<- RFC Index (5501..5600)
RFC 5525
Network Working Group T. Dreibholz
Request for Comments: 5525 University of Duisburg-Essen
Category: Experimental J. Mulik
Delaware State University
April 2009
Reliable Server Pooling MIB Module Definition
Status of This Memo
This memo defines an Experimental Protocol for the Internet
community. It does not specify an Internet standard of any kind.
Discussion and suggestions for improvement are requested.
Distribution of this memo is unlimited.
Copyright Notice
Copyright (c) 2009 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents in effect on the date of
publication of this document (http://trustee.ietf.org/license-info).
Please review these documents carefully, as they describe your rights
and restrictions with respect to this document.
Abstract
Reliable Server Pooling (RSerPool) is a framework to provide reliable
server pooling. The RSerPool framework consists of two protocols:
ASAP (Aggregate Server Access Protocol) and ENRP (Endpoint
Handlespace Redundancy Protocol). This document defines an SMIv2-
compliant (Structure of Management Information Version 2) Management
Information Base (MIB) module providing access to managed objects in
an RSerPool implementation.
Dreibholz & Mulik Experimental [Page 1]
RFC 5525 RSerPool MIB Module April 2009
Table of Contents
1. Introduction ....................................................2
2. The Reliable Server Pooling (RSerPool) Framework ................2
3. Conventions .....................................................2
4. The Internet-Standard Management Framework ......................2
5. Structure of the MIB ............................................3
5.1. Access to Managed Objects on ENRP Servers .................10
5.2. Access to Managed Objects on Pool Elements ................10
5.3. Access to Managed Objects on Pool Users ...................11
5.4. Persistency Behavior ......................................11
6. Definitions ....................................................11
7. Operational Considerations .....................................42
8. Security Considerations ........................................42
9. IANA Considerations ............................................43
10. Acknowledgments ...............................................43
11. References ....................................................44
11.1. Normative References .....................................44
11.2. Informative References ...................................44
1. Introduction
This memo defines a Management Information Base (MIB) module that
describes managed objects for RSerPool implementations.
2. The Reliable Server Pooling (RSerPool) Framework
For a detailed overview of the documents that describe the current
Reliable Server Pooling (RSerPool) framework, please refer to
[RFC3237], [RFC5351], [RFC5352], [RFC5353], [RFC5354], [RFC5355], and
[RFC5356]. A more informal introduction can be found at
[RSerPoolPage] as well as in [Dre2006], [LCN2005], and [IJHIT2008].
3. Conventions
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in [RFC2119].
4. The Internet-Standard Management Framework
For a detailed overview of the documents that describe the current
Internet-Standard Management Framework, please refer to section 7 of
RFC 3410 [RFC3410].
Managed objects are accessed via a virtual information store, termed
the Management Information Base or MIB. MIB objects are generally
accessed through the Simple Network Management Protocol (SNMP).
Dreibholz & Mulik Experimental [Page 2]
RFC 5525 RSerPool MIB Module April 2009
Objects in the MIB are defined using the mechanisms defined in the
Structure of Management Information (SMI). This memo specifies a MIB
module that is compliant to the SMIv2, which is described in STD 58,
RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC 2580
[RFC2580]. The textual conventions are compliant to RFC 4001
[RFC4001].
5. Structure of the MIB
The following diagram illustrates the structure of the MIB.
Structure of MIB
+--rserpoolMIB(125)
|
+--rserpoolMIBObjects(1)
| |
| +--rserpoolENRPServers(1)
| | |
| | +--rserpoolENRPTable(1)
| | | |
| | | +--rserpoolENRPEntry(1)
| | | | Index: rserpoolENRPIndex
| | | |
| | | +-- ---- Unsigned rserpoolENRPIndex(1)
| | | | Range: 1..4294967295
| | | +-- -R-- String rserpoolENRPOperationScope(2)
| | | | Textual Conv.: RSerPoolOperationScopeTC
| | | | Size: 0..65535
| | | +-- -R-- Unsigned rserpoolENRPIdentifier(3)
| | | | Textual Conv.: RSerPoolENRPServerIdentifierTC
| | | | Range: 1..4294967295
| | | +-- -RW- String rserpoolENRPDescription(4)
| | | | Size: 0..255
| | | +-- -R-- TimeTicks rserpoolENRPUptime(5)
| | | +-- -R-- Unsigned rserpoolENRPPort(6)
| | | | Textual Conv.: InetPortNumber
| | | | Range: 0..65535
| | | +-- -R-- Unsigned rserpoolENRPASAPAnnouncePort(7)
| | | | Textual Conv.: InetPortNumber
| | | | Range: 0..65535
| | | +-- -R-- EnumVal rserpoolENRPASAPAnnounceAddrType(8)
| | | | Textual Conv.: InetAddressType
| | | | Values: ipv4(1), ipv6(2)
| | | +-- -R-- String rserpoolENRPASAPAnnounceAddr(9)
| | | | Textual Conv.: InetAddress
| | | | Size: 4 | 16
Dreibholz & Mulik Experimental [Page 3]
RFC 5525 RSerPool MIB Module April 2009
| | | +-- -R-- Unsigned rserpoolENRPENRPAnnouncePort(10)
| | | | Textual Conv.: InetPortNumber
| | | | Range: 0..65535
| | | +-- -R-- EnumVal rserpoolENRPENRPAnnounceAddrType(11)
| | | | Textual Conv.: InetAddressType
| | | | Values: ipv4(1), ipv6(2)
| | | +-- -R-- String rserpoolENRPENRPAnnounceAddr(12)
| | | Textual Conv.: InetAddress
| | | Size: 4 | 16
| | |
| | +--rserpoolENRPPoolTable(3)
| | | |
| | | +--rserpoolENRPPoolEntry(1)
| | | | Index: rserpoolENRPIndex, rserpoolENRPPoolIndex
| | | |
| | | +-- ---- Unsigned rserpoolENRPPoolIndex(1)
| | | | Range: 1..4294967295
| | | +-- -R-- String rserpoolENRPPoolHandle(2)
| | | Textual Conv.: RSerPoolPoolHandleTC
| | | Size: 0..65535
| | |
| | +--rserpoolENRPPoolElementTable(4)
| | | |
| | | +--rserpoolENRPPoolElementEntry(1)
| | | | Index: rserpoolENRPIndex, rserpoolENRPPoolIndex,
| | | | rserpoolENRPPoolElementIndex
| | | |
| | | +-- ---- Unsigned rserpoolENRPPoolElementIndex(1)
| | | | Range: 1..4294967295
| | | +-- -R-- Unsigned rserpoolENRPPoolElementID(2)
| | | | Textual Conv.: RserpoolPoolElementIdentifierTC
| | | | Range: 1..4294967295
| | | +-- -R-- Unsigned rserpoolENRPASAPTransportPort(3)
| | | | Textual Conv.: InetPortNumber
| | | | Range: 0..65535
| | | +-- -R-- Unsigned rserpoolENRPUserTransportProto(4)
| | | | Range: 0..255
| | | +-- -R-- Unsigned rserpoolENRPUserTransportPort(5)
| | | | Textual Conv.: InetPortNumber
| | | | Range: 0..65535
| | | +-- -R-- EnumVal rserpoolENRPUserTransportUse(6)
| | | | Textual Conv.: RSerPoolTransportUseTypeTC
| | | | Values: dataOnly(0), dataPlusControl(1)
| | | +-- -R-- Unsigned rserpoolENRPPolicyID(7)
| | | | Textual Conv.: RSerPoolPolicyIdentifierTC
| | | | Range: 1..4294967295
| | | +-- -R-- String rserpoolENRPPolicyDescription(8)
| | | | Size: 0..255
Dreibholz & Mulik Experimental [Page 4]
RFC 5525 RSerPool MIB Module April 2009
| | | +-- -R-- Unsigned rserpoolENRPPolicyWeight(9)
| | | | Textual Conv.: RSerPoolPolicyWeightTC
| | | | Range: 0..4294967295
| | | +-- -R-- Unsigned rserpoolENRPPolicyLoad(10)
| | | | Textual Conv.: RSerPoolPolicyLoadTC
| | | | Range: 0..4294967295
| | | +-- -R-- Unsigned rserpoolENRPPolicyLoadDeg(11)
| | | | Textual Conv.: RSerPoolPolicyLoadTC
| | | | Range: 0..4294967295
| | | +-- -R-- TimeTicks rserpoolENRPRegistrationLife(12)
| | | +-- -R-- Unsigned rserpoolENRPHomeENRPServer(13)
| | | Textual Conv.: RSerPoolENRPServerIdentifierTC
| | | Range: 1..4294967295
| | |
| | +--rserpoolENRPASAPAddrTable(5)
| | | |
| | | +--rserpoolENRPASAPAddrTableEntry(1)
