<- RFC Index (7001..7100)
RFC 7052
Internet Engineering Task Force (IETF) G. Schudel
Request for Comments: 7052 Cisco Systems
Category: Experimental A. Jain
ISSN: 2070-1721 Juniper Networks
V. Moreno
Cisco Systems
October 2013
Locator/ID Separation Protocol (LISP) MIB
Abstract
This document defines the MIB module that contains managed objects to
support the monitoring devices of the Locator/ID Separation Protocol
(LISP). These objects provide information useful for monitoring LISP
devices, including determining basic LISP configuration information,
LISP functional status, and operational counters and other
statistics.
Status of This Memo
This document is not an Internet Standards Track specification; it is
published for examination, experimental implementation, and
evaluation.
This document defines an Experimental Protocol for the Internet
community. This document is a product of the Internet Engineering
Task Force (IETF). It represents the consensus of the IETF
community. It has received public review and has been approved for
publication by the Internet Engineering Steering Group (IESG). Not
all documents approved by the IESG are a candidate for any level of
Internet Standard; see Section 2 of RFC 5741.
Information about the current status of this document, any errata,
and how to provide feedback on it may be obtained at
http://www.rfc-editor.org/info/rfc7052.
Schudel, et al. Experimental [Page 1]
RFC 7052 LISP MIB October 2013
Copyright Notice
Copyright (c) 2013 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Requirements Notation . . . . . . . . . . . . . . . . . . . . 3
3. The Internet-Standard Management Framework . . . . . . . . . . 3
4. Definition of Terms . . . . . . . . . . . . . . . . . . . . . 4
5. LISP MIB Objectives . . . . . . . . . . . . . . . . . . . . . 5
6. Structure of LISP MIB Module . . . . . . . . . . . . . . . . . 5
6.1. Overview of Defined Notifications . . . . . . . . . . . . 5
6.2. Overview of Defined Tables . . . . . . . . . . . . . . . . 5
7. LISP MIB Definitions . . . . . . . . . . . . . . . . . . . . . 7
8. Relationship to Other MIB Modules . . . . . . . . . . . . . . 62
8.1. MIB Modules Required for IMPORTS . . . . . . . . . . . . . 62
9. Security Considerations . . . . . . . . . . . . . . . . . . . 63
10. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 64
11. References . . . . . . . . . . . . . . . . . . . . . . . . . . 64
11.1. Normative References . . . . . . . . . . . . . . . . . . . 64
11.2. Informative References . . . . . . . . . . . . . . . . . . 65
Appendix A. Acknowledgments . . . . . . . . . . . . . . . . . . . 66
Schudel, et al. Experimental [Page 2]
RFC 7052 LISP MIB October 2013
1. Introduction
This document describes the Management Information Base (MIB) module
for use with network management protocols in the Internet community.
Specifically, the MIB for managing devices that support the
Locator/ID Separation Protocol (LISP) is described.
LISP [RFC6830] specifies a network-based architecture and mechanisms
that implement a new semantic for IP addressing using two separate
name spaces: Endpoint Identifiers (EIDs), used within sites, and
Routing Locators (RLOCs), used on the transit networks that make up
the Internet infrastructure. To achieve this separation, LISP
defines protocol mechanisms for mapping from EIDs to RLOCs.
From a data-plane perspective, LISP traffic is handled exclusively at
the network layer by devices performing Ingress Tunnel Router (ITR)
and Egress Tunnel Router (ETR) LISP functions. Data-plane operations
performed by these devices are described in [RFC6830]. Additionally,
data-plane interworking between legacy (Internet) and LISP sites is
implemented by devices performing Proxy ITR (PITR) and Proxy ETR
(PETR) functions. The data-plane operations of these devices is
described in [RFC6832].
From a control-plane perspective, LISP employs mechanisms related to
creating, maintaining, and resolving mappings from EIDs to RLOCs.
