<- RFC Index (5601..5700)
RFC 5686
Network Working Group Y. Hiwasaki
Request for Comments: 5686 H. Ohmuro
Category: Standards Track NTT Corporation
October 2009
RTP Payload Format for mU-law EMbedded Codec for Low-delay IP
Communication (UEMCLIP) Speech Codec
Abstract
This document describes the RTP payload format of a mU-law EMbedded
Coder for Low-delay IP communication (UEMCLIP), an enhanced speech
codec of ITU-T G.711. The bitstream has a scalable structure with an
embedded u-law bitstream, also known as PCMU, thus providing a handy
transcoding operation between narrowband and wideband speech.
Status of This Memo
This document specifies an Internet standards track protocol for the
Internet community, and requests discussion and suggestions for
improvements. Please refer to the current edition of the "Internet
Official Protocol Standards" (STD 1) for the standardization state
and status of this protocol. Distribution of this memo is unlimited.
Copyright Notice
Copyright (c) 2009 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the BSD License.
This document may contain material from IETF Documents or IETF
Contributions published or made publicly available before November
10, 2008. The person(s) controlling the copyright in some of this
material may not have granted the IETF Trust the right to allow
modifications of such material outside the IETF Standards Process.
Without obtaining an adequate license from the person(s) controlling
the copyright in such materials, this document may not be modified
outside the IETF Standards Process, and derivative works of it may
Hiwasaki & Ohmuro Standards Track [Page 1]
RFC 5686 RTP Payload Format for UEMCLIP October 2009
not be created outside the IETF Standards Process, except to format
it for publication as an RFC or to translate it into languages other
than English.
Table of Contents
1. Introduction ....................................................2
1.1. Terminology ................................................3
2. Media Format Background .........................................3
3. Payload Format ..................................................5
3.1. RTP Header Usage ...........................................6
3.2. Multiple Frames in an RTP Packet ...........................6
3.3. Payload Data ...............................................7
3.3.1. Main Header .........................................7
3.3.2. Sub-Layer ..........................................10
4. Transcoding between UEMCLIP and G.711 ..........................11
5. Congestion Control Considerations ..............................12
6. Payload Format Parameters ......................................13
6.1. Media Type Registration ...................................13
6.2. Mapping to SDP Parameters .................................14
6.2.1. Mode Specification .................................15
6.3. Offer-Answer Model Considerations .........................16
6.3.1. Offer-Answer Guidelines ............................16
6.3.2. Examples ...........................................17
7. Security Considerations ........................................19
8. IANA Considerations ............................................19
9. References .....................................................19
9.1. Normative References ......................................19
9.2. Informative References ....................................20
1. Introduction
This document specifies the payload format for sending UEMCLIP-
encoded (mU-law EMbedded Coder for Low-delay IP communication) speech
using the Real-time Transport Protocol (RTP) [RFC3550]. UEMCLIP is a
proprietary codec that enhances u-law ITU-T G.711 [ITU-T-G.711] and
that is designed to help the market for smooth transition towards the
forthcoming wideband communication environment while achieving a very
small media transcoding load with the existing terminals, in which
the implementation of G.711 is mandatory.
It should be noted that, generally speaking, codecs are negotiated
and changed using an SDP exchange. Also, [RFC3550] defines general
RTP mixer and translator models, where media transcoding may not take
place at the node. For those cases, the design concept of the
embedded structure is not useful. However, there are other cases
when costly transcoding is unavoidable in commonly deployed types of
Multi-point Control Units (MCUs), which terminate media and RTCP
Hiwasaki & Ohmuro Standards Track [Page 2]
RFC 5686 RTP Payload Format for UEMCLIP October 2009
packets [RFC5117], and when narrowband and wideband terminals
coexist. This embedded bitstream structure can reduce the media
transcoding to a simple bitstream truncation.
The background and the basic idea of the media format is described in
Section 2. The details of the payload format are given in Section 3.
The transcoding issues with G.711 are discussed in Section 4, and the
considerations for congestion control are in Section 5. In
Section 6, the payload format parameters for a media type
registration for UEMCLIP RTP payload format and Session Description
Protocol (SDP) mappings are provided. The security considerations
and IANA considerations are dealt with in Section 7 and Section 8,
respectively.
1.1. Terminology
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in [RFC2119].