| | | | Index: rserpoolENRPIndex, rserpoolENRPPoolIndex,
| | | | rserpoolENRPPoolElementIndex,
| | | | rserpoolENRPASAPAddrTableIndex
| | | |
| | | +-- ---- Unsigned rserpoolENRPASAPAddrTableIndex(1)
| | | | Range: 1..4294967295
| | | +-- -R-- EnumVal rserpoolENRPASAPL3Type(2)
| | | | Textual Conv.: InetAddressType
| | | | Values: ipv4(1), ipv6(2)
| | | +-- -R-- String rserpoolENRPASAPL3Addr(3)
| | | Textual Conv.: InetAddress
| | | Size: 4 | 16
| | |
| | +--rserpoolENRPUserAddrTable(6)
| | | |
| | | +--rserpoolENRPUserAddrTableEntry(1)
| | | | Index: rserpoolENRPIndex, rserpoolENRPPoolIndex,
| | | | rserpoolENRPPoolElementIndex,
| | | | rserpoolENRPUserAddrTableIndex
| | | |
| | | +-- ---- Unsigned rserpoolENRPUserAddrTableIndex(1)
| | | | Range: 1..4294967295
| | | +-- -R-- EnumVal rserpoolENRPUserL3Type(2)
| | | | Textual Conv.: InetAddressType
| | | | Values: unknown(0), ipv4(1), ipv6(2)
| | | +-- -R-- String rserpoolENRPUserL3Addr(3)
| | | | Textual Conv.: InetAddress
| | | | Size: 0 | 4 | 16
| | | +-- -R-- String rserpoolENRPUserL3Opaque(4)
| | | Textual Conv.: RSerPoolOpaqueAddressTC
| | | Size: 0..65535
Dreibholz & Mulik Experimental [Page 5]
RFC 5525 RSerPool MIB Module April 2009
| | |
| | +--rserpoolENRPENRPAddrTable(7)
| | | |
| | | +--rserpoolENRPENRPAddrTableEntry(1)
| | | | Index: rserpoolENRPIndex,
| | | | rserpoolENRPENRPAddrTableIndex
| | | |
| | | +-- ---- Unsigned rserpoolENRPENRPAddrTableIndex(1)
| | | | Range: 1..4294967295
| | | +-- -R-- EnumVal rserpoolENRPENRPL3Type(2)
| | | | Textual Conv.: InetAddressType
| | | | Values: ipv4(1), ipv6(2)
| | | +-- -R-- String rserpoolENRPENRPL3Addr(3)
| | | Textual Conv.: InetAddress
| | | Size: 4 | 16
| | |
| | +--rserpoolENRPPeerTable(8)
| | | |
| | | +--rserpoolENRPPeerEntry(1)
| | | | Index: rserpoolENRPPeerIndex
| | | |
| | | +-- ---- Unsigned rserpoolENRPPeerIndex(1)
| | | | Range: 1..4294967295
| | | +-- -R-- Unsigned rserpoolENRPPeerIdentifier(2)
| | | | Textual Conv.: RSerPoolENRPServerIdentifierTC
| | | | Range: 1..4294967295
| | | +-- -R-- Unsigned rserpoolENRPPeerPort(3)
| | | | Textual Conv.: InetPortNumber
| | | | Range: 0..65535
| | | +-- -R-- TimeTicks rserpoolENRPPeerLastHeard(4)
| | |
| | +--rserpoolENRPPeerAddrTable(9)
| | |
| | +--rserpoolENRPPeerAddrTableEntry(1)
| | | Index: rserpoolENRPPeerIndex,
| | | | rserpoolENRPPeerAddrTableIndex
| | |
| | +-- ---- Unsigned rserpoolENRPPeerAddrTableIndex(1)
| | | Range: 1..4294967295
| | +-- -R-- EnumVal rserpoolENRPPeerL3Type(2)
| | | Textual Conv.: InetAddressType
| | | Values: ipv4(1), ipv6(2)
| | +-- -R-- String rserpoolENRPPeerL3Addr(3)
| | Textual Conv.: InetAddress
| | Size: 4 | 16
| |
| +--rserpoolPoolElements(2)
| | |
Dreibholz & Mulik Experimental [Page 6]
RFC 5525 RSerPool MIB Module April 2009
| | +--rserpoolPETable(1)
| | | |
| | | +--rserpoolPEEntry(1)
| | | | Index: rserpoolPEIndex
| | | |
| | | +-- ---- Unsigned rserpoolPEIndex(1)
| | | | Range: 1..4294967295
| | | +-- -R-- String rserpoolPEOperationScope(2)
| | | | Textual Conv.: RSerPoolOperationScopeTC
| | | | Size: 0..65535
| | | +-- -RW- String rserpoolPEPoolHandle(3)
| | | | Textual Conv.: RSerPoolPoolHandleTC
| | | | Size: 0..65535
| | | +-- -R-- Unsigned rserpoolPEIdentifier(4)
| | | | Textual Conv.: RserpoolPoolElementIdentifierTC
| | | | Range: 1..4294967295
| | | +-- -RW- String rserpoolPEDescription(5)
| | | | Size: 0..255
| | | +-- -R-- TimeTicks rserpoolPEUptime(6)
| | | +-- -R-- Unsigned rserpoolPEASAPTransportPort(7)
| | | | Textual Conv.: InetPortNumber
| | | | Range: 0..65535
| | | +-- -R-- Unsigned rserpoolPEUserTransportProto(8)
| | | | Range: 0..255
| | | +-- -R-- Unsigned rserpoolPEUserTransportPort(9)
| | | | Textual Conv.: InetPortNumber
| | | | Range: 0..65535
| | | +-- -R-- EnumVal rserpoolPEUserTransportUse(10)
| | | | Textual Conv.: RSerPoolTransportUseTypeTC
| | | | Values: dataOnly(0), dataPlusControl(1)
| | | +-- -RW- Unsigned rserpoolPEPolicyID(11)
| | | | Textual Conv.: RSerPoolPolicyIdentifierTC
| | | | Range: 1..4294967295
| | | +-- -RW- String rserpoolPEPolicyDescription(12)
| | | | Size: 0..255
| | | +-- -RW- Unsigned rserpoolPEPolicyWeight(13)
| | | | Textual Conv.: RSerPoolPolicyWeightTC
| | | | Range: 0..4294967295
| | | +-- -R-- Unsigned rserpoolPEPolicyLoad(14)
| | | | Textual Conv.: RSerPoolPolicyLoadTC
| | | | Range: 0..4294967295
| | | +-- -RW- Unsigned rserpoolPEPolicyLoadDeg(15)
| | | | Textual Conv.: RSerPoolPolicyLoadTC
| | | | Range: 0..4294967295
| | | +-- -RW- TimeTicks rserpoolPERegistrationLife(16)
| | | +-- -R-- Unsigned rserpoolPEHomeENRPServer(17)
| | | Textual Conv.: RSerPoolENRPServerIdentifierTC
| | | Range: 1..4294967295
Dreibholz & Mulik Experimental [Page 7]
RFC 5525 RSerPool MIB Module April 2009
| | |
| | +--rserpoolPEASAPAddrTable(2)
| | | |
| | | +--rserpoolPEASAPAddrTableEntry(1)
| | | | Index: rserpoolPEIndex, rserpoolPEASAPAddrTableIndex
| | | |
| | | +-- ---- Unsigned rserpoolPEASAPAddrTableIndex(1)
| | | | Range: 1..4294967295
| | | +-- -R-- EnumVal rserpoolPEASAPL3Type(2)
| | | | Textual Conv.: InetAddressType
| | | | Values: ipv4(1), ipv6(2)
| | | +-- -R-- String rserpoolPEASAPL3Addr(3)
| | | Textual Conv.: InetAddress
| | | Size: 4 | 16
| | |
| | +--rserpoolPEUserAddrTable(6)
| | |
| | +--rserpoolPEUserAddrTableEntry(1)
| | | Index: rserpoolPEIndex, rserpoolPEUserAddrTableIndex
| | |
| | +-- ---- Unsigned rserpoolPEUserAddrTableIndex(1)
| | | Range: 1..4294967295
| | +-- -R-- EnumVal rserpoolPEUserL3Type(2)
| | | Textual Conv.: InetAddressType
| | | Values: unknown(0), ipv4(1), ipv6(2)
| | +-- -R-- String rserpoolPEUserL3Addr(3)
| | | Textual Conv.: InetAddress
| | | Size: 0 | 4 | 16
| | +-- -R-- String rserpoolPEUserL3Opaque(4)
| | Textual Conv.: RSerPoolOpaqueAddressTC
| | Size: 0..65535
| |
| +--rserpoolPoolUsers(3)
| |
| +--rserpoolPUTable(1)
| |
| +--rserpoolPUEntry(1)
| | Index: rserpoolPUIndex
| |
| +-- ---- Unsigned rserpoolPUIndex(1)
| | Range: 1..4294967295
| +-- -R-- String rserpoolPUOperationScope(2)
| | Textual Conv.: RSerPoolOperationScopeTC
| | Size: 0..65535
| +-- -RW- String rserpoolPUPoolHandle(3)
| | Textual Conv.: RSerPoolPoolHandleTC
| | Size: 0..65535
| +-- -RW- String rserpoolPUDescription(4)
Dreibholz & Mulik Experimental [Page 8]
RFC 5525 RSerPool MIB Module April 2009
| | Size: 0..255
| +-- -R-- TimeTicks rserpoolPUUptime(5)
|
+--rserpoolMIBConformance(2)
|
+--rserpoolMIBCompliances(1)
| |
| +--rserpoolMIBCompliance(1)
|
+--rserpoolMIBGroups(2)
|
+--rserpoolENRPGroup(1)
+--rserpoolPEGroup(2)
+--rserpoolPUGroup(3)
As the figure shows, the MIB consists of three main branches:
"rserpoolENRPServers", "rserpoolPoolElements", and
"rserpoolPoolUsers". The first branch, "rserpoolENRPServers", is
used to access managed objects in the set of ENRP servers running on
a given host. While it is assumed that it does not make much sense
to run multiple ENRP servers for the same operation scope on one
host, running multiple ENRP servers for different operation scopes is
very likely when the ENRP server processes run on routers.
Therefore, the MIB has to be able to manage multiple ENRP servers on
the same host.
"rserpoolPoolElements" is used to access managed objects in the set
of pool elements that are running on a given host.
The third branch, "rserpoolPoolUsers", is used to access managed
objects in the set of pool users that are running on a given host.
Note: "rserpoolENRPServers" is filled on hosts running ENRP server
instances, "rserpoolPoolElements" is filled on hosts running pool
element instances, and "rserpoolPoolUsers" is filled on hosts running
pool user instances. Of course, multiple different components may
run on the same host, which leads to filling of multiple different
branches.