LISP ITRs, ETRs, PITRs, and PETRs perform specific control-plane
functions, and these control-plane operations are described in
[RFC6830]. Additionally, LISP infrastructure devices supporting LISP
control-plane functionality include Map-Servers and Map-Resolvers,
and the control-plane operations of these devices are described in
[RFC6833].
2. Requirements Notation
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in
[RFC2119].
3. The Internet-Standard Management Framework
For a detailed overview of the documents that describe the current
Internet-Standard Management Framework, please refer to section 7 of
RFC 3410 [RFC3410].
Managed objects are accessed via a virtual information store, termed
the Management Information Base or MIB. MIB objects are generally
accessed through the Simple Network Management Protocol (SNMP).
Schudel, et al. Experimental [Page 3]
RFC 7052 LISP MIB October 2013
Objects in the MIB are defined using the mechanisms defined in the
Structure of Management Information (SMI). This memo specifies a MIB
module that is compliant to the SMIv2, which is described in STD 58,
RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC 2580
[RFC2580].
4. Definition of Terms
This document does not define any new terms. All terms used in this
document are listed here for completeness; the authoritative
definition of each term can be found in the definition section of the
respective specified reference.
Endpoint ID (EID): [RFC6830]
Routing Locator (RLOC): [RFC6830]
EID-to-RLOC Cache: [RFC6830]
EID-to-RLOC Database: [RFC6830]
Ingress Tunnel Router (ITR): [RFC6830]
Egress Tunnel Router (ETR): [RFC6830]
xTR: [RFC6830]
Proxy ITR (PITR): [RFC6832]
Proxy ETR (PETR): [RFC6832]
LISP Site: [RFC6830]
Map-Server: [RFC6833]
Map-Resolver: [RFC6833]
Map-Request: [RFC6833]
Map-Reply: [RFC6833]
Negative Map-Reply: [RFC6833]
Schudel, et al. Experimental [Page 4]
RFC 7052 LISP MIB October 2013
5. LISP MIB Objectives
The objectives for this LISP MIB module are to provide a read-only
mechanism to support the following functions:
o Provide a means for obtaining (read-only) a current status of LISP
features enabled on a device, and (read-only) a current status of
configuration attributes related to those features. As one
example, this MIB could determine the ON/OFF status of LISP
features such as ITR, ETR, PITR, PETR, MS, or MR support,
specifically as related to IPv4 or IPv6 address families as well
as the LISP Canonical Address Format (LCAF) [LCAF] with IANA
assigned Address Family Number 16387. Other examples could
include obtaining the (read-only) status of whether RLOC-Probing
is enabled, obtaining the status of whether the use of a PETR is
configured, and obtaining the (read-only) values of other related
attributes such as the map-cache limit value, or a mapping time-
to-live (TTL) value.
o Provide a means for obtaining (read-only) the current attributes
of various LISP tables, such as the EID-to-RLOC policy data
contained in the map-cache, or the local EID-to-RLOC policy data
contained in the mapping-database.
o Provide a means for obtaining (read-only) the current operational
statistics of various LISP functions, such as the number of
packets encapsulated and decapsulated by the device. Other
counters of operational interest, depending on LISP function,
include things like the current number of map-cache entries, and
the total number and rate of map-requests received and sent by the
device.
6. Structure of LISP MIB Module
6.1. Overview of Defined Notifications
No LISP MIB notifications are defined.
6.2. Overview of Defined Tables
The LISP MIB module is composed of the following tables of objects:
lispFeatures - This table provides information representing the
various lisp features that can be enabled on LISP devices.
lispIidToVrf - This table provides information representing the
mapping of a LISP Instance ID to a VRF (Virtual Routing and
Forwarding).