2. Media Format Background
UEMCLIP is an enhanced version of u-law ITU-T G.711, otherwise known
as PCMU [RFC4856]. It is targeted at Voice over Internet Protocol
(VoIP) applications, and its main goal is to provide a wideband
communication platform that is highly interoperable with existing
terminals equipped with G.711 and to stimulate the market to
gradually shift to using wideband communication. In widely deployed
multi-point conferencing systems, the packets usually go through
RTCP-terminating (RTP Control Protocol) MCUs, "Topo-RTCP-terminating-
MCU" as defined in [RFC5117]. Because the G.711 bitstream is
embedded in the bitstream, costly media transcoding can be avoided in
this case.
This document does not discuss the implementation details of the
encoder and decoder, but only describes the bitstream format.
Because of its scalable nature, there are a number of sub-bitstreams
(sub-layer) in a UEMCLIP bitstream. By choosing appropriate sub-
layers, the codec can adapt to the following requirements:
o Sampling frequency,
o Number of channels,
o Speech quality, and
o Bit-rate.
Hiwasaki & Ohmuro Standards Track [Page 3]
RFC 5686 RTP Payload Format for UEMCLIP October 2009
The UEMCLIP codec operates at a 20-ms frame, and includes three sub-
coders as shown in Table 1. The core layer is u-law G.711 at 64
kbit/s, and other two are quality and bandwidth enhancement layers
with bit-rate of 16 kbit/s each.
+-------+---------------------+----------+--------------------------+
| Layer | Description | Bit-rate | Coding algorithm |
+-------+---------------------+----------+--------------------------+
| a | G.711 core | 64 | u-law PCM |
| | | | |
| b | Lower-band | 16 | Time domain block |
| | enhancement | | quantization |
| | | | |
| c | Higher-band | 16 | MDCT block quantization |
+-------+---------------------+----------+--------------------------+
Table 1: Sub-Layer Description
Based on these sub-layers, the UEMCLIP codec operates in four modes
as shown in Table 2. Here, "Ch" is the number of channels and "Fs"
is the sampling frequency in kHz. It should be noted that the
current version only supports single-channel operation and there
might be future extensions with multi-channel capabilities. The
absent Modes 2 and 5 are reserved for possible future extension to 32
kHz sampling modes. As the mode definition is expected to grow, any
other modes not defined in this table MUST NOT be used for
compatibility and interoperability reasons.
+------+----+----+-------+-------+-------+-------------+------------+
| Mode | Ch | Fs | Layer | Layer | Layer | Bit-rate | Total |
| | | | a | b | c | w/o headers | bit-rate |
| | | | | | | [kbit/s] | [kbit/s] |
+------+----+----+-------+-------+-------+-------------+------------+
| 0 | 1 | 8 | x | - | - | 64 | 67.2 |
| | | | | | | | |
| 1 | 1 | 16 | x | - | x | 80 | 84.0 |
| | | | | | | | |
| 2 | - | - | - | - | - | - | - |
| | | | | | | | |
| 3 | 1 | 8 | x | x | - | 80 | 84.0 |
| | | | | | | | |
| 4 | 1 | 16 | x | x | x | 96 | 100.8 |
| | | | | | | | |
| 5 | - | - | - | - | - | - | - |
+------+----+----+-------+-------+-------+-------------+------------+
Table 2: Mode Description
Hiwasaki & Ohmuro Standards Track [Page 4]
RFC 5686 RTP Payload Format for UEMCLIP October 2009
The UEMCLIP bitstream contains internal headers and other side-
information apart from the layer data. This results in total bit-
rate larger than the sum of the layers shown in the above table. The
detail of the internal headers and auxiliary information are
described in Section 3.3.1.
Defining the sampling frequency and the number of channels does not
result in a singular mode, i.e., there can be multiple modes for the
same sampling frequency or number of channels. The supported modes
would differ between implementations; thus, the sender and the
receiver must negotiate what mode to use for transmission.
3. Payload Format
As an RTP payload, the UEMCLIP bitstream can contain one or more
frames as shown in Figure 1.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| RTP Header |
+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+
| |
| one or more frames of UEMCLIP |
| |
+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+
Figure 1: RTP Payload Format
The UEMCLIP bitstream has a scalable structure; thus, it is possible
to reconstruct the signal by decoding a part of it. A UEMCLIP frame
is composed of a main header (MH) followed by one or more (up to
three) sub-layers (SLs) as shown in Figure 2.
+--+-------+//-+
|MH| SL #1 |...|
+--+-------+//-+
Figure 2: A UEMCLIP Frame (Bitstream Format)
As a sub-layer, the core layer, i.e., "Layer a", MUST always be
included. It should be noted that the location of the core layer may
or may not immediately follow MH field. The decoder MUST always
refer to the layer indices for proper decoding because the order of
the sub-layers is arbitrary.