In fact, the structure of the three branches is very similar.
Because the other two branches are so similar, we describe only the
first branch in detail, and provide a summary description of the
second and third branch. We now proceed with a description of the
branches.
Dreibholz & Mulik Experimental [Page 9]
RFC 5525 RSerPool MIB Module April 2009
5.1. Access to Managed Objects on ENRP Servers
The first branch describes managed objects at a set of ENRP servers.
Any given ENRP server of this set will, at a certain moment in time,
have registration information for a set of active pools. Each of
these pools in turn may have a list of pool elements that are
registered under that pool. To allow this information to be
retrieved via SNMP, the ERNP server branch of the RSerPool MIB uses
the table-in-table technique described in [SNMPMIBS].
Specifically, the ENRP servers branch creates four levels of nesting,
as indicated in the following diagram:
Nesting of the ENRP Server Branch
Nesting Structure:
Level 1: rserpoolENRPTable
Level 2: rserpoolENRPPoolTable
Level 3: rserpoolENRPPoolElementTable
Level 4: rserpoolENRPASAPAddrTable
rserpoolENRPUserAddrTable
Level 2: rserpoolENRPENRPAddrTable
Level 2: rserpoolENRPPeerTable
Level 3: rserpoolENRPPeerAddrTable
5.2. Access to Managed Objects on Pool Elements
The construction of the Pool Elements branch is very similar to the
pool elements table of the ENRP servers branch. But instead of
grouping the pool elements into pools (which does not make sense
here), the pool elements table is the top of the hierarchy, and each
pool element entry specifies its operation scope and pool handle.
That is, the nesting structure is as follows:
Nesting of the Pool Elements Branch
Level 1: rserpoolPETable
Level 2: rserpoolPEASAPAddrTable
rserpoolPEUserAddrTable
Dreibholz & Mulik Experimental [Page 10]
RFC 5525 RSerPool MIB Module April 2009
5.3. Access to Managed Objects on Pool Users
For the Pool Users branch, it is only necessary to list the pool user
instances, including their operation scope and pool handle.
5.4. Persistency Behavior
Upon changes of writable objects, an implementation SHOULD store the
new values in a persistent manner if it has the capability to do
this. An implementation SHOULD use these stored values upon reset or
reinitialization.
6. Definitions
RSERPOOL-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE, experimental,
TimeTicks, Unsigned32
FROM SNMPv2-SMI
TEXTUAL-CONVENTION
FROM SNMPv2-TC
MODULE-COMPLIANCE, OBJECT-GROUP
FROM SNMPv2-CONF
InetAddressType, InetAddress, InetPortNumber
FROM INET-ADDRESS-MIB;
-- ## Module definition ###########################################
rserpoolMIB MODULE-IDENTITY
LAST-UPDATED
"200904070000Z" -- April 07, 2009
ORGANIZATION
"IEM-TdR, UNIVERSITY OF DUISBURG-ESSEN"
CONTACT-INFO
" THOMAS-DREIBHOLZ
Postal: University of Duisburg-Essen
Institute for Experimental Mathematics
Ellernstrasse 29
D-45326 Essen
Germany
Phone: +49-201-183-7637
Fax: +49-201-183-7673
Email: dreibh@iem.uni-due.de
Dreibholz & Mulik Experimental [Page 11]
RFC 5525 RSerPool MIB Module April 2009
JAIWANT-MULIK
Postal: Delaware State University
CIS Department
1200 N. DuPont Hw
Dover, DE
USA 19904
Phone: +1-302-857-7910
Fax: +1-302-857-6552
Email: jaiwant@mulik.com"
DESCRIPTION
"The MIB module for managing an RSerPool implementation.
Copyright (c) 2009 IETF Trust and the persons identified as
authors of the code. All rights reserved.
Redistribution and use in source and binary forms, with or
without modification, are permitted provided that the
following conditions are met:
- Redistributions of source code must retain the above
copyright notice, this list of conditions and the
following disclaimer.
- Redistributions in binary form must reproduce the above
copyright notice, this list of conditions and the
following disclaimer in the documentation and/or other
materials provided with the distribution.
- Neither the name of Internet Society, IETF or IETF Trust,
nor the names of specific contributors, may be used to
endorse or promote products derived from this software
without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND
CONTRIBUTORS 'AS IS' AND ANY EXPRESS OR IMPLIED WARRANTIES,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
DAMAGE.
Dreibholz & Mulik Experimental [Page 12]
RFC 5525 RSerPool MIB Module April 2009
This version of this MIB module is part of RFC 5525;
see the RFC itself for full legal notices."
REVISION
"200904070000Z" -- April 07, 2009
DESCRIPTION
"This version of the MIB module is published as RFC 5525"
::= { experimental 125 }
-- ## RSerPool type definitions ###################################
RSerPoolENRPServerIdentifierTC ::= TEXTUAL-CONVENTION
DISPLAY-HINT "x"
STATUS current
DESCRIPTION "The ID of an ENRP server"
SYNTAX Unsigned32 (1..4294967295)
RSerPoolOperationScopeTC ::= TEXTUAL-CONVENTION
DISPLAY-HINT "1024t"
STATUS current
DESCRIPTION "The ID of an operation scope"
SYNTAX OCTET STRING (SIZE (0..65535))
RSerPoolPoolHandleTC ::= TEXTUAL-CONVENTION
DISPLAY-HINT "1024t"
STATUS current
DESCRIPTION "The pool handle"
SYNTAX OCTET STRING (SIZE (0..65535))
RserpoolPoolElementIdentifierTC ::= TEXTUAL-CONVENTION
DISPLAY-HINT "x"
STATUS current
DESCRIPTION "The pool element ID"
SYNTAX Unsigned32 (1..4294967295)
RSerPoolPolicyIdentifierTC ::= TEXTUAL-CONVENTION
DISPLAY-HINT "x"
STATUS current
DESCRIPTION "The ID of the pool policy"
SYNTAX Unsigned32 (1..4294967295)
RSerPoolPolicyLoadTC ::= TEXTUAL-CONVENTION
DISPLAY-HINT "d"
STATUS current
DESCRIPTION "The load status of a pool element"
SYNTAX Unsigned32 (0..4294967295)
Dreibholz & Mulik Experimental [Page 13]
RFC 5525 RSerPool MIB Module April 2009
RSerPoolPolicyWeightTC ::= TEXTUAL-CONVENTION
DISPLAY-HINT "d"
STATUS current
DESCRIPTION "The weight of a pool element"
SYNTAX Unsigned32 (0..4294967295)
RSerPoolTransportUseTypeTC ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION "The transport use of a pool element"
SYNTAX INTEGER {
dataOnly(0),
dataPlusControl(1)
}
RSerPoolOpaqueAddressTC ::= TEXTUAL-CONVENTION
DISPLAY-HINT "1024t"
STATUS current
DESCRIPTION "Opaque address"
SYNTAX OCTET STRING (SIZE (0..65535))
-- ## Top-level definitions #######################################
rserpoolMIBObjects OBJECT IDENTIFIER ::= { rserpoolMIB 1 }
rserpoolMIBConformance OBJECT IDENTIFIER ::= { rserpoolMIB 2 }
rserpoolENRPServers OBJECT IDENTIFIER ::= { rserpoolMIBObjects 1 }
rserpoolPoolElements OBJECT IDENTIFIER ::= { rserpoolMIBObjects 2 }
rserpoolPoolUsers OBJECT IDENTIFIER ::= { rserpoolMIBObjects 3 }
-- ################################################################
-- #### ENRP Servers Section ####
-- ################################################################
-- ## Definition of the ENRP server table #########################
rserpoolENRPTable OBJECT-TYPE
SYNTAX SEQUENCE OF RserpoolENRPEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table listing of ENRP servers."
::= { rserpoolENRPServers 1 }
rserpoolENRPEntry OBJECT-TYPE
SYNTAX RserpoolENRPEntry
MAX-ACCESS not-accessible
STATUS current
Dreibholz & Mulik Experimental [Page 14]
RFC 5525 RSerPool MIB Module April 2009
DESCRIPTION
"An ENRP server entry in the table listing of ENRP
servers."
INDEX { rserpoolENRPIndex }
::= { rserpoolENRPTable 1 }
RserpoolENRPEntry ::= SEQUENCE {
rserpoolENRPIndex Unsigned32,
rserpoolENRPOperationScope RSerPoolOperationScopeTC,
rserpoolENRPIdentifier RSerPoolENRPServerIdentifierTC,
rserpoolENRPDescription OCTET STRING,
rserpoolENRPUptime TimeTicks,
rserpoolENRPPort InetPortNumber,
rserpoolENRPASAPAnnouncePort InetPortNumber,
rserpoolENRPASAPAnnounceAddrType InetAddressType,
rserpoolENRPASAPAnnounceAddr InetAddress,
rserpoolENRPENRPAnnouncePort InetPortNumber,
rserpoolENRPENRPAnnounceAddrType InetAddressType,
rserpoolENRPENRPAnnounceAddr InetAddress }
rserpoolENRPIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An integer to uniquely identify an ENRP server."
::= { rserpoolENRPEntry 1 }
rserpoolENRPOperationScope OBJECT-TYPE
SYNTAX RSerPoolOperationScopeTC
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The definition of the operation scope of this ENRP server."
REFERENCE
"Section 1.2 of RFC 3237 defines the term operation scope."
::= { rserpoolENRPEntry 2 }
rserpoolENRPIdentifier OBJECT-TYPE
SYNTAX RSerPoolENRPServerIdentifierTC
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ENRP server identifier of this ENRP server."
REFERENCE
"Section 3.1 of RFC 5351 explains the ENRP server identifier."