Schudel, et al. Experimental [Page 5]
RFC 7052 LISP MIB October 2013
lispGlobalStats - This table provides global statistics for a given
Instance ID per address family on a LISP device.
lispMappingDatabase - This table represents the EID-to-RLOC database
that contains the EID-Prefix to RLOC mappings configured on an
ETR. In general, this table would be representative of all such
mappings for a given site to which this device belongs.
lispMappingDatabaseLocator - This table represents the set of
routing locators contained in the EID-to-RLOC database configured
on an ETR.
lispMapCache - This table represents the short-lived, on-demand
table maintained on an ITR that stores, tracks, and times-out EID-
to-RLOC mappings.
lispMapCacheLocator - This table represents the set of locators per
EID-Prefix contained in the map-cache table of an ITR.
lispConfiguredLocator - This table represents the set of routing
locators configured on a LISP device.
lispEidRegistration - This table provides the properties of each
EID-Prefix that is registered with this device when configured to
be a Map-Server.
lispEidRegistrationEtr - This table provides the properties of the
different ETRs that send registers, for a given EID-Prefix, to
this device when configured to be a Map-Server.
lispEidRegistrationLocator - This table provides the properties of
the different locators per EID prefix that is registered with this
device when configured to be a Map-Server.
lispUseMapServer - This table provides the properties of all Map-
Servers that this device is configured to use.
lispUseMapResolver - This table provides the properties of all Map-
Resolvers that this device is configured to use.
lispUseProxyEtr - This table provides the properties of all Proxy
ETRs that this device is configured to use.
Schudel, et al. Experimental [Page 6]
RFC 7052 LISP MIB October 2013
7. LISP MIB Definitions
LISP-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE,
mib-2, Unsigned32, Counter64,
Integer32, TimeTicks FROM SNMPv2-SMI -- RFC 2578
TruthValue, TEXTUAL-CONVENTION,
TimeStamp FROM SNMPv2-TC -- RFC 2579
MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF -- RFC 2580
MplsL3VpnName
FROM MPLS-L3VPN-STD-MIB -- RFC 4382
AddressFamilyNumbers
FROM IANA-ADDRESS-FAMILY-NUMBERS-MIB;
-- http://www.iana.org/assignments/ianaaddressfamilynumbers-mib
lispMIB MODULE-IDENTITY
LAST-UPDATED "201310210000Z" -- 21 October 2013
ORGANIZATION
"IETF Locator/ID Separation Protocol (LISP) Working Group"
CONTACT-INFO
"Email: lisp@ietf.org
WG charter:
http://datatracker.ietf.org/wg/lisp/charter/"
DESCRIPTION
"This MIB module contains managed objects to support
monitoring devices that support the Locator/ID Separation
Protocol (LISP).
Copyright (c) 2013 IETF Trust and the persons identified
as authors of the code. All rights reserved.
Redistribution and use in source and binary forms, with
or without modification, is permitted pursuant to, and
subject to the license terms contained in, the Simplified
BSD License set forth in Section 4.c of the IETF Trust's
Legal Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info)."
REVISION "201310210000Z" -- 21 October 2013
DESCRIPTION "Initial version of the IETF LISP-MIB module.
Published as RFC 7052."
::= { mib-2 220 }
--
-- Textual Conventions
--
Schudel, et al. Experimental [Page 7]
RFC 7052 LISP MIB October 2013
LispAddressType ::= TEXTUAL-CONVENTION
DISPLAY-HINT "39a"
STATUS current
DESCRIPTION
"LISP architecture can be applied to a wide variety of
address-families. This textual-convention is a generalization
for representing addresses belonging to those address-families.
For convenience, this document refers to any such address as a
LISP address. LispAddressType textual-convention consists of
the following four-tuple:
1. IANA Address Family Number: A field of length 2 octets,
whose value is of the form following the assigned
AddressFamilyNumbers textual-convention described in
IANA-ADDRESS-FAMILY-NUMBERS-MIB DEFINITIONS, available from
http://www.iana.org/assignments/ianaaddressfamilynumbers-mib.
The enumerations are also listed in [IANA]. Note that this
list of address family numbers is maintained by IANA.
2. Length of LISP address: A field of length 1 octet, whose
value indicates the octet-length of the next (third)
field of this LispAddressType four-tuple.
3. LISP address: A field of variable length as indicated in
the previous (second) field, whose value is an address
of the IANA Address Family indicated in the first field
of this LispAddressType four-tuple. Note that any of
the IANA Address Families can be represented.