Hiwasaki & Ohmuro Standards Track [Page 5]
RFC 5686 RTP Payload Format for UEMCLIP October 2009
The UEMCLIP bitstream does not explicitly include the following
information: mode and sampling frequency (Fs). As described before,
this information MUST be exchanged while establishing a connection,
for example, by means of SDP.
3.1. RTP Header Usage
Each RTP packet starts with a fixed RTP header, as explained in
[RFC3550]. The following fields of the RTP fixed header used
specifically for UEMCLIP streams are emphasized:
Payload type: The assignment of an RTP payload type for this packet
format is outside the scope of this document; however, it is
expected that a payload type in the dynamic range shall be
assigned.
Timestamp: This encodes the sampling instant of the first speech
signal sample in the RTP data packet. For UEMCLIP streams, the
RTP timestamp MUST advance based on a clock either at 8000 or
16000 (Hz). In cases where the audio sampling rate can change
during a session, the RTP timestamp rate MUST be equal to the
maximum rate (in Hz) given in the mode range (see Section 6.2.1).
This implies that the RTP timestamp rate for UEMCLIP payload type
MUST NOT change during a session. For example, for a UEMCLIP
stream with 8-kHz audio sampling, where a transition to a 16-kHz
audio sampling mode is allowed, the RTP time stamp must always
advance using the 16-kHz clock rate. For a fixed audio sampling
mode, the RTP timestamp rate should be either 8 or 16 kHz,
depending on the sampling rate.
Marker bit: If the codec is used for applications with discontinuous
transmission (DTX, or silence compression), the first packet after
a silence period during which packets have not been transmitted
contiguously SHOULD have the marker bit in the RTP data header set
to one. The marker bit in all other packets MUST be zero.
Applications without DTX MUST set the marker bit to zero.
3.2. Multiple Frames in an RTP Packet
More than one UEMCLIP frame may be included in a single RTP packet by
a sender. However, senders have the following additional
restrictions:
o A single RTP packet SHOULD NOT include more UEMCLIP frames than
will fit in the path MTU.
o All frames contained in a single RTP packet MUST be of the same
mode.
Hiwasaki & Ohmuro Standards Track [Page 6]
RFC 5686 RTP Payload Format for UEMCLIP October 2009
o Frames MUST NOT be split between RTP packets.
It is RECOMMENDED that the number of frames contained within an RTP
packet be consistent with the application. Since UEMCLIP is designed
for telephony applications where delay has a great impact on the
quality, then fewer frames per packet for lower delay, is preferable.
3.3. Payload Data
In a UEMCLIP bitstream, all numbers are encoded in a network byte
order.
3.3.1. Main Header
The main header (MH) is placed at the top of a frame and has a size
of 6 bytes. The content of the main header is shown in Figure 3.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| MX | PC |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| PC(cont'd) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 3: UEMCLIP Main Header Format (MH)
Mixing information (MX): 8 bits
Mixing information field. This field is only relevant when Topo-
RTCP-terminating-MCUs are utilized to interpret these fields. See
Section 3.3.1.1 for details of the fields.
Packet-loss Concealment information (PC): 40 bits
Packet-loss concealment (PLC) information field. See
Section 3.3.1.2.
3.3.1.1. Mixing Information Field
0 1 2 3 4 5 6 7
+-+-+-+-+-+-+-+-+
|C|R|V| PW1 |
|1|1|1| |
+-+-+-+-+-+-+-+-+
Figure 4: Mixing Information Field (MX)
Hiwasaki & Ohmuro Standards Track [Page 7]
RFC 5686 RTP Payload Format for UEMCLIP October 2009
Check bit #1 (C1): 1 bit
Validity flag of V1 and PW1. This bit being "1" indicates that
both parameters are valid, and "0" indicates that the parameters
should be ignored. If any of these parameters is invalid, this
bit should be set to "0". This flag is mainly intended for a
UEMCLIP-conscious Topo-RTCP-terminating-MCU. This flag should be
set to "0" in case of upward transcoding from G.711 (see
Section 4).
Reserved bit #1 (R1): 1 bit
This bit should be ignored. The default of this bit is 0.
VAD flag #1 (V1): 1 bit
Voice activity detection flag of the current frame, designed to be
used for MCU operations. This flag being "1" indicates that the
frame is an active (voice) segment, and "0" indicates that it is
an inactive (non-voice) or a silent segment. This flag is
specifically designed for mixing information. DTX judgment based
this flag is not recommended.
Power #1 (PW1): 5 bits
Signal power code of the current frame. The code is obtained by
calculating a root mean square (RMS) of "Layer a" and encoding
this RMS using G.711 u-law [ITU-T-G.711]. Denoting the encoded
RMS as R, then PW1 is obtained by PW1 = ((~R)>>2) & 0x1F, where
"~", ">>", "&" are one's complement arithmetic, right SHIFT, and
bitwise AND operators, respectively.
3.3.1.2. PLC Information Field
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|C|R2 |V| K |U| P1 |U| P2 | PW2 |
|2| |2| |1| |2| | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| R3 |
| |
+-+-+-+-+-+-+-+-+
Figure 5: PLC Information Field (PC)
Hiwasaki & Ohmuro Standards Track [Page 8]
RFC 5686 RTP Payload Format for UEMCLIP October 2009
Check bit #2 (C2): 1 bit
Validity flag of V2, K, U1, P1, U2, P2, and PW2. If the flag is
"1", it means that all these parameters are valid, and "0" means
that the parameters should be ignored. If any of these parameters
is invalid, this bit should be set to "0". Similarly to C1, this
flag should be set to "0" in case of upward transcoding from G.711
(see Section 4).
Reserved bit #2 (R2): 2 bits
These bits should be ignored. The default of these bits are 0.
VAD flag #2 (V2): 1 bit
Voice activity detection flag of the current frame, designed to be
used for packet-loss concealment. This might not be the same as
V1 in the mixing information, and might not be synchronous to the
marker bit in the RTP header. DTX judgment based this flag is not
recommended.
Frame indicator (K): 4 bits
This value indicates the frame offset of U2, P2, and PW2. Since
it is a better idea to carry the speech feature parameters as PLC
information in a different frame to maintain the speech quality,
this frame offset value gives with which frame the parameters are
to be associated. The value ranges between "0" and "15". If the
current frame number is N, for example, the value K indicates that
U2, P2, and PW2 are associated with the frame of N-K. The frame
indicator is equal to the difference in the RTP sequence number
when one UEMCLIP frame is contained in a single RTP packet.
V/UV flag #1 (U1): 1 bit
Voiced/Unvoiced signal indicator of the current frame. This flag
being "0" indicates that the frame is a voiced signal segment, and
"1" indicates that it is an unvoiced signal segment.
Pitch lag #1 (P1): 7 bits
Pitch code of the current frame. The actual pitch lag is
calculated as P1+20 samples in 8-kHz sampling rate. Pitch lag
must be 20 <= pitch length <= 120. Codes ranging between "0x65"
and "0x7F" are not used. To obtain the pitch lag, any pitch
estimation method can be used, such as the one used in G.711
Appendix I [ITU-T-G.711Appendix1].
Hiwasaki & Ohmuro Standards Track [Page 9]
RFC 5686 RTP Payload Format for UEMCLIP October 2009
V/UV flag #2 (U2): 1 bit
Voiced/Unvoiced signal indicator of the offset frame. This flag
being "0" indicates that the frame is a voiced signal segment, and
"1" indicates that it is an unvoiced signal segment. The offset
value is defined as K.
Pitch lag #2 (P2): 7 bits
Pitch code of the offset frame. The offset value is defined as K.
The calculation method is identical to "P1", except that it is
based on the signal of offset frame.
Power #2 (PW2): 8 bits
Signal power code of the offset frame. The offset value is
defined as K.
Reserved bits #3 (R3): 8 bits
These bits should be ignored. The default of all bits are "0".
3.3.2. Sub-Layer
Sub-layer (SL) is a sub-header followed by layer bitstreams, as shown
in Figure 6. The sub-header indicates the layer location and the
number of bytes.
0 1 2
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 . . .
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+//-+-+-+
|CI |FI |QI |R4 | SB | LD ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+//-+-+-+
Figure 6: Sub-Layer Format (SL)
Channel index (CI): 2 bits
Indicates the channel number. For all modes given in Table 2,
this should be "0". The detail is given in Table 3.
Frequency index (FI): 2 bits
Indicates the frequency number. "0" means that the layer is in the
base frequency band, higher number means that the layer is in
respective frequency band. The detail is given in Table 3.
Hiwasaki & Ohmuro Standards Track [Page 10]
RFC 5686 RTP Payload Format for UEMCLIP October 2009
Quality index (QI): 2 bits
Indicates the quality layer number. "0" means that the layer is in
the base layer, and higher number means that the layer is in
respective quality layer. The detail is given in Table 3.
Reserved #4 (R4): 2 bits
Not used (reserved). The default value is "0".
Sub-layer Size (SB): 8 bits
Indicates the byte size of the following sub-layer data.
Layer Data (LD): SB*8 bits
The actual sub-layer data.
For all the layers shown in Table 1, the layer indices are shown in
Table 3.
+-------+----+----+----+
| Layer | CI | FI | QI |
+-------+----+----+----+
| a | 0 | 0 | 0 |
| | | | |
| b | 0 | 0 | 1 |
| | | | |
| c | 0 | 1 | 0 |
+-------+----+----+----+
Table 3: Layer Indices
4. Transcoding between UEMCLIP and G.711
As given in Section 2, the u-law-encoded G.711 bitstream (Layer a) is
the core layer of a UEMCLIP bitstream, and is always embedded. This
means that media transcoding from the UEMCLIP bitstream to G.711 does
not have to undergo decoding and re-encoding procedures, but simple
extraction would suffice. However, this does not apply for the
reverse procedure, i.e., transcoding from G.711 to UEMCLIP, because
the auxiliary information in the main header (MH) must be assigned
separately. It should be noted that this media transcoding is useful
for a Media Translator (Topo-Media-Translator) or a Point-to-
Multipoint Using RTCP Terminating MCU (Topo-RTCP-terminating-MCU) in
[RFC5117], and all the requirements apply. This means that a
transcoding device of this sort MUST rewrite RTCP packets, together
with the RTP media packets.
Hiwasaki & Ohmuro Standards Track [Page 11]
RFC 5686 RTP Payload Format for UEMCLIP October 2009
The transcoding from UEMCLIP to u-law G.711 can be done easily by
finding an appropriate sub-layer. Within a frame, the transcoder
should look for a sub-layer with a layer index of "0x00", and
subsequent LD that has a size of SB*8 bits (UEMCLIP has a 20-ms frame
thus, SB=160) are the actual G.711 bitstream data. It should be
noted that the transcoder should not always expect the core layer to
be located right after the main header.
On the other hand, the transcoding from G.711 to UEMCLIP is not
entirely straightforward. Since there are no means to generate
enhancement sub-layers, a G.711 bitstream can only be converted to
UEMCLIP Mode 0 bitstream. If the original G.711 bitstream is encoded
in A-law, it should first be converted to u-law to become the core
layer. Because a UEMCLIP frame size is 20 ms, a u-law-encoded G.711
bitstream MUST be a 160-sample chunk to become a core layer. For the
main header contents, when the UEMCLIP encoder is not available, it
should follow these guidelines:
o The check bits for mixing and PLC (C1 and C2) are set to 0.
o The reserved bits (R1 to R3) in MH are set to respective default
values.
For the core layer (i.e., u-law G.711 bitstream), it should have the
following sub-layer header:
o All CI, FI, QI, and R4 MUST be 0.
o Sub-layer size (SB) MUST be 160 for a 20-ms frame.
5. Congestion Control Considerations
The general congestion control considerations for transporting RTP
data also apply to UEMCLIP over RTP [RFC3550] as well as any
applicable RTP profile like Audio-Visual Profile (AVP) [RFC3551].
The bandwidth of a UEMCLIP bitstream can be reduced by changing to
lower-bit-rate modes. The embedded layer structure of UEMCLIP may
help to control congestion, when dynamic mode changing (see
Section 6.2.1) is available, and the range of modes is obtained by
offer-answer negotiation as given in Section 6.3. It should be noted
that this involves proper RTCP handling when the bit-rate is modified
in an RTP translator or a mixer [RFC3550].
Hiwasaki & Ohmuro Standards Track [Page 12]
RFC 5686 RTP Payload Format for UEMCLIP October 2009
Packing more frames in each RTP payload can reduce the number of
packets sent, and hence the overhead from IP/UDP/RTP headers, at the
expense of increased delay and reduced error robustness against
packet losses. It should be treated with care because increased
delay means reduced quality.
6. Payload Format Parameters
6.1. Media Type Registration
This registration is done using the template defined in [RFC4288] and
following [RFC4855].
Media type name: audio
Media subtype name: UEMCLIP
Required parameters:
Rate: Defines the sampling rate, and it MUST be either 8000 or
16000. See Section 6.2.1 "Mode specification" of RFC 5686
(this RFC) for details.
Optional parameters:
ptime: See RFC 4566 [RFC4566].
maxptime: See RFC 4566 [RFC4566].
mode: Indicates the range of dynamically changeable modes during
a session. Possible values are a comma-separated list of modes
from the supported mode set: 0, 1, 3, and 4. If only one mode
is specified, it means that the mode must not be changed during
the session. When not specified, the mode transmission
defaults to a singular mode as specified in Table 4. See
Section 6.2.1 "Mode specification" of RFC 5686 (this RFC) for
details.
Encoding considerations: This media type is framed and contains
binary data. See Section 4.8 of RFC 4288.
Security considerations: See Section 7 "Security Considerations" of
RFC 5686 (this RFC).
Interoperability considerations: This media may be readily
transcoded to u-law-encoded ITU-T G.711. See Section 4
"Transcoding between UEMCLIP and G.711" of RFC 5686 (this RFC).
Hiwasaki & Ohmuro Standards Track [Page 13]
RFC 5686 RTP Payload Format for UEMCLIP October 2009
Published specification: RFC 5686 (this RFC)
Applications that use this media type: Audio and video streaming and
conferencing tools.
Additional information: None
Intended usage: COMMON
Restrictions on usage: This media type depends on RTP framing, and
hence is only defined for transfer via RTP.
Person & email address to contact for further information:
Yusuke Hiwasaki <hiwasaki.yusuke@lab.ntt.co.jp>
Author: Yusuke Hiwasaki
Change Controller: IETF Audio/Video Transport Working Group
delegated from the IESG
6.2. Mapping to SDP Parameters
The media types audio/UEMCLIP are mapped to fields in the Session
Description Protocol (SDP) [RFC4566] as follows:
Media name: The "m=" line of SDP MUST be audio.
Encoding name: Registered media subtype name should be used for the
"a=rtpmap" line.
Sampling Frequency: Depending on the mode, clock rate (sampling
frequency) specified in "a=rtpmap" MUST be selected from the ones
defined in Table 2. See Section 6.2.1 for details.
Encoding parameters: Since this is an audio stream, the encoding
parameters indicate the number of audio channels, and this SHOULD
default to "1", as selected from the ones defined in Table 2.
This is OPTIONAL.
Packet time: A frame length of any UEMCLIP is 20 ms, thus the
argument of "a=ptime" SHOULD be a multiple of "20". When not
listed in SDP, it should also default to the minimum size: "20".
UMECLIP specific: Any description specific to UEMCLIP is defined in
the Format Specification Parameters ("a=fmtp"). Each parameter
MUST be separated with ";", and if any attribute (value) exists,
it MUST be defined with "=". For compatibility reasons, any
application/terminal MUST ignore any parameters that it does not
Hiwasaki & Ohmuro Standards Track [Page 14]
RFC 5686 RTP Payload Format for UEMCLIP October 2009
understand. This is to ensure the upper-compatibility with
parameters added in future enhancements. The mode specification
should be made here (see Section 6.2.1).
6.2.1. Mode Specification
Since UEMCLIP codec can operate in number of modes (bit-rates), it is
desirable to specify the range of modes at which an encoder or a
decoder can operate. When exchanging SDP messages, an offerer should
specify all possible combinations of mode numbers as arguments to
"mode=" in "a=fmtp" line, delimited by commas ",". In case of
specifying multiple modes, those SHOULD appear in the descending
priority order.
Although UEMCLIP decoders SHOULD accept bitstreams in any modes, an
implementation may fail to adapt to the dynamic mode changes during a
session. For this reason, an application may choose to operate
either with one fixed mode or with multiple modes that can be
dynamically changed. If the mode is to be fixed and changes are not
allowed, this can be indicated by specifying a single mode per
payload type.
The mode numbers that can be specified in a payload type as arguments
to "mode" are restricted by a combination of a clock rate and a
number of audio channels. This is because SDP binds a payload type
to a combination of a sampling frequency and a number of audio
channels. Table 4 gives selectable mode numbers that are attributed
with clock rates. When mode specifications are not given at all, a
payload type MUST default to a single mode using the default value
specified in this table.
+------------+----------+------------------+--------------+
| Clock rate | Channels | Selectable modes | Default mode |
+------------+----------+------------------+--------------+
| 8000 | 1 | 0,3 | 0 |
| | | | |
| 16000 | 1 | 0,1,3,4 | 1 |
+------------+----------+------------------+--------------+
Table 4: Default Modes
It should be noted that a mode attributed with a larger sampling
frequency (Fs) is not used in conjunction with smaller clock rates
specified in "a=rtpmap". This means that Modes 0 and 3 can be
specified in a payload type having a clock rate of both 8000 and
16000 in "a=rtpmap", but Modes 1 and 4 cannot be specified with one
having a clock rate of 8000.
Hiwasaki & Ohmuro Standards Track [Page 15]
RFC 5686 RTP Payload Format for UEMCLIP October 2009
6.3. Offer-Answer Model Considerations
6.3.1. Offer-Answer Guidelines
The procedures related to exchanging SDP messages MUST follow
[RFC3264]. The following is a detailed list on the semantics of
using the UEMCLIP payload format in an offer-answer exchange.
o An offerer SHOULD offer every possible combination of UEMCLIP
payload type it can handle, i.e., sampling frequency, channel
number, and fmtp parameters, in a preferred order. When the
transmission bandwidth is restricted, it MUST be offered in
accordance to the restriction.
o When multiple UEMCLIP payload types are offered, it is RECOMMENDED
that the answerer select a single UEMCLIP payload type and answer
it back.
o In a UEMCLIP payload type, an answerer MUST answer back suitable
mode number(s) as a subset of what has been offered. This means
that there is a symmetry assumption on sent and received streams,
and the offerer MUST NOT send in modes that it does not offer.
o In an offering/answering SDP, any fmtp parameters that are not
known MUST be ignored. If any unknown/undefined parameters should
be offered, an answerer MUST delete the entry from the answer
message.
o A receiver of an SDP message MUST only use specified payload types
and modes. When a mode specification is missing, i.e., a mode is
not specified at all, the session MUST default to one single mode
without mode changes during a session. For this case, the default
mode values, as shown in Table 4, MUST be used based on the
sampling frequency and number of channels. This table must be
looked up only when there are no mode specifications; thus, the
offerer/answerer MUST NOT assume that the default modes are always
available when it is not in the specified list of modes.
o When an offered condition does not fit an answerer's capabilities,
it naturally MUST NOT answer any of the conditions, and the
session MAY proceed to re-INVITE, if possible. If a condition
(mode) is decided upon, an offerer and an answerer MUST transmit
on this condition.
Hiwasaki & Ohmuro Standards Track [Page 16]
RFC 5686 RTP Payload Format for UEMCLIP October 2009
6.3.2. Examples
When an offerer indicates that he/she wishes to dynamically switch
between modes (0,1,3, and 4) during a session, an example of an
offered SDP could be:
v=0
o=john 51050101 51050101 IN IP4 offhost.example.com
s=-
c=IN IP4 offhost.example.com
t=0 0
m=audio 5004 RTP/AVP 96
a=rtpmap:96 UEMCLIP/16000/1
a=fmtp:96 mode=4,1,3,0
It should be noted that the listed modes appears in the offerer's
preference.
When an answerer can only operate in Modes 1 and 0 but can
dynamically switch between those modes during a session, an answerer
MUST delete the entries of Mode 3 and 4, and answer back as:
v=0
o=lena 549947322 549947322 IN IP4 anshost.example.org
s=-
c=IN IP4 anshost.example.org
t=0 0
m=audio 5004 RTP/AVP 96
a=rtpmap:96 UEMCLIP/16000/1
a=fmtp:96 mode=1,0
As a result, both would start communicating in either Mode 1 or 0,
and can dynamically switch between those modes during the session.
On the other hand, when the answerer is capable of communicating
either in Modes 1 or 0, and cannot switch between modes during a
session, an example of such answer is as follows:
v=0
o=lena 549947322 549947322 IN IP4 anshost.example.org
s=-
c=IN IP4 anshost.example.org
t=0 0
m=audio 5004 RTP/AVP 96
a=rtpmap:96 UEMCLIP/16000/1
a=fmtp:96 mode=1
Hiwasaki & Ohmuro Standards Track [Page 17]
RFC 5686 RTP Payload Format for UEMCLIP October 2009
As a result, both will start communicating in Mode 1. It should be
noted that mode change during this session is not allowed because the
answerer responded with a single mode, and answerer selected Mode 1
above Mode 0 according to the offered order.
If an offerer does not want a mode change during a session but is
capable of receiving either Modes 4 or 1 bitstreams, the SDP should
somewhat look like:
v=0
o=john 51050101 51050101 IN IP4 offhost.example.com
s=-
c=IN IP4 offhost.example.com
t=0 0
m=audio 5004 RTP/AVP 96 97
a=rtpmap:96 UEMCLIP/16000/1
a=fmtp:96 mode=4
a=rtpmap:97 UEMCLIP/16000/1
a=fmtp:97 mode=1
and if the answerer prefers to communicate in Mode 1, an answer would
be:
v=0
o=lena 549947322 549947322 IN IP4 anshost.example.org
s=-
c=IN IP4 anshost.example.org
t=0 0
m=audio 5004 RTP/AVP 97
a=rtpmap:97 UEMCLIP/16000/1
a=fmtp:97 mode=1
Please note that it is RECOMMENDED to select a single UEMCLIP payload
type for answers.
The "ptime" attribute is used to denote the desired packetization
interval. When not specified, it SHOULD default to 20. Since
UEMCLIP uses 20-ms frames, ptime values of multiples of 20 imply
multiple frames per packet. In the example below, the ptime is set
to 60, and this means that offerer wants to receive 3 frames in each
packet.
Hiwasaki & Ohmuro Standards Track [Page 18]
RFC 5686 RTP Payload Format for UEMCLIP October 2009
v=0
o=kosuke 2890844730 2890844730 IN IP4 anotherhost.example.com
s=-
c=IN IP4 anotherhost.example.com
t=0 0
m=audio 5004 RTP/AVP 96
a=ptime:60
a=rtpmap:96 UEMCLIP/16000/1
When mode specification is not present, it should default to a fixed
mode, and in this case, Mode 1 (see Section 6.2.1).
7. Security Considerations
RTP packets using the payload format defined in this specification
are subject to the security considerations discussed in the RTP
specification [RFC3550] and any appropriate profiles. This implies
that confidentiality of the media streams is achieved by encryption
unless the applicable profile specifies other means.
A potential denial-of-service threat exists for data encoding using
compression techniques that have non-uniform receiver-end
computational load. The attacker can inject pathological datagrams
into the stream that are complex to decode and cause the receiver
output to become overloaded. However, the UEMCLIP covered in this
document do not exhibit any significant non-uniformity.
Another potential threat is memory attacks by illegal layer indices
or byte numbers. The implementor of the decoder should always be
aware that the indicated numbers may be corrupted and not point to
the right sub-layer, and they may force reading beyond the bitstream
boundaries. It is advised that a decoder implementation reject
layers of such indices.
8. IANA Considerations
One new media subtype (audio/UEMCLIP) has been registered by IANA.
For details, see Section 6.1.
9. References
9.1. Normative References
[ITU-T-G.711]
International Telecommunications Union, "Pulse code
modulation (PCM) of voice frequencies", ITU-
T Recommendation G.711, November 1988.
Hiwasaki & Ohmuro Standards Track [Page 19]
RFC 5686 RTP Payload Format for UEMCLIP October 2009
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC3264] Rosenberg, J. and H. Schulzrinne, "An Offer/Answer Model
with Session Description Protocol (SDP)", RFC 3264,
June 2002.
[RFC3550] Schulzrinne, H., Casner, S., Frederick, R., and V.
Jacobson, "RTP: A Transport Protocol for Real-Time
Applications", STD 64, RFC 3550, July 2003.
[RFC3551] Schulzrinne, H. and S. Casner, "RTP Profile for Audio and
Video Conferences with Minimal Control", STD 65, RFC 3551,
July 2003.
[RFC4288] Freed, N. and J. Klensin, "Media Type Specifications and
Registration Procedures", BCP 13, RFC 4288, December 2005.
[RFC4566] Handley, M., Jacobson, V., and C. Perkins, "SDP: Session
Description Protocol", RFC 4566, July 2006.
[RFC4855] Casner, S., "Media Type Registration of RTP Payload
Formats", RFC 4855, February 2007.
[RFC4856] Casner, S., "Media Type Registration of Payload Formats in
the RTP Profile for Audio and Video Conferences",
RFC 4856, February 2007.
[RFC5117] Westerlund, M. and S. Wenger, "RTP Topologies", RFC 5117,
January 2008.
9.2. Informative References
[ITU-T-G.711Appendix1]
International Telecommunications Union, "Pulse code
modulation (PCM) of voice frequencies, Appendix I: A high
quality low-complexity algorithm for packet loss
concealment with G.711", ITU-T Recommendation G.711
Appendix I, September 1999.
Hiwasaki & Ohmuro Standards Track [Page 20]
RFC 5686 RTP Payload Format for UEMCLIP October 2009
Authors' Addresses
Yusuke Hiwasaki
NTT Corporation
3-9-11 Midori-cho,
Musashino-shi
Tokyo 180-8585
Japan
Phone: +81(422)59-4815
EMail: hiwasaki.yusuke@lab.ntt.co.jp
Hitoshi Ohmuro
NTT Corporation
3-9-11 Midori-cho,
Musashino-shi
Tokyo 180-8585
Japan
Phone: +81(422)59-2151
EMail: ohmuro.hitoshi@lab.ntt.co.jp
Hiwasaki & Ohmuro Standards Track [Page 21]