::= { rserpoolENRPEntry 3 }
Dreibholz & Mulik Experimental [Page 15]
RFC 5525 RSerPool MIB Module April 2009
rserpoolENRPDescription OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0..255))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"A textual description of this ENRP server, e.g., its location
and a contact address of its administrator.
This object SHOULD be maintained in a persistent manner."
::= { rserpoolENRPEntry 4 }
rserpoolENRPUptime OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ENRP service uptime of this ENRP server."
::= { rserpoolENRPEntry 5 }
rserpoolENRPPort OBJECT-TYPE
SYNTAX InetPortNumber
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Stream Control Transmission Protocol (SCTP) port number of
the ENRP protocol endpoint of this ENRP server."
REFERENCE
"RFC 5353 defines the ENRP protocol."
::= { rserpoolENRPEntry 6 }
rserpoolENRPASAPAnnouncePort OBJECT-TYPE
SYNTAX InetPortNumber
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The destination UDP port number to which ASAP multicast announce
messages are sent."
REFERENCE
"Section 3.2 of RFC 5351 explains the server-discovery mechanism
using ASAP announces."
::= { rserpoolENRPEntry 7 }
rserpoolENRPASAPAnnounceAddrType OBJECT-TYPE
SYNTAX InetAddressType { ipv4(1), ipv6(2) }
MAX-ACCESS read-only
STATUS current
Dreibholz & Mulik Experimental [Page 16]
RFC 5525 RSerPool MIB Module April 2009
DESCRIPTION
"The network-layer protocol over which ASAP multicast announce
messages are sent."
REFERENCE
"Section 3.2 of RFC 5351 explains the server-discovery mechanism
using ASAP announces."
::= { rserpoolENRPEntry 8 }
rserpoolENRPASAPAnnounceAddr OBJECT-TYPE
SYNTAX InetAddress (SIZE(4|16))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The destination IP multicast address to which ASAP multicast
announce messages are sent. The type of this address is
given in rserpoolENRPASAPAnnounceAddrType."
REFERENCE
"Section 3.2 of RFC 5351 explains the server-discovery mechanism
using ASAP announces."
::= { rserpoolENRPEntry 9 }
rserpoolENRPENRPAnnouncePort OBJECT-TYPE
SYNTAX InetPortNumber
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The destination UDP port number to which ENRP multicast announce
messages are sent."
REFERENCE
"Section 3.1 of RFC 5353 explains the ENRP multicast
announce mechanism."
::= { rserpoolENRPEntry 10 }
rserpoolENRPENRPAnnounceAddrType OBJECT-TYPE
SYNTAX InetAddressType { ipv4(1), ipv6(2) }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The network-layer protocol over which ENRP multicast announce
messages are sent."
REFERENCE
"Section 3.1 of RFC 5353 explains the ENRP multicast
announce mechanism."
::= { rserpoolENRPEntry 11 }
rserpoolENRPENRPAnnounceAddr OBJECT-TYPE
SYNTAX InetAddress (SIZE(4|16))
MAX-ACCESS read-only
Dreibholz & Mulik Experimental [Page 17]
RFC 5525 RSerPool MIB Module April 2009
STATUS current
DESCRIPTION
"The destination multicast IP address to which ENRP multicast
announce messages are sent. The type of this address
is given in rserpoolENRPENRPAnnounceAddrType."
REFERENCE
"Section 3.1 of RFC 5353 explains the ENRP multicast
announce mechanism."
::= { rserpoolENRPEntry 12 }
-- ## Definition of the pool table ################################
rserpoolENRPPoolTable OBJECT-TYPE
SYNTAX SEQUENCE OF RserpoolENRPPoolEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table listing of pools."
::= { rserpoolENRPServers 3 }
rserpoolENRPPoolEntry OBJECT-TYPE
SYNTAX RserpoolENRPPoolEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The pool entry in the table listing of pools."
INDEX { rserpoolENRPIndex, rserpoolENRPPoolIndex }
::= { rserpoolENRPPoolTable 1 }
RserpoolENRPPoolEntry ::= SEQUENCE {
rserpoolENRPPoolIndex Unsigned32,
rserpoolENRPPoolHandle RSerPoolPoolHandleTC }
rserpoolENRPPoolIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An integer to uniquely identify a pool."
::= { rserpoolENRPPoolEntry 1 }
rserpoolENRPPoolHandle OBJECT-TYPE
SYNTAX RSerPoolPoolHandleTC
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The pool handle of this pool."
REFERENCE
"Section 1.2 of RFC 3237 defines the term pool handle."
Dreibholz & Mulik Experimental [Page 18]
RFC 5525 RSerPool MIB Module April 2009
::= { rserpoolENRPPoolEntry 2 }
-- ## Definition of the pool element table ########################
rserpoolENRPPoolElementTable OBJECT-TYPE
SYNTAX SEQUENCE OF RserpoolENRPPoolElementEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table listing of pool elements."
::= { rserpoolENRPServers 4 }
rserpoolENRPPoolElementEntry OBJECT-TYPE
SYNTAX RserpoolENRPPoolElementEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A pool element in the table listing of pool elements."
INDEX {
rserpoolENRPIndex,
rserpoolENRPPoolIndex,
rserpoolENRPPoolElementIndex }
::= { rserpoolENRPPoolElementTable 1 }
RserpoolENRPPoolElementEntry ::= SEQUENCE {
rserpoolENRPPoolElementIndex Unsigned32,
rserpoolENRPPoolElementID RserpoolPoolElementIdentifierTC,
rserpoolENRPASAPTransportPort InetPortNumber,
rserpoolENRPUserTransportProto Unsigned32,
rserpoolENRPUserTransportPort InetPortNumber,
rserpoolENRPUserTransportUse RSerPoolTransportUseTypeTC,
rserpoolENRPPolicyID RSerPoolPolicyIdentifierTC,
rserpoolENRPPolicyDescription OCTET STRING,
rserpoolENRPPolicyWeight RSerPoolPolicyWeightTC,
rserpoolENRPPolicyLoad RSerPoolPolicyLoadTC,
rserpoolENRPPolicyLoadDeg RSerPoolPolicyLoadTC,
rserpoolENRPRegistrationLife TimeTicks,
rserpoolENRPHomeENRPServer RSerPoolENRPServerIdentifierTC }
rserpoolENRPPoolElementIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
Dreibholz & Mulik Experimental [Page 19]
RFC 5525 RSerPool MIB Module April 2009
DESCRIPTION
"An integer to uniquely identify a pool element. Note,
that uniqueness of a pool element identifier in the pool
is not enforced; therefore, this index is required here!"
::={ rserpoolENRPPoolElementEntry 1 }
rserpoolENRPPoolElementID OBJECT-TYPE
SYNTAX RserpoolPoolElementIdentifierTC
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The pool element identifier of this pool element."
REFERENCE
"Section 2.2 of RFC 5351 explains the pool element identifier
usage."
::={ rserpoolENRPPoolElementEntry 2 }
rserpoolENRPASAPTransportPort OBJECT-TYPE
SYNTAX InetPortNumber
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The SCTP port number of the ASAP endpoint of this pool
element."
REFERENCE
"Section 3.10 of RFC 5354 defines the ASAP Transport Parameter of
which the port number is given here."
::= { rserpoolENRPPoolElementEntry 3 }
rserpoolENRPUserTransportProto OBJECT-TYPE
SYNTAX Unsigned32 (0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The transport protocol number of the service endpoint
of this pool element."
REFERENCE
"Section 3.10 of RFC 5354 defines the User Transport Parameter of
which the transport protocol number is given here."
::= { rserpoolENRPPoolElementEntry 4 }
rserpoolENRPUserTransportPort OBJECT-TYPE
SYNTAX InetPortNumber
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The transport protocol's port number of the service
endpoint of this pool element."
Dreibholz & Mulik Experimental [Page 20]
RFC 5525 RSerPool MIB Module April 2009
REFERENCE
"Section 3.10 of RFC 5354 defines the User Transport Parameter of
which the port number is given here."
::= { rserpoolENRPPoolElementEntry 5 }
rserpoolENRPUserTransportUse OBJECT-TYPE
SYNTAX RSerPoolTransportUseTypeTC
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The transport use of the service endpoint of this pool
element."
REFERENCE
"Section 3.10 of RFC 5354 defines the User Transport Parameter of
which the transport use is given here."
::= { rserpoolENRPPoolElementEntry 6 }
rserpoolENRPPolicyID OBJECT-TYPE
SYNTAX RSerPoolPolicyIdentifierTC
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The pool policy of this pool element."
REFERENCE
"Section 3.8 of RFC 5354 defines the Member Selection Policy
Parameter of which the policy identifier is given here."
::= { rserpoolENRPPoolElementEntry 7 }
rserpoolENRPPolicyDescription OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0..255))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The textual description of the pool policy of this pool
element."
::= { rserpoolENRPPoolElementEntry 8 }
rserpoolENRPPolicyWeight OBJECT-TYPE
SYNTAX RSerPoolPolicyWeightTC
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The pool policy's weight parameter for this pool element."
REFERENCE
"Section 3.8 of RFC 5354 defines the Member Selection Policy
Parameter of which the policy's weight parameter is given here."
::= { rserpoolENRPPoolElementEntry 9 }
Dreibholz & Mulik Experimental [Page 21]
RFC 5525 RSerPool MIB Module April 2009
rserpoolENRPPolicyLoad OBJECT-TYPE
SYNTAX RSerPoolPolicyLoadTC
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The pool policy's load status for this pool element."
REFERENCE
"Section 3.8 of RFC 5354 defines the Member Selection Policy
Parameter of which the policy's load parameter is given here."
::= { rserpoolENRPPoolElementEntry 10 }
rserpoolENRPPolicyLoadDeg OBJECT-TYPE
SYNTAX RSerPoolPolicyLoadTC
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The pool policy's load degradation parameter for this pool
element."
REFERENCE
"Section 3.8 of RFC 5354 defines the Member Selection Policy
Parameter of which the policy's load degradation parameter is
given here."
::= { rserpoolENRPPoolElementEntry 11 }
rserpoolENRPRegistrationLife OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The registration life of this pool element."
REFERENCE
"Section 3.10 of RFC 5354 defines the Registration Life."
::= { rserpoolENRPPoolElementEntry 12 }
rserpoolENRPHomeENRPServer OBJECT-TYPE
SYNTAX RSerPoolENRPServerIdentifierTC
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ID of the Home ENRP server of this pool element."
REFERENCE
"Section 3.10 of RFC 5354 defines the Home ENRP Server
Identifier."
::= { rserpoolENRPPoolElementEntry 13 }
-- ## Definition of the ASAP transport address list table #########
rserpoolENRPASAPAddrTable OBJECT-TYPE
SYNTAX SEQUENCE OF RserpoolENRPASAPAddrTableEntry
Dreibholz & Mulik Experimental [Page 22]
RFC 5525 RSerPool MIB Module April 2009
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table listing of all IP addresses of the ASAP transport
endpoint."
REFERENCE
"Section 3.10 of RFC 5354 defines the ASAP Transport Parameter of
which the addresses are listed in this table."
::= { rserpoolENRPServers 5 }
rserpoolENRPASAPAddrTableEntry OBJECT-TYPE
SYNTAX RserpoolENRPASAPAddrTableEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An IP address of the ASAP transport endpoint."
REFERENCE
"Section 3.10 of RFC 5354 defines the ASAP Transport Parameter of
which an address is contained by this entry."
INDEX {
rserpoolENRPIndex,
rserpoolENRPPoolIndex,
rserpoolENRPPoolElementIndex,
rserpoolENRPASAPAddrTableIndex }
::= { rserpoolENRPASAPAddrTable 1 }
RserpoolENRPASAPAddrTableEntry ::= SEQUENCE {
rserpoolENRPASAPAddrTableIndex Unsigned32,
rserpoolENRPASAPL3Type InetAddressType,
rserpoolENRPASAPL3Addr InetAddress }
rserpoolENRPASAPAddrTableIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A unique identifier for the IP address of an ASAP transport
endpoint."
::= { rserpoolENRPASAPAddrTableEntry 1 }
rserpoolENRPASAPL3Type OBJECT-TYPE
SYNTAX InetAddressType { ipv4(1), ipv6(2) }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The network-layer protocol (IPv4 or IPv6) of an IP address of
an ASAP transport endpoint."
REFERENCE
Dreibholz & Mulik Experimental [Page 23]
RFC 5525 RSerPool MIB Module April 2009
"Section 3.10 of RFC 5354 defines the ASAP Transport Parameter of
which the network-layer protocol number is given here."
::= { rserpoolENRPASAPAddrTableEntry 2 }
rserpoolENRPASAPL3Addr OBJECT-TYPE
SYNTAX InetAddress (SIZE(4|16))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The IP address of an ASAP transport endpoint. The type of
this address is given in rserpoolENRPASAPL3Type."
REFERENCE
"Section 3.10 of RFC 5354 defines the ASAP Transport Parameter of
which the network-layer address (IPv4 or IPv6) is given here."
::= { rserpoolENRPASAPAddrTableEntry 3 }
-- ## Definition of the user transport address list table #########
rserpoolENRPUserAddrTable OBJECT-TYPE
SYNTAX SEQUENCE OF RserpoolENRPUserAddrTableEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table listing of all IP addresses of the user
transport endpoint."
REFERENCE
"Section 3.10 of RFC 5354 defines the User Transport Parameter of
which the addresses are listed in this table."
::= { rserpoolENRPServers 6 }
rserpoolENRPUserAddrTableEntry OBJECT-TYPE
SYNTAX RserpoolENRPUserAddrTableEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An IP address of the user transport endpoint."
REFERENCE
"Section 3.10 of RFC 5354 defines the User Transport Parameter of
which an address is contained by this entry."
INDEX {
rserpoolENRPIndex,
rserpoolENRPPoolIndex,
rserpoolENRPPoolElementIndex,
rserpoolENRPUserAddrTableIndex }
::= { rserpoolENRPUserAddrTable 1 }
RserpoolENRPUserAddrTableEntry ::= SEQUENCE {
rserpoolENRPUserAddrTableIndex Unsigned32,
rserpoolENRPUserL3Type InetAddressType,
Dreibholz & Mulik Experimental [Page 24]
RFC 5525 RSerPool MIB Module April 2009
rserpoolENRPUserL3Addr InetAddress,
rserpoolENRPUserL3Opaque RSerPoolOpaqueAddressTC }
rserpoolENRPUserAddrTableIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A unique identifier for the IP address of a user transport
endpoint."
::= { rserpoolENRPUserAddrTableEntry 1 }
rserpoolENRPUserL3Type OBJECT-TYPE
SYNTAX InetAddressType { unknown(0), ipv4(1), ipv6(2) }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The network-layer protocol (IPv4 or IPv6) of an IP address
of a user transport endpoint. Set to unknown for an opaque
address."
REFERENCE
"Section 3.10 of RFC 5354 defines the User Transport Parameter of
which the network-layer protocol number is given here."
::= { rserpoolENRPUserAddrTableEntry 2 }
rserpoolENRPUserL3Addr OBJECT-TYPE
SYNTAX InetAddress (SIZE(0|4|16))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The IP address of a user transport endpoint. The type of
this address is given in rserpoolENRPUserL3Type."
REFERENCE
"Section 3.10 of RFC 5354 defines the User Transport Parameter of
which the network-layer address (IPv4 or IPv6) is given here."
::= { rserpoolENRPUserAddrTableEntry 3 }
rserpoolENRPUserL3Opaque OBJECT-TYPE
SYNTAX RSerPoolOpaqueAddressTC
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The opaque address of a user transport endpoint."
REFERENCE
"Section 3.16 of RFC 5354 defines the opaque transport address."
::= { rserpoolENRPUserAddrTableEntry 4 }
Dreibholz & Mulik Experimental [Page 25]
RFC 5525 RSerPool MIB Module April 2009
-- ## Definition of ENRP address list table #######################
rserpoolENRPENRPAddrTable OBJECT-TYPE
SYNTAX SEQUENCE OF RserpoolENRPENRPAddrTableEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table listing of all IP addresses of the ENRP
transport endpoint."
::= { rserpoolENRPServers 7 }
rserpoolENRPENRPAddrTableEntry OBJECT-TYPE
SYNTAX RserpoolENRPENRPAddrTableEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An IP address of the ENRP transport endpoint."
INDEX {
rserpoolENRPIndex,
rserpoolENRPENRPAddrTableIndex }
::= { rserpoolENRPENRPAddrTable 1 }
RserpoolENRPENRPAddrTableEntry ::= SEQUENCE {
rserpoolENRPENRPAddrTableIndex Unsigned32,
rserpoolENRPENRPL3Type InetAddressType,
rserpoolENRPENRPL3Addr InetAddress }
rserpoolENRPENRPAddrTableIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A unique identifier for the IP address of an ENRP transport
endpoint."
::= { rserpoolENRPENRPAddrTableEntry 1 }
rserpoolENRPENRPL3Type OBJECT-TYPE
SYNTAX InetAddressType { ipv4(1), ipv6(2) }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The network-layer protocol (IPv4 or IPv6) of an IP address of
an ENRP transport endpoint."
REFERENCE
"RFC 5353 defines the ENRP protocol."
::= { rserpoolENRPENRPAddrTableEntry 2 }
Dreibholz & Mulik Experimental [Page 26]
RFC 5525 RSerPool MIB Module April 2009
rserpoolENRPENRPL3Addr OBJECT-TYPE
SYNTAX InetAddress (SIZE(4|16))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The IP address of an ENRP transport endpoint. The type of
this address is given in rserpoolENRPENRPL3Type."
REFERENCE
"RFC 5353 defines the ENRP protocol."
::= { rserpoolENRPENRPAddrTableEntry 3 }
-- ## Definition of peer table ####################################
rserpoolENRPPeerTable OBJECT-TYPE
SYNTAX SEQUENCE OF RserpoolENRPPeerEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table listing of a peer table."
::= { rserpoolENRPServers 8 }
rserpoolENRPPeerEntry OBJECT-TYPE
SYNTAX RserpoolENRPPeerEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A peer entry in the table listing of a peer table."
INDEX { rserpoolENRPPeerIndex }
::= { rserpoolENRPPeerTable 1 }
RserpoolENRPPeerEntry ::= SEQUENCE {
rserpoolENRPPeerIndex Unsigned32,
rserpoolENRPPeerIdentifier RSerPoolENRPServerIdentifierTC,
rserpoolENRPPeerPort InetPortNumber,
rserpoolENRPPeerLastHeard TimeTicks }
rserpoolENRPPeerIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A unique identifier for a peer entry in the table
listing of a peer table."
::= { rserpoolENRPPeerEntry 1 }
rserpoolENRPPeerIdentifier OBJECT-TYPE
SYNTAX RSerPoolENRPServerIdentifierTC
MAX-ACCESS read-only
STATUS current
Dreibholz & Mulik Experimental [Page 27]
RFC 5525 RSerPool MIB Module April 2009
DESCRIPTION
"The ENRP identifier of this peer."
REFERENCE
"RFC 5353 explains the usage of the ENRP server identifier."
::= { rserpoolENRPPeerEntry 2 }
rserpoolENRPPeerPort OBJECT-TYPE
SYNTAX InetPortNumber
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The SCTP port number of the ENRP transport endpoint of
this peer."
REFERENCE
"RFC 5353 defines the ENRP protocol."
::= { rserpoolENRPPeerEntry 3 }
rserpoolENRPPeerLastHeard OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time since the reception of the last ENRP Presence
message of this peer."
REFERENCE
"Section 4.1 of RFC 5353 defines the last heard value."
::= { rserpoolENRPPeerEntry 4 }
-- ## Definition of peer address list table #######################
rserpoolENRPPeerAddrTable OBJECT-TYPE
SYNTAX SEQUENCE OF RserpoolENRPPeerAddrTableEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table listing of the peer endpoint addresses."
::= { rserpoolENRPServers 9 }
rserpoolENRPPeerAddrTableEntry OBJECT-TYPE
SYNTAX RserpoolENRPPeerAddrTableEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table listing of all IP addresses of the ENRP
transport endpoint of a peer referenced by rserpoolENRPPeerIndex."
INDEX {
rserpoolENRPPeerIndex,
rserpoolENRPPeerAddrTableIndex }
::= { rserpoolENRPPeerAddrTable 1 }
Dreibholz & Mulik Experimental [Page 28]
RFC 5525 RSerPool MIB Module April 2009
RserpoolENRPPeerAddrTableEntry ::= SEQUENCE {
rserpoolENRPPeerAddrTableIndex Unsigned32,
rserpoolENRPPeerL3Type InetAddressType,
rserpoolENRPPeerL3Addr InetAddress }
rserpoolENRPPeerAddrTableIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A unique identifier for the IP address of a peer ENRP
transport endpoint."
::= { rserpoolENRPPeerAddrTableEntry 1 }
rserpoolENRPPeerL3Type OBJECT-TYPE
SYNTAX InetAddressType { ipv4(1), ipv6(2) }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The network-layer protocol (IPv4 or IPv6) of an IP address
of a peer ENRP transport endpoint."
REFERENCE
"RFC 5353 defines the ENRP protocol."
::= { rserpoolENRPPeerAddrTableEntry 2 }
rserpoolENRPPeerL3Addr OBJECT-TYPE
SYNTAX InetAddress (SIZE(4|16))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The IP address of a peer ENRP transport endpoint. The type
of this address is given in rserpoolENRPPeerL3Type."
REFERENCE
"RFC 5353 defines the ENRP protocol."
::= { rserpoolENRPPeerAddrTableEntry 3 }
-- ################################################################
-- #### Pool Elements Section ####
-- ################################################################
-- ## Definition of the pool element table ########################
rserpoolPETable OBJECT-TYPE
SYNTAX SEQUENCE OF RserpoolPEEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table listing of pool elements."
::= { rserpoolPoolElements 1 }
Dreibholz & Mulik Experimental [Page 29]
RFC 5525 RSerPool MIB Module April 2009
rserpoolPEEntry OBJECT-TYPE
SYNTAX RserpoolPEEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A pool element in the table listing of pool elements."
INDEX { rserpoolPEIndex }
::= { rserpoolPETable 1 }
RserpoolPEEntry ::= SEQUENCE {
rserpoolPEIndex Unsigned32,
rserpoolPEOperationScope RSerPoolOperationScopeTC,
rserpoolPEPoolHandle RSerPoolPoolHandleTC,
rserpoolPEIdentifier RserpoolPoolElementIdentifierTC,
rserpoolPEDescription OCTET STRING,
rserpoolPEUptime TimeTicks,
rserpoolPEASAPTransportPort InetPortNumber,
rserpoolPEUserTransportProto Unsigned32,
rserpoolPEUserTransportPort InetPortNumber,
rserpoolPEUserTransportUse RSerPoolTransportUseTypeTC,
rserpoolPEPolicyID RSerPoolPolicyIdentifierTC,
rserpoolPEPolicyDescription OCTET STRING,
rserpoolPEPolicyWeight RSerPoolPolicyWeightTC,
rserpoolPEPolicyLoad RSerPoolPolicyLoadTC,
rserpoolPEPolicyLoadDeg RSerPoolPolicyLoadTC,
rserpoolPERegistrationLife TimeTicks,
rserpoolPEHomeENRPServer RSerPoolENRPServerIdentifierTC }
rserpoolPEIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An integer to uniquely identify a pool element. Note,
that uniqueness of a pool element identifier in the pool
is not enforced; therefore, this index is required here!"
::={ rserpoolPEEntry 1 }
rserpoolPEOperationScope OBJECT-TYPE
SYNTAX RSerPoolOperationScopeTC
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The operation scope of this pool element."
REFERENCE
"Section 1.2 of RFC 3237 defines the term operation scope."
::= { rserpoolPEEntry 2 }
Dreibholz & Mulik Experimental [Page 30]
RFC 5525 RSerPool MIB Module April 2009
rserpoolPEPoolHandle OBJECT-TYPE
SYNTAX RSerPoolPoolHandleTC
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The pool handle of this pool element. Changing this object
will update the pool element's pool handle and result in a
re-registration.
This object SHOULD be maintained in a persistent manner."
REFERENCE
"Section 1.2 of RFC 3237 defines the term pool handle."
::={ rserpoolPEEntry 3 }
rserpoolPEIdentifier OBJECT-TYPE
SYNTAX RserpoolPoolElementIdentifierTC
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The pool element identifier of this pool element."
REFERENCE
"Section 3.10 of RFC 5354 defines the pool element identifier."
::={ rserpoolPEEntry 4 }
rserpoolPEDescription OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0..255))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"A textual description of this pool element, e.g., its location
and a contact address of its administrator.
This object SHOULD be maintained in a persistent manner."
::= { rserpoolPEEntry 5 }
rserpoolPEUptime OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ENRP service uptime of this pool element."
::= { rserpoolPEEntry 6 }
rserpoolPEASAPTransportPort OBJECT-TYPE
SYNTAX InetPortNumber
MAX-ACCESS read-only
STATUS current
DESCRIPTION
Dreibholz & Mulik Experimental [Page 31]
RFC 5525 RSerPool MIB Module April 2009
"The SCTP port number of the ASAP endpoint of this pool element."
REFERENCE
"Section 3.10 of RFC 5354 defines the ASAP Transport Parameter of
which the port number is given here."
::= { rserpoolPEEntry 7 }
rserpoolPEUserTransportProto OBJECT-TYPE
SYNTAX Unsigned32 (0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The transport protocol number of the service endpoint
of this pool element."
REFERENCE
"Section 3.10 of RFC 5354 defines the User Transport Parameter of
which the transport protocol number is given here."
::= { rserpoolPEEntry 8 }
rserpoolPEUserTransportPort OBJECT-TYPE
SYNTAX InetPortNumber
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The transport protocol's port number of the service
endpoint of this pool element."
REFERENCE
"Section 3.10 of RFC 5354 defines the User Transport Parameter of
which the port number is given here."
::= { rserpoolPEEntry 9 }
rserpoolPEUserTransportUse OBJECT-TYPE
SYNTAX RSerPoolTransportUseTypeTC
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The transport use of the service endpoint of this pool element."
REFERENCE
"Section 3.10 of RFC 5354 defines the User Transport Parameter of
which the transport use is given here."
::= { rserpoolPEEntry 10 }
rserpoolPEPolicyID OBJECT-TYPE
SYNTAX RSerPoolPolicyIdentifierTC
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The pool policy of this pool element. Changing this object
will update the pool element's policy and result in a
Dreibholz & Mulik Experimental [Page 32]
RFC 5525 RSerPool MIB Module April 2009
re-registration.
This object SHOULD be maintained in a persistent manner."
REFERENCE
"Section 3.8 of RFC 5354 defines the Member Selection Policy
Parameter of which the policy identifier is given here."
::= { rserpoolPEEntry 11 }
rserpoolPEPolicyDescription OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0..255))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The textual description of the pool policy of this pool element.
This object SHOULD be maintained in a persistent manner."
::= { rserpoolPEEntry 12 }
rserpoolPEPolicyWeight OBJECT-TYPE
SYNTAX RSerPoolPolicyWeightTC
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The pool policy's weight parameter for this pool element.
Changing this object will update the pool element's policy
weight setting and result in a re-registration.
This object SHOULD be maintained in a persistent manner."
REFERENCE
"Section 3.8 of RFC 5354 defines the Member Selection Policy
Parameter of which the policy's weight parameter is given here."
::= { rserpoolPEEntry 13 }
rserpoolPEPolicyLoad OBJECT-TYPE
SYNTAX RSerPoolPolicyLoadTC
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The pool policy's load status for this pool element."
REFERENCE
"Section 3.8 of RFC 5354 defines the Member Selection Policy
Parameter of which the policy's load parameter is given here."
::= { rserpoolPEEntry 14 }
Dreibholz & Mulik Experimental [Page 33]
RFC 5525 RSerPool MIB Module April 2009
rserpoolPEPolicyLoadDeg OBJECT-TYPE
SYNTAX RSerPoolPolicyLoadTC
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The pool policy's load degradation parameter for this pool
element. Changing this object will update the pool element's
load degradation setting and result in a re-registration.
This object SHOULD be maintained in a persistent manner."
REFERENCE
"Section 3.8 of RFC 5354 defines the Member Selection Policy
Parameter of which the policy's load degradation parameter is
given here."
::= { rserpoolPEEntry 15 }
rserpoolPERegistrationLife OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The registration life of this pool element. Changing this
object will update the pool element's lifetime setting and
result in a re-registration.
This object SHOULD be maintained in a persistent manner."
REFERENCE
"Section 3.10 of RFC 5354 defines the Registration Life."
::= { rserpoolPEEntry 16 }
rserpoolPEHomeENRPServer OBJECT-TYPE
SYNTAX RSerPoolENRPServerIdentifierTC
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ID of the Home ENRP server of this pool element."
REFERENCE
"Section 3.10 of RFC 5354 defines the Home ENRP Server
Identifier."
::= { rserpoolPEEntry 17 }
-- ## Definition of the ASAP transport address list table #########
rserpoolPEASAPAddrTable OBJECT-TYPE
SYNTAX SEQUENCE OF RserpoolPEASAPAddrTableEntry
MAX-ACCESS not-accessible
STATUS current
Dreibholz & Mulik Experimental [Page 34]
RFC 5525 RSerPool MIB Module April 2009
DESCRIPTION
"A table listing of all IP addresses of the ASAP transport
endpoint."
REFERENCE
"Section 3.10 of RFC 5354 defines the ASAP Transport Parameter of
which the addresses are listed in this table."
::= { rserpoolPoolElements 2 }
rserpoolPEASAPAddrTableEntry OBJECT-TYPE
SYNTAX RserpoolPEASAPAddrTableEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An IP address of the ASAP transport endpoint."
REFERENCE
"Section 3.10 of RFC 5354 defines the ASAP Transport Parameter of
which an address is contained by this entry."
INDEX {
rserpoolPEIndex,
rserpoolPEASAPAddrTableIndex }
::= { rserpoolPEASAPAddrTable 1 }
RserpoolPEASAPAddrTableEntry ::= SEQUENCE {
rserpoolPEASAPAddrTableIndex Unsigned32,
rserpoolPEASAPL3Type InetAddressType,
rserpoolPEASAPL3Addr InetAddress }
rserpoolPEASAPAddrTableIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A unique identifier for the IP address of an ASAP transport
endpoint."
::= { rserpoolPEASAPAddrTableEntry 1 }
rserpoolPEASAPL3Type OBJECT-TYPE
SYNTAX InetAddressType { ipv4(1), ipv6(2) }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The network-layer protocol (IPv4 or IPv6) of an IP address of
an ASAP transport endpoint."
REFERENCE
"Section 3.10 of RFC 5354 defines the ASAP Transport Parameter of
which the network-layer protocol number is given here."
::= { rserpoolPEASAPAddrTableEntry 2 }
Dreibholz & Mulik Experimental [Page 35]
RFC 5525 RSerPool MIB Module April 2009
rserpoolPEASAPL3Addr OBJECT-TYPE
SYNTAX InetAddress (SIZE(4|16))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The IP address of an ASAP transport endpoint. The type of
this address is given in rserpoolPEASAPL3Type."
REFERENCE
"Section 3.10 of RFC 5354 defines the ASAP Transport Parameter of
which the network-layer address (IPv4 or IPv6) is given here."
::= { rserpoolPEASAPAddrTableEntry 3 }
-- ## Definition of the user transport address list table #########
rserpoolPEUserAddrTable OBJECT-TYPE
SYNTAX SEQUENCE OF RserpoolPEUserAddrTableEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table listing of all IP addresses of the user
transport endpoint."
REFERENCE
"Section 3.10 of RFC 5354 defines the User Transport Parameter of
which the addresses are listed in this table."
::= { rserpoolPoolElements 6 }
rserpoolPEUserAddrTableEntry OBJECT-TYPE
SYNTAX RserpoolPEUserAddrTableEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An IP address of the user transport endpoint."
REFERENCE
"Section 3.10 of RFC 5354 defines the User Transport Parameter of
which an address is contained by this entry."
INDEX {
rserpoolPEIndex,
rserpoolPEUserAddrTableIndex }
::= { rserpoolPEUserAddrTable 1 }
RserpoolPEUserAddrTableEntry ::= SEQUENCE {
rserpoolPEUserAddrTableIndex Unsigned32,
rserpoolPEUserL3Type InetAddressType,
rserpoolPEUserL3Addr InetAddress,
rserpoolPEUserL3Opaque RSerPoolOpaqueAddressTC }
rserpoolPEUserAddrTableIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
Dreibholz & Mulik Experimental [Page 36]
RFC 5525 RSerPool MIB Module April 2009
STATUS current
DESCRIPTION
"A unique identifier for the IP address of a user transport
endpoint."
::= { rserpoolPEUserAddrTableEntry 1 }
rserpoolPEUserL3Type OBJECT-TYPE
SYNTAX InetAddressType { unknown(0), ipv4(1), ipv6(2) }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The network-layer protocol of an IP address of a user transport
endpoint. Set to unknown for opaque address."
REFERENCE
"Section 3.10 of RFC 5354 defines the User Transport Parameter of
which the network-layer protocol number is given here."
::= { rserpoolPEUserAddrTableEntry 2 }
rserpoolPEUserL3Addr OBJECT-TYPE
SYNTAX InetAddress (SIZE(0|4|16))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The IP address of a user transport endpoint. The type of
this address is given in rserpoolPEUserL3Addr."
REFERENCE
"Section 3.10 of RFC 5354 defines the User Transport Parameter of
which the network-layer address (IPv4 or IPv6) is given here."
::= { rserpoolPEUserAddrTableEntry 3 }
rserpoolPEUserL3Opaque OBJECT-TYPE
SYNTAX RSerPoolOpaqueAddressTC
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The opaque address of a user transport endpoint."
REFERENCE
"Section 3.16 of RFC 5354 defines the opaque transport address."
::= { rserpoolPEUserAddrTableEntry 4 }
-- ################################################################
-- #### Pool Users Section ####
-- ################################################################
-- ## Definition of the pool user table ###########################
rserpoolPUTable OBJECT-TYPE
SYNTAX SEQUENCE OF RserpoolPUEntry
MAX-ACCESS not-accessible
Dreibholz & Mulik Experimental [Page 37]
RFC 5525 RSerPool MIB Module April 2009
STATUS current
DESCRIPTION
"The table listing of pool users."
::= { rserpoolPoolUsers 1 }
rserpoolPUEntry OBJECT-TYPE
SYNTAX RserpoolPUEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A pool user in the table listing of pool users."
INDEX { rserpoolPUIndex }
::= { rserpoolPUTable 1 }
RserpoolPUEntry ::= SEQUENCE {
rserpoolPUIndex Unsigned32,
rserpoolPUOperationScope RSerPoolOperationScopeTC,
rserpoolPUPoolHandle RSerPoolPoolHandleTC,
rserpoolPUDescription OCTET STRING,
rserpoolPUUptime TimeTicks }
rserpoolPUIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An integer to uniquely identify a pool user."
::= { rserpoolPUEntry 1 }
rserpoolPUOperationScope OBJECT-TYPE
SYNTAX RSerPoolOperationScopeTC
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The operation scope of this pool user."
REFERENCE
"Section 1.2 of RFC 3237 defines the term operation scope."
::= { rserpoolPUEntry 2 }
rserpoolPUPoolHandle OBJECT-TYPE
SYNTAX RSerPoolPoolHandleTC
MAX-ACCESS read-write
STATUS current
Dreibholz & Mulik Experimental [Page 38]
RFC 5525 RSerPool MIB Module April 2009
DESCRIPTION
"The pool handle of this pool user. Changing this object
will update the pool user's pool handle for all future
sessions.
This object SHOULD be maintained in a persistent manner."
REFERENCE
"Section 1.2 of RFC 3237 defines the term pool handle."
::={ rserpoolPUEntry 3 }
rserpoolPUDescription OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0..255))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"A textual description of this pool user, e.g., its location
and a contact address of its administrator.
This object SHOULD be maintained in a persistent manner."
::= { rserpoolPUEntry 4 }
rserpoolPUUptime OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ENRP service uptime of this pool user."
::= { rserpoolPUEntry 5 }
-- ## MIB conformance and compliance ##############################
rserpoolMIBCompliances OBJECT IDENTIFIER ::= {
rserpoolMIBConformance 1
}
rserpoolMIBGroups OBJECT IDENTIFIER ::= {
rserpoolMIBConformance 2
}
rserpoolMIBCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for SNMP entities that implement
RSerPool."
MODULE
MANDATORY-GROUPS {
rserpoolENRPGroup,
rserpoolPEGroup,
rserpoolPUGroup }
Dreibholz & Mulik Experimental [Page 39]
RFC 5525 RSerPool MIB Module April 2009
::= { rserpoolMIBCompliances 1 }
rserpoolENRPGroup OBJECT-GROUP
OBJECTS {
rserpoolENRPOperationScope,
rserpoolENRPIdentifier,
rserpoolENRPDescription,
rserpoolENRPUptime,
rserpoolENRPPort,
rserpoolENRPASAPAnnouncePort,
rserpoolENRPASAPAnnounceAddr,
rserpoolENRPASAPAnnounceAddrType,
rserpoolENRPENRPAnnounceAddrType,
rserpoolENRPENRPAnnouncePort,
rserpoolENRPENRPAnnounceAddr,
rserpoolENRPPoolHandle,
rserpoolENRPPoolElementID,
rserpoolENRPASAPTransportPort,
rserpoolENRPUserTransportProto,
rserpoolENRPUserTransportUse,
rserpoolENRPUserTransportPort,
rserpoolENRPPolicyID,
rserpoolENRPPolicyDescription,
rserpoolENRPPolicyWeight,
rserpoolENRPPolicyLoad,
rserpoolENRPPolicyLoadDeg,
rserpoolENRPRegistrationLife,
rserpoolENRPHomeENRPServer,
rserpoolENRPASAPL3Type,
rserpoolENRPASAPL3Addr,
rserpoolENRPUserL3Type,
rserpoolENRPUserL3Addr,
rserpoolENRPUserL3Opaque,
rserpoolENRPENRPL3Type,
rserpoolENRPENRPL3Addr,
rserpoolENRPPeerIdentifier,
rserpoolENRPPeerPort,
rserpoolENRPPeerLastHeard,
rserpoolENRPPeerL3Type,
rserpoolENRPPeerL3Addr }
STATUS current
DESCRIPTION
Dreibholz & Mulik Experimental [Page 40]
RFC 5525 RSerPool MIB Module April 2009
"The group contains all ENRP server instances
running on the system"
::= { rserpoolMIBGroups 1 }
rserpoolPEGroup OBJECT-GROUP
OBJECTS {
rserpoolPEOperationScope,
rserpoolPEPoolHandle,
rserpoolPEIdentifier,
rserpoolPEDescription,
rserpoolPEUptime,
rserpoolPEASAPTransportPort,
rserpoolPEUserTransportProto,
rserpoolPEUserTransportPort,
rserpoolPEUserTransportUse,
rserpoolPEPolicyID,
rserpoolPEPolicyDescription,
rserpoolPEPolicyWeight,
rserpoolPEPolicyLoad,
rserpoolPEPolicyLoadDeg,
rserpoolPERegistrationLife,
rserpoolPEHomeENRPServer,
rserpoolPEASAPL3Type,
rserpoolPEASAPL3Addr,
rserpoolPEUserL3Type,
rserpoolPEUserL3Addr,
rserpoolPEUserL3Opaque }
STATUS current
DESCRIPTION
"The group contains all pool element instances
running on the system"
::= { rserpoolMIBGroups 2 }
rserpoolPUGroup OBJECT-GROUP
OBJECTS { rserpoolPUOperationScope,
rserpoolPUPoolHandle,
rserpoolPUDescription,
rserpoolPUUptime }
STATUS current
DESCRIPTION
"The group contains all pool user instances
running on the system"
::= { rserpoolMIBGroups 3 }
END
Dreibholz & Mulik Experimental [Page 41]
RFC 5525 RSerPool MIB Module April 2009
7. Operational Considerations
The RSerPool MIB is an Experimental track MIB module, since the
RSerPool documents are Experimental RFCs.
8. Security Considerations
There are a number of management objects defined in this MIB module
with a MAX-ACCESS clause of read-write and/or read-create. Such
objects may be considered sensitive or vulnerable in some network
environments. The support for SET operations in a non-secure
environment without proper protection can have a negative effect on
network operations. These are the tables and objects and their
sensitivity/vulnerability:
rserpoolENRPDescription (textual description change)
rserpoolPEPoolHandle (pool handle of pool element change, similar
to ASAP)
rserpoolPEDescription (textual description change)
rserpoolPEPolicyID (pool element ID change, similar to ASAP)
rserpoolPEPolicyDescription (textual description change)
rserpoolPEPolicyWeight (policy weight change, similar to ASAP)
rserpoolPEPolicyLoadDeg (policy load degradation change, similar
to ASAP)
rserpoolPERegistrationLife (registration lifetime change, similar
to ASAP)
rserpoolPUPoolHandle (pool handle of accessed pool change, similar
to ASAP)
rserpoolPUDescription (textual description change)
The security implications of changing these items are similar to
changes via ASAP; the corresponding security implications are
described in the threats document [RFC5355]. Modifying the textual
descriptions of components may result in wrong administrator
decisions upon malicious information.
Dreibholz & Mulik Experimental [Page 42]
RFC 5525 RSerPool MIB Module April 2009
Some of the readable objects in this MIB module (i.e., objects with a
MAX-ACCESS other than not-accessible) may be considered sensitive or
vulnerable in some network environments. It is thus important to
control even GET and/or NOTIFY access to these objects and possibly
to even encrypt the values of these objects when sending them over
the network via SNMP. Read access reveals the same information which
is also available by ASAP and ENRP access. The security implications
of these two protocols are explained in detail by the threats
document [RFC5355].
SNMP versions prior to SNMPv3 did not include adequate security.
Even if the network itself is secure (for example by using IPsec),
even then, there is no control as to who on the secure network is
allowed to access and GET/SET (read/change/create/delete) the objects
in this MIB module.
It is RECOMMENDED that implementers consider the security features as
provided by the SNMPv3 framework (see [RFC3410], section 8),
including full support for the SNMPv3 cryptographic mechanisms (for
authentication and privacy).
Further, deployment of SNMP versions prior to SNMPv3 is NOT
RECOMMENDED. Instead, it is RECOMMENDED to deploy SNMPv3 and to
enable cryptographic security. It is then a customer/operator
responsibility to ensure that the SNMP entity giving access to an
instance of this MIB module is properly configured to give access to
the objects only to those principals (users) that have legitimate
rights to indeed GET or SET (change/create/delete) them.
9. IANA Considerations
The MIB module in this document uses the following IANA-assigned
OBJECT IDENTIFIER values recorded in the SMI Numbers registry:
Descriptor OBJECT IDENTIFIER Value
---------- -----------------------
rserpoolMIB { experimental 125 }
10. Acknowledgments
The authors would like to express a special note of thanks to Phillip
Conrad and Kevin Pinzhoffer for their efforts in the early formation
of this document. Furthermore, the authors would like to thank Bert
Wijnen and Dan Romascanu for their valuable comments on this
document. Finally, the authors would like to thank Nihad Cosic, Dirk
Hoffstadt, Michael Kohnen, Jobin Pulinthanath, Randall Stewart,
Michael Tuexen, and Xing Zhou for their support.
Dreibholz & Mulik Experimental [Page 43]
RFC 5525 RSerPool MIB Module April 2009
11. References
11.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC2578] McCloghrie, K., Ed., Perkins, D., Ed., and J.
Schoenwaelder, Ed., "Structure of Management
Information Version 2 (SMIv2)", STD 58, RFC 2578,
April 1999.
[RFC2579] McCloghrie, K., Ed., Perkins, D., Ed., and J.
Schoenwaelder, Ed., "Textual Conventions for SMIv2",
STD 58, RFC 2579, April 1999.
[RFC2580] McCloghrie, K., Perkins, D., and J. Schoenwaelder,
"Conformance Statements for SMIv2", STD 58, RFC 2580,
April 1999.
[RFC4001] Daniele, M., Haberman, B., Routhier, S., and J.
Schoenwaelder, "Textual Conventions for Internet
Network Addresses", RFC 4001, February 2005.
[RFC5352] Stewart, R., Xie, Q., Stillman, M., and M. Tuexen,
"Aggregate Server Access Protocol (ASAP)", RFC 5352,
September 2008.
[RFC5353] Xie, Q., Stewart, R., Stillman, M., Tuexen, M., and
A. Silverton, "Endpoint Handlespace Redundancy
Protocol (ENRP)", RFC 5353, September 2008.
[RFC5354] Stewart, R., Xie, Q., Stillman, M., and M. Tuexen,
"Aggregate Server Access Protocol (ASAP) and Endpoint
Handlespace Redundancy Protocol (ENRP) Parameters",
RFC 5354, September 2008.
[RFC5356] Dreibholz, T. and M. Tuexen, "Reliable Server Pooling
Policies", RFC 5356, September 2008.
11.2. Informative References
[RFC3237] Tuexen, M., Xie, Q., Stewart, R., Shore, M., Ong, L.,
Loughney, J., and M. Stillman, "Requirements for
Reliable Server Pooling", RFC 3237, January 2002.
Dreibholz & Mulik Experimental [Page 44]
RFC 5525 RSerPool MIB Module April 2009
[RFC3410] Case, J., Mundy, R., Partain, D., and B. Stewart,
"Introduction and Applicability Statements for
Internet-Standard Management Framework", RFC 3410,
December 2002.
[RFC5351] Lei, P., Ong, L., Tuexen, M., and T. Dreibholz, "An
Overview of Reliable Server Pooling Protocols",
RFC 5351, September 2008.
[RFC5355] Stillman, M., Gopal, R., Guttman, E., Sengodan, S.,
and M. Holdrege, "Threats Introduced by Reliable
Server Pooling (RSerPool) and Requirements for
Security in Response to Threats", RFC 5355,
September 2008.
[Dre2006] Dreibholz, T., "Reliable Server Pooling --
Evaluation, Optimization and Extension of a Novel
IETF Architecture", Ph.D. Thesis University of
Duisburg-Essen, Faculty of Economics, Institute for
Computer Science and Business Information Systems,
March 2007, <http://duepublico.uni-duisburg-essen.de/
servlets/DerivateServlet/Derivate-16326/
Dre2006-final.pdf>.
[LCN2005] Dreibholz, T. and E. Rathgeb, "On the Performance of
Reliable Server Pooling Systems", Proceedings of the
30th IEEE Local Computer Networks Conference,
November 2005.
[IJHIT2008] Dreibholz, T. and E. Rathgeb, "An Evaluation of the
Pool Maintenance Overhead in Reliable Server Pooling
Systems", International Journal of Hybrid Information
Technology (IJHIT) Volume 1, Number 2, April 2008.
[RSerPoolPage] Dreibholz, T., "Thomas Dreibholz's RSerPool Page",
<http://tdrwww.iem.uni-due.de/dreibholz/rserpool/>.
[SNMPMIBS] Perkins, D. and E. McGinnis, "Understanding SNMP
MIBs", 1997.
Dreibholz & Mulik Experimental [Page 45]
RFC 5525 RSerPool MIB Module April 2009
Authors' Addresses
Thomas Dreibholz
University of Duisburg-Essen, Institute for Experimental Mathematics
Ellernstrasse 29
45326 Essen, Nordrhein-Westfalen
Germany
Phone: +49-201-1837637
Fax: +49-201-1837673
EMail: dreibh@iem.uni-due.de
URI: http://www.iem.uni-due.de/~dreibh/
Jaiwant Mulik
Delaware State University
CIS Department
Room 306A, Science Center North
1200 N. DuPont Hwy
Dover, DE 19904
USA
Phone: +1-302-857-7910
Fax: +1-302-857-6552
EMail: jaiwant@mulik.com
URI: http://netlab.cis.desu.edu
Dreibholz & Mulik Experimental [Page 46]