Particularly when the address family is LISP Canonical
Address Format (LCAF)
with IANA-assigned Address Family Number 16387, then the
first octet of this field indicates the LCAF type, and the
rest of this field is same as the encoding format of the
LISP Canonical Address after the length field, as defined
in LCAF document.
4. Mask-length of address: A field of length 1 octet, whose
value is the mask-length to be applied to the LISP
address specified in the previous (third) field.
To illustrate the use of this object, consider the LISP MIB
Object below titled lispMapCacheEntry. This object begins
with the following entities:
lispMapCacheEntry ::= SEQUENCE {
lispMapCacheEidLength INTEGER,
lispMapCacheEid LispAddressType,
... [skip] ...
Schudel, et al. Experimental [Page 8]
RFC 7052 LISP MIB October 2013
Example 1: Suppose that the IPv4 EID-Prefix stored is
192.0.2.0/24. In this case, the values within
lispMapCacheEntry would be:
lispMapCacheEidLength = 8
lispMapCacheEid = 1, 4, 192.0.2.0, 24
... [skip] ...
where 8 is the total length in octets of the next object
(lispMapCacheEID of type LispAddressType). Then, the value
1 indicates the IPv4 AF (per the
IANA-ADDRESS-FAMILY-NUMBERS-MIB), the value 4 indicates that
the AF is 4 octets in length, 192.0.2.0 is the IPv4 address,
and the value 24 is the mask-length in bits. Note that the
lispMapCacheEidLength value of 8 is used to compute the
length of the fourth (last) field in lispMapCacheEid to be 1
octet -- as computed by 8 - (2 + 1 + 4) = 1.
Example 2: Suppose that the IPv6 EID-Prefix stored is
2001:db8:a::/48. In this case, the values within
lispMapCacheEntry would be:
lispMapCacheEidLength = 20
lispMapCacheEid = 2, 16, 2001:db8:a::, 48
... [skip] ...
where 20 is the total length in octets of the next object
(lispMapCacheEID of type LispAddressType). Then, the value
2 indicates the IPv6 AF (per the
IANA-ADDRESS-FAMILY-NUMBERS-MIB), the value 16 indicates
that the AF is 16 octets in length, 2001:db8:a:: is the IPv6
address, and the value 48 is the mask-length in bits. Note
that the lispMapCacheEidLength value of 20 is used to
compute the length of the fourth (last) field in
lispMapCacheEid to be 1 octet -- as computed by
20 - (2 + 1 + 16) = 1.
Example 3: As an example where LCAF is used, suppose
that the IPv4 EID-Prefix stored is 192.0.2.0/24 and it
is part of LISP Instance ID 101. In this case, the values
within lispMapCacheEntry would be:
lispMapCacheEidLength = 11
lispMapCacheEid = 16387, 7, 2, 101, 1, 192.0.2.0, 24
... [skip] ...
Schudel, et al. Experimental [Page 9]
RFC 7052 LISP MIB October 2013
where 11 is the total length in octets of the next object
(lispMapCacheEID of type LispAddressType). Then, the value
16387 indicates the LCAF AF (see the
IANA-ADDRESS-FAMILY-NUMBERS-MIB), the value 7 indicates that
the LCAF AF is 7 octets in length in this case, 2 indicates
that LCAF Type 2 encoding is used (see the LCAF document), 101
gives the Instance ID, 1 gives the AFI (per the
IANA-ADDRESS-FAMILY-NUMBERS-MIB) for an IPv4 address, 192.0.2.0
is the IPv4 address, and 24 is the mask-length in bits. Note
that the lispMapCacheEidLength value of 11 octets is used to
compute the length of the last field in lispMapCacheEid to be 1
octet -- as computed by 11 - (2 + 1 + 1 + 1 + 1 + 4) = 1.
Note: all LISP header formats and locations of specific
flags, bits, and fields are as given in the base LISP
references of RFC 6830, RFC 6832, and RFC 6833."
REFERENCE
"RFC 6830, Section 14.2 and
LISP Canonical Address Format (LