsLabelObjects OBJECT IDENTIFIER ::= { gmplsLabelStdMIB 1 }
gmplsLabelConformance OBJECT IDENTIFIER ::= { gmplsLabelStdMIB 2 }
gmplsLabelIndexNext OBJECT-TYPE
SYNTAX IndexIntegerNextFree
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains an unused value for gmplsLabelIndex,
or a zero to indicate that no unused value exists or is
available.
A management application wishing to create a row in the
gmplsLabelTable may read this object and then attempt to
create a row in the table. If row creation fails (because
another application has already created a row with the
supplied index), the management application should read this
object again to get a new index value.
When a row is created in the gmplsLabelTable with the
gmplsLabelIndex value held by this object, an implementation
MUST change the value in this object."
::= { gmplsLabelObjects 1 }
gmplsLabelTable OBJECT-TYPE
SYNTAX SEQUENCE OF GmplsLabelEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table of GMPLS Labels. This table allows the representation
of the more complex label forms required for GMPLS that cannot
be held within the TEXTUAL-CONVENTION MplsLabel; that is, labels
that cannot be encoded within 32 bits. It is, nevertheless, also
capable of holding 32-bit labels or regular MPLS Labels if
desired.
Nadeau & Farrel Standards Track [Page 23]
RFC 4803 GMPLS LSR MIB February 2007
Each entry in this table represents an individual GMPLS Label
value. The representation of Labels in tables in other MIB
modules may be achieved by a referrence to an entry in this
table by means of a row pointer into this table. The indexing
of this table provides for arbitrary indexing and also for
concatenation of labels.
For an example of label concatenation, see RFC 3945, section 7.1.
In essence, a GMPLS Label may be composite in order to identify
a set of resources in the data plane. Practical examples are
timeslots and wavelength sets (which are not contiguous like
wavebands).
The indexing mechanism allows multiple entries in this table to
be seen as a sequence of labels that should be concatenated.
Ordering is potentially very sensitive for concatenation."
REFERENCE
"1. Generalized Multiprotocol Label Switching (GMPLS)
Architecture, RFC 3945, section 7.1."
::= { gmplsLabelObjects 2 }
gmplsLabelEntry OBJECT-TYPE
SYNTAX GmplsLabelEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table represents a single label value. There
are three indexes into the table.
- The interface index may be helpful to distinguish which
labels are in use on which interfaces or to handle cases
where there are a very large number of labels in use in the
system. When label representation is desired to apply to the
whole system or when it is not important to distinguish
labels by their interfaces, this index MAY be set to zero.
- The label index provides a way of identifying the label.
- The label sub-index is only used for concatenated labels. It
identifies each component label. When non-concatenated labels
are used, this index SHOULD be set to zero.
A storage type object is supplied to control the storage type
for each entry, but implementations should note that the storage
type of conceptual rows in other tables that include row
pointers to an entry in this table SHOULD dictate the storage
type of the rows in this table where the row in the other table
is more persistent."
Nadeau & Farrel Standards Track [Page 24]
RFC 4803 GMPLS LSR MIB February 2007
INDEX {
gmplsLabelInterface,
gmplsLabelIndex,
gmplsLabelSubindex }
::= { gmplsLabelTable 1 }
GmplsLabelEntry ::= SEQUENCE {
gmplsLabelInterface InterfaceIndexOrZero,
gmplsLabelIndex Unsigned32,
gmplsLabelSubindex Unsigned32,
gmplsLabelType GmplsLabelTypeTC,
gmplsLabelMplsLabel MplsLabel,
gmplsLabelPortWavelength Unsigned32,
gmplsLabelFreeform GmplsFreeformLabelTC,
gmplsLabelSonetSdhSignalIndex Integer32,
gmplsLabelSdhVc Integer32,
gmplsLabelSdhVcBranch Integer32,
gmplsLabelSonetSdhBranch Integer32,
gmplsLabelSonetSdhGroupBranch Integer32,
gmplsLabelWavebandId Unsigned32,
gmplsLabelWavebandStart Unsigned32,
gmplsLabelWavebandEnd Unsigned32,
gmplsLabelStorageType StorageType,
gmplsLabelRowStatus RowStatus
}
gmplsLabelInterface OBJECT-TYPE
SYNTAX InterfaceIndexOrZero
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The interface on which this label is used. If this object is set
to zero, the label MUST have applicability across the
whole system and not be limited to a single interface."
::= { gmplsLabelEntry 1 }
gmplsLabelIndex OBJECT-TYPE
SYNTAX Unsigned32 (0..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An arbitrary index into the table to identify a label.
Note that implementations that are representing 32-bit labels
within this table MAY choose to align this index with the value
of the label, and this may result in the use of the value zero
since it represents a valid label value. Such implementation
should be aware of the implications of sparsely populated
Nadeau & Farrel Standards Track [Page 25]
RFC 4803 GMPLS LSR MIB February 2007
tables.
A management application may read the gmplsLabelIndexNext
object to find a suitable value for this object."
::= { gmplsLabelEntry 2 }
gmplsLabelSubindex OBJECT-TYPE
SYNTAX Unsigned32 (0..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"In conjunction with gmplsLabelInterface and gmplsLabelIndex,
this object uniquely identifies this row. This sub-index allows
a single GMPLS Label to be defined as a concatenation of labels.
This is particularly useful in TDM.
The ordering of sub-labels is strict with the sub-label with
the lowest gmplsLabelSubindex appearing first. Note that all
sub-labels of a single GMPLS Label must share the same
gmplsLabelInterface and gmplsLabelIndex values. For labels that
are not composed of concatenated sub-labels, this value SHOULD
be set to zero."
::= { gmplsLabelEntry 3 }
gmplsLabelType OBJECT-TYPE
SYNTAX GmplsLabelTypeTC
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Identifies the type of this label. Note that this object does
not determine whether MPLS or GMPLS signaling is in use: a value
of gmplsMplsLabel(1) denotes that an MPLS Packet Label is
present in the gmplsLabelMplsLabel object and encoded using the
MplsLabel TEXTUAL-CONVENTION (may be a 20-bit MPLS Label, a 10-
or 23-bit Frame Relay Label, or an Asynchronous Transfer Mode
(ATM) Label), but does not describe whether this is signaled
using MPLS or GMPLS.
The value of this object helps determine which of the following
objects are valid. This object cannot be modified if
gmplsLabelRowStatus is active(1)."
REFERENCE
"1. Generalized Multi-Protocol Label Switching (GMPLS) Signaling
Functional Description, RFC 3471, section 3."
::= { gmplsLabelEntry 4 }
gmplsLabelMplsLabel OBJECT-TYPE
SYNTAX MplsLabel
Nadeau & Farrel Standards Track [Page 26]
RFC 4803 GMPLS LSR MIB February 2007
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of an MPLS Label (that is a Packet Label) if this
table is used to store it. This may be used in MPLS systems even
though the label values can be adequately stored in the MPLS MIB
modules (MPLS-LSR-STD-MIB and MPLS-TE-STD-MIB). Furthermore, in
mixed MPLS and GMPLS systems, it may be advantageous to store all
labels in a single label table. Lastly, in GMPLS systems where
Packet Labels are used (that is in systems that use GMPLS
signaling and GMPLS Labels for packet switching), it may be
desirable to use this table.
This object is only valid if gmplsLabelType is set
to gmplsMplsLabel(1). This object cannot be modified if
gmplsLabelRowStatus is active(1)."
REFERENCE
"1. MPLS Label Stack Encoding, RFC 3032."
DEFVAL { 0 }
::= { gmplsLabelEntry 5 }
gmplsLabelPortWavelength OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of a Port or Wavelength Label when carried as a
Generalized Label. Only valid if gmplsLabelType is set to
gmplsPortWavelengthLabel(2). This object cannot be modified if
gmplsLabelRowStatus is active(1)."
REFERENCE
"1. Generalized Multi-Protocol Label Switching (GMPLS) Signaling
Functional Description, RFC 3471, section 3.2.1.1."
DEFVAL { 0 }
::= { gmplsLabelEntry 6 }
gmplsLabelFreeform OBJECT-TYPE
SYNTAX GmplsFreeformLabelTC
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of a Freeform Generalized Label that does not conform
to one of the standardized label encodings or that an
implementation chooses to represent as an octet string without
further decoding. Only valid if gmplsLabelType is set to
gmplsFreeformLabel(3). This object cannot be modified
if gmplsLabelRowStatus is active(1)."
REFERENCE
Nadeau & Farrel Standards Track [Page 27]
RFC 4803 GMPLS LSR MIB February 2007
"1. Generalized Multi-Protocol Label Switching (GMPLS) Signaling
Functional Description, RFC 3471, section 3.2."
DEFVAL { '00'h }
::= { gmplsLabelEntry 7 }
gmplsLabelSonetSdhSignalIndex OBJECT-TYPE
SYNTAX Integer32 (0..4095)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The Signal Index value (S) of a SONET or SDH Generalized Label.
Zero indicates that this field is non-significant. Only valid if
gmplsLabelType is set to gmplsSonetLabel(4) or gmplsSdhLabel(5).
This object cannot be modified if gmplsLabelRowStatus is
active(1)."
REFERENCE
"1. Generalized Multi-Protocol Label Switching (GMPLS) Extensions
for Synchronous Optical Network (SONET) and Synchronous
Digital Hierarchy (SDH) Control, RFC 4606, section 3."
DEFVAL { 0 }
::= { gmplsLabelEntry 8 }
gmplsLabelSdhVc OBJECT-TYPE
SYNTAX Integer32 (0..15)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The VC Indicator (U) of an SDH Generalized Label. Zero indicates
that this field is non-significant. Only valid if gmplsLabelType
is set to gmplsSdhLabel(5). This object cannot be modified if
gmplsLabelRowStatus is active(1)."
REFERENCE
"1. Generalized Multi-Protocol Label Switching (GMPLS) Extensions
for Synchronous Optical Network (SONET) and Synchronous
Digital Hierarchy (SDH) Control, RFC 4606, section 3."
DEFVAL { 0 }
::= { gmplsLabelEntry 9 }
gmplsLabelSdhVcBranch OBJECT-TYPE
SYNTAX Integer32 (0..15)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The VC Branch Indicator (K) of an SDH Generalized Label. Zero
indicates that this field is non-significant. Only valid if
gmplsLabelType is set to gmplsSdhLabel(5). This
object cannot be modified if gmplsLabelRowStatus is active(1)."
REFERENCE
Nadeau & Farrel Standards Track [Page 28]
RFC 4803 GMPLS LSR MIB February 2007
"1. Generalized Multi-Protocol Label Switching (GMPLS) Extensions
for Synchronous Optical Network (SONET) and Synchronous
Digital Hierarchy (SDH) Control, RFC 4606, section 3."
DEFVAL { 0 }
::= { gmplsLabelEntry 10 }
gmplsLabelSonetSdhBranch OBJECT-TYPE
SYNTAX Integer32 (0..15)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The Branch Indicator (L) of a SONET or SDH Generalized Label.
Zero indicates that this field is non-significant. Only valid
gmplsLabelType is set to gmplsSonetLabel(4) or
gmplsSdhLabel(5). This object cannot be modified if
gmplsLabelRowStatus is active(1)."
REFERENCE
"1. Generalized Multi-Protocol Label Switching (GMPLS) Extensions
for Synchronous Optical Network (SONET) and Synchronous
Digital Hierarchy (SDH) Control, RFC 4606, section 3."
DEFVAL { 0 }
::= { gmplsLabelEntry 11 }
gmplsLabelSonetSdhGroupBranch OBJECT-TYPE
SYNTAX Integer32 (0..15)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The Group Branch Indicator (M) of a SONET or SDH Generalized
Label. Zero indicates that this field is non-significant.
Only valid if gmplsLabelType is set to gmplsSonetLabel(4) or
gmplsSdhLabel(5). This object cannot be modified if
gmplsLabelRowStatus is active(1)."
REFERENCE
"1. Generalized Multi-Protocol Label Switching (GMPLS) Extensions
for Synchronous Optical Network (SONET) and Synchronous
Digital Hierarchy (SDH) Control, RFC 4606, section 3."
DEFVAL { 0 }
::= { gmplsLabelEntry 12 }
gmplsLabelWavebandId OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The waveband identifier component of a Waveband Label. Only
valid if gmplsLabelType is set to gmplsWavebandLabel(6). This
object cannot be modified if gmplsLabelRowStatus is active(1)."
Nadeau & Farrel Standards Track [Page 29]
RFC 4803 GMPLS LSR MIB February 2007
REFERENCE
"1. Generalized Multi-Protocol Label Switching (GMPLS) Signaling
Functional Description, RFC 3471, section 3.3."
DEFVAL { 0 }
::= { gmplsLabelEntry 13 }
gmplsLabelWavebandStart OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The starting label component of a Waveband Label. Only valid if
gmplsLabelType is set to gmplsWavebandLabel(6). This object
cannot be modified if gmplsLabelRowStatus is active(1)."
REFERENCE
"1. Generalized Multi-Protocol Label Switching (GMPLS) Signaling
Functional Description, RFC 3471, section 3.3."
DEFVAL { 0 }
::= { gmplsLabelEntry 14 }
gmplsLabelWavebandEnd OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The end label component of a Waveband Label. Only valid if
gmplsLabelType is set to gmplsWavebandLabel(6). This object
cannot be modified if gmplsLabelRowStatus is active(1)."
REFERENCE
"1. Generalized Multi-Protocol Label Switching (GMPLS) Signaling
Functional Description, RFC 3471, section 3.3."
DEFVAL { 0 }
::= { gmplsLabelEntry 15 }
gmplsLabelStorageType OBJECT-TYPE
SYNTAX StorageType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This variable indicates the storage type for this row. The
agent MUST ensure that this object's value remains consistent
with the storage type of any rows in other tables that contain
pointers to this row. In particular, the storage type of this
row must be at least as permanent as that of any row that points
to it.
Conceptual rows having the value 'permanent' need not
allow write-access to any columnar objects in the row."
REFERENCE
Nadeau & Farrel Standards Track [Page 30]
RFC 4803 GMPLS LSR MIB February 2007
"1. Textual Conventions for SMIv2, STD 58, RFC 2579, section 2."
DEFVAL { volatile }
::= { gmplsLabelEntry 16 }
gmplsLabelRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This variable is used to create, modify, and/or delete a row in
this table. When a row in this table has a row in the active(1)
state, no objects in this row can be modified except the
gmplsLabelRowStatus and gmplsLabelStorageType.
The gmplsLabelType object does not have a default and must be
set before a row can become active. The corresponding label
objects (dependent on the value of gmplsLabelType) should also
be set unless they happen to need to use the specified default
values as follows:
gmplsLabelType setting objects to be set
--------------------------------------------------------------
gmplsMplsLabel(1) gmplsLabelMplsLabel
gmplsPortWavelengthLabel(2) gmplsLabelPortWavelength
gmplsFreeformLabel(3) gmplsLabelFreeform
gmplsSonetLabel(4) gmplsLabelSonetSdhSignalIndex
gmplsLabelSdhVc
gmplsLabelSdhVcBranch
gmplsLabelSonetSdhBranch
gmplsLabelSonetSdhGroupBranch
gmplsSdhLabel(5) gmplsLabelSonetSdhSignalIndex
gmplsLabelSdhVc
gmplsLabelSdhVcBranch
gmplsLabelSonetSdhBranch
gmplsLabelSonetSdhGroupBranch
gmplsWavebandLabel(6) gmplsLabelWavebandId
gmplsLabelWavebandStart
gmplsLabelWavebandEnd"
::= { gmplsLabelEntry 17 }
gmplsLabelGroups
OBJECT IDENTIFIER ::= { gmplsLabelConformance 1 }
Nadeau & Farrel Standards Track [Page 31]
RFC 4803 GMPLS LSR MIB February 2007
gmplsLabelCompliances
OBJECT IDENTIFIER ::= { gmplsLabelConformance 2 }
gmplsLabelModuleReadOnlyCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"Compliance requirement for implementations that only provide
read-only support for GMPLS-LABEL-STD-MIB. Such devices can then
be monitored but cannot be configured using this MIB module."
MODULE -- this module
-- The mandatory groups have to be implemented by LSRs claiming
-- support for this MIB module. This MIB module is, however, not
-- mandatory for a working implementation of a GMPLS LSR with full
-- MIB support if the GMPLS Labels in use can be represented within
-- a 32-bit quantity.
MANDATORY-GROUPS {
gmplsLabelTableGroup
}
GROUP gmplsLabelPacketGroup
DESCRIPTION
"This group extends gmplsLabelTableGroup for implementations that
support Packet Labels. It is optional for implementations that
do not support Packet Labels."
GROUP gmplsLabelPortWavelengthGroup
DESCRIPTION
"This group extends gmplsLabelTableGroup for implementations that
support Port and Wavelength Labels. It is optional for
implementations that do not support Wavelength Labels."
GROUP gmplsLabelFreeformGroup
DESCRIPTION
"This group extends gmplsLabelTableGroup for implementations that
support Freeform Labels. It is optional for implementations that
do not support Freeform Labels."
GROUP gmplsLabelSonetSdhGroup
DESCRIPTION
"This group extends gmplsLabelTableGroup for implementations that
support SONET or SDH Labels. It is optional for implementations
that do not support SONET or SDH Labels."
GROUP gmplsLabelWavebandGroup
DESCRIPTION
Nadeau & Farrel Standards Track [Page 32]
RFC 4803 GMPLS LSR MIB February 2007
"This group extends gmplsLabelTableGroup for implementations that
support Waveband Labels. It is optional for implementations that
do not support Waveband Labels."
OBJECT gmplsLabelType
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT gmplsLabelMplsLabel
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT gmplsLabelPortWavelength
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT gmplsLabelFreeform
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT gmplsLabelSonetSdhSignalIndex
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT gmplsLabelSdhVc
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT gmplsLabelSdhVcBranch
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT gmplsLabelSonetSdhBranch
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT gmplsLabelSonetSdhGroupBranch
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
Nadeau & Farrel Standards Track [Page 33]
RFC 4803 GMPLS LSR MIB February 2007
OBJECT gmplsLabelWavebandId
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT gmplsLabelWavebandStart
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT gmplsLabelWavebandEnd
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT gmplsLabelStorageType
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT gmplsLabelRowStatus
SYNTAX RowStatus { active(1) }
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required, and active(1) is
the only status that needs to be supported."
::= { gmplsLabelCompliances 1 }
gmplsLabelModuleFullCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"Compliance statement for agents that support the complete
GMPLS-LABEL-STD-MIB module.
The mandatory groups have to be implemented by GMPLS LSRs
claiming support for this MIB module. This MIB module is,
however, not mandatory for a working implementation of a GMPLS
LSR with full MIB support if the GMPLS Labels in use can be
represented within a 32-bit quantity."
MODULE -- this module
MANDATORY-GROUPS {
gmplsLabelTableGroup
}
::= { gmplsLabelCompliances 2 }
Nadeau & Farrel Standards Track [Page 34]
RFC 4803 GMPLS LSR MIB February 2007
gmplsLabelTableGroup OBJECT-GROUP
OBJECTS {
gmplsLabelIndexNext,
gmplsLabelType,
gmplsLabelStorageType,
gmplsLabelRowStatus
}
STATUS current
DESCRIPTION
"Necessary, but not sufficient, set of objects to implement label
table support. In addition, depending on the type of labels
supported, the following other groups defined below are
mandatory:
gmplsLabelWavebandGroup and/or
gmplsLabelPacketGroup and/or
gmplsLabelPortWavelengthGroup and/or
gmplsLabelFreeformGroup and/or
gmplsLabelSonetSdhGroup."
::= { gmplsLabelGroups 1 }
gmplsLabelPacketGroup OBJECT-GROUP
OBJECTS {
gmplsLabelMplsLabel
}
STATUS current
DESCRIPTION
"Object needed to implement Packet (MPLS) Labels."
::= { gmplsLabelGroups 2 }
gmplsLabelPortWavelengthGroup OBJECT-GROUP
OBJECTS {
gmplsLabelPortWavelength
}
STATUS current
DESCRIPTION
"Object needed to implement Port and Wavelength Labels."
::= { gmplsLabelGroups 3 }
gmplsLabelFreeformGroup OBJECT-GROUP
OBJECTS {
gmplsLabelFreeform
}
STATUS current
DESCRIPTION
"Object needed to implement Freeform Labels."
::= { gmplsLabelGroups 4 }
Nadeau & Farrel Standards Track [Page 35]
RFC 4803 GMPLS LSR MIB February 2007
gmplsLabelSonetSdhGroup OBJECT-GROUP
OBJECTS {
gmplsLabelSonetSdhSignalIndex,
gmplsLabelSdhVc,
gmplsLabelSdhVcBranch,
gmplsLabelSonetSdhBranch,
gmplsLabelSonetSdhGroupBranch
}
STATUS current
DESCRIPTION
"Objects needed to implement SONET and SDH Labels."
::= { gmplsLabelGroups 5 }
gmplsLabelWavebandGroup OBJECT-GROUP
OBJECTS {
gmplsLabelWavebandId,
gmplsLabelWavebandStart,
gmplsLabelWavebandEnd
}
STATUS current
DESCRIPTION
"Objects needed to implement Waveband Labels."
::= { gmplsLabelGroups 6 }
END
9. Security Considerations
It is clear that the MIB modules described in this document in
association with MPLS-LSR-STD-MIB [RFC3813] are potentially useful
for monitoring of GMPLS LSRs. These MIB modules can also be used for
configuration of certain objects, and anything that can be configured
can be incorrectly configured, with potentially disastrous results.
There are a number of management objects defined in these MIB modules
with a MAX-ACCESS clause of read-write and/or read-create. Such
objects may be considered sensitive or vulnerable in some network
environments. The support for SET operations in a non-secure
environment without proper protection can have a negative effect on
network operations. These are the tables and objects and their
sensitivity/vulnerability:
o the gmplsInterfaceTable, gmplsInSegmentTable,
gmplsOutSegmentTable, and gmplsLabelTable collectively contain
objects to provision GMPLS interfaces, LSPs, and their associated
parameters on a Label Switching Router (LSR). Unauthorized write
access to objects in these tables could result in disruption of
Nadeau & Farrel Standards Track [Page 36]
RFC 4803 GMPLS LSR MIB February 2007
traffic on the network. This is especially true if an LSP has
already been established.
Some of the readable objects in these MIB modules (i.e., objects with
a MAX-ACCESS other than not-accessible) may be considered sensitive
or vulnerable in some network environments. It is thus important to
control even GET and/or NOTIFY access to these objects and possibly
to even encrypt the values of these objects when sending them over
the network via SNMP. These are the tables and objects and their
sensitivity/vulnerability:
o the gmplsInterfaceTable, gmplsInSegmentTable,
gmplsOutSegmentTable, and gmplsLabelTable collectively show the
LSP network topology and its capabilities. If an administrator
does not want to reveal this information, then these tables should
be considered sensitive/vulnerable.
SNMP versions prior to SNMPv3 did not include adequate security.
Even if the network itself is secure (for example by using IPsec),
even then, there is no control as to who on the secure network is
allowed to access and GET/SET (read/change/create/delete) the objects
in these MIB modules.
It is RECOMMENDED that implementers consider the security features as
provided by the SNMPv3 framework (see [RFC3410], section 8),
including full support for the SNMPv3 cryptographic mechanisms (for
authentication and privacy).
Further, deployment of SNMP versions prior to SNMPv3 is NOT
RECOMMENDED. Instead, it is RECOMMENDED to deploy SNMPv3 and to
enable cryptographic security. It is then a customer/operator
responsibility to ensure that the SNMP entity giving access to an
instance of this MIB module, is properly configured to give access to
the objects only to those principals (users) that have legitimate
rights to indeed GET or SET (change/create/delete) them.
10. Acknowledgments
This document is a product of the CCAMP Working Group.
This document extends the MIB tables in [RFC3813]. The authors would
like to express their gratitude to all those who worked on that
earlier MIB document.
The authors would like to express their thanks to Dan Joyle for his
careful review and comments on early versions of the label table.
Special thanks to Joan Cucchiara and Len Nieman for their help with
Nadeau & Farrel Standards Track [Page 37]
RFC 4803 GMPLS LSR MIB February 2007
compilation issues. Lars Eggert, Tom Petch, Dan Romascanu, and Bert
Wijnen provided useful input in the final stages of review.
Joan Cucchiara provided a helpful and very thorough MIB Doctor
review.
11. IANA Considerations
IANA has rooted MIB objects in the two MIB modules contained in this
document under the mplsStdMIB subtree.
IANA has made the following assignments in the "NETWORK MANAGEMENT
PARAMETERS" registry located at http://www.iana.org/assignments/
smi-numbers in table:
...mib-2.transmission.mplsStdMIB (1.3.6.1.2.1.10.166)
Decimal Name References
------- ----- ----------
15 GMPLS-LSR-STD-MIB [RFC4803]
16 GMPLS-LABEL-STD-MIB [RFC4803]
In the future, GMPLS-related standards-track MIB modules should be
rooted under the mplsStdMIB (sic) subtree. IANA has been requested
to manage that namespace in the SMI Numbers registry [RFC3811]. New
assignments can only be made via a Standards Action as specified in
[RFC2434].
12. References
12.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC2434] Narten, T. and H. Alvestrand, "Guidelines for Writing an
IANA Considerations Section in RFCs", BCP 26, RFC 2434,
October 1998.
[RFC2578] McCloghrie, K., Perkins, D., and J. Schoenwaelder,
"Structure of Management Information Version 2 (SMIv2)",
STD 58, RFC 2578, April 1999.
[RFC2579] McCloghrie, K., Perkins, D., and J. Schoenwaelder,
"Textual Conventions for SMIv2", STD 58, RFC 2579, April
1999.
Nadeau & Farrel Standards Track [Page 38]
RFC 4803 GMPLS LSR MIB February 2007
[RFC2580] McCloghrie, K., Perkins, D., and J. Schoenwaelder,
"Conformance Statements for SMIv2", STD 58, RFC 2580,
April 1999.
[RFC2863] McCloghrie, K. and F. Kastenholz, "The Interfaces Group
MIB", RFC 2863, June 2000.
[RFC3031] Rosen, E., Viswanathan, A., and R. Callon,
"Multiprotocol Label Switching Architecture", RFC 3031,
January 2001.
[RFC3032] Rosen, E., Tappan, D., Fedorkow, G., Rekhter, Y.,
Farinacci, D., Li, T., and A. Conta, "MPLS Label Stack
Encoding", RFC 3032, January 2001.
[RFC3209] Awduche, D., Berger, L., Gan, D., Li, T., Srinivasan,
V., and G. Swallow, "RSVP-TE: Extensions to RSVP for LSP
Tunnels", RFC 3209, December 2001.
[RFC3289] Baker, F., Chan, K., and A. Smith, "Management
Information Base for the Differentiated Services
Architecture", RFC 3289, May 2002.
[RFC3443] Agarwal, P. and B. Akyol, "Time To Live (TTL) Processing
in Multi-Protocol Label Switching (MPLS) Networks", RFC
3443, January 2003.
[RFC3471] Berger, L., "Generalized Multi-Protocol Label Switching
(GMPLS) Signaling Functional Description", RFC 3471,
January 2003.
[RFC3473] Berger, L., "Generalized Multi-Protocol Label Switching
(GMPLS) Signaling Resource ReserVation Protocol-Traffic
Engineering (RSVP-TE) Extensions", RFC 3473, January
2003.
[RFC3811] Nadeau, T. and J. Cucchiara, "Definitions of Textual
Conventions (TCs) for Multiprotocol Label Switching
(MPLS) Management", RFC 3811, June 2004.
[RFC3813] Srinivasan, C., Viswanathan, A., and T. Nadeau,
"Multiprotocol Label Switching (MPLS) Label Switching
Router (LSR) Management Information Base (MIB)", RFC
3813, June 2004.
[RFC3945] Mannie, E., "Generalized Multi-Protocol Label Switching
(GMPLS) Architecture", RFC 3945, October 2004.
Nadeau & Farrel Standards Track [Page 39]
RFC 4803 GMPLS LSR MIB February 2007
[RFC4606] Mannie, E. and D. Papadimitriou, "Generalized Multi-
Protocol Label Switching (GMPLS) Extensions for
Synchronous Optical Network (SONET) and Synchronous
Digital Hierarchy (SDH) Control", RFC 4606, August 2006.
[RFC4801] Nadeau, T., Ed. and A. Farrel, Ed., "Definitions of
Textual Conventions for Multiprotocol Label Switching
(MPLS) Management", RFC 4801, February 2007.
[RFC4802] Nadeau, T., Ed. and A. Farrel, Ed., "Generalized
Multiprotocol Label Switching (GMPLS) Traffic
Engineering Management Information Base", RFC 4802,
February 2007.
12.2. Informative References
[RFC3410] Case, J., Mundy, R., Partain, D., and B. Stewart,
"Introduction and Applicability Statements for
Internet-Standard Management Framework", RFC 3410,
December 2002.
[RFC3468] Andersson, L. and G. Swallow, "The Multiprotocol Label
Switching (MPLS) Working Group decision on MPLS
signaling protocols", RFC 3468, February 2003.
[RFC3472] Ashwood-Smith, P. and L. Berger, "Generalized Multi-
Protocol Label Switching (GMPLS) Signaling Constraint-
based Routed Label Distribution Protocol (CR-LDP)
Extensions", RFC 3472, January 2003.
[RFC3812] Srinivasan, C., Viswanathan, A., and T. Nadeau,
"Multiprotocol Label Switching (MPLS) Traffic
Engineering (TE) Management Information Base (MIB)", RFC
3812, June 2004.
Nadeau & Farrel Standards Track [Page 40]
RFC 4803 GMPLS LSR MIB February 2007
Contact Information
Thomas D. Nadeau
Cisco Systems, Inc.
1414 Massachusetts Ave.
Boxborough, MA 01719
EMail: tnadeau@cisco.com
Adrian Farrel
Old Dog Consulting
Phone: +44-(0)-1978-860944
EMail: adrian@olddog.co.uk
Cheenu Srinivasan
Bloomberg L.P.
731 Lexington Ave.
New York, NY 10022
Phone: +1-212-617-3682
EMail: cheenu@bloomberg.net
Tim Hall
Data Connection Ltd.
100 Church Street
Enfield, Middlesex, EN2 6BQ, UK
Phone: +44 20 8366 1177
EMail: tim.hall@dataconnection.com
Ed Harrison
Data Connection Ltd.
100 Church Street
Enfield, Middlesex, EN2 6BQ, UK
Phone: +44 20 8366 1177
EMail: ed.harrison@dataconnection.com
Nadeau & Farrel Standards Track [Page 41]
RFC 4803 GMPLS LSR MIB February 2007
Full Copyright Statement
Copyright (C) The IETF Trust (2007).
This document is subject to the rights, licenses and restrictions
contained in BCP 78, and except as set forth therein, the authors
retain all their rights.
This document and the information contained herein are provided on an
"AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE IETF TRUST AND
THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS
OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF
THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Intellectual Property
The IETF takes no position regarding the validity or scope of any
Intellectual Property Rights or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; nor does it represent that it has
made any independent effort to identify any such rights. Information
on the procedures with respect to rights in RFC documents can be
found in BCP 78 and BCP 79.
Copies of IPR disclosures made to the IETF Secretariat and any
assurances of licenses to be made available, or the result of an
attempt made to obtain a general license or permission for the use of
such proprietary rights by implementers or users of this
specification can be obtained from the IETF on-line IPR repository at
http://www.ietf.org/ipr.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights that may cover technology that may be required to implement
this standard. Please address the information to the IETF at
ietf-ipr@ietf.org.
Acknowledgement
Funding for the RFC Editor function is currently provided by the
Internet Society.
Nadeau & Farrel Standards Track [Page 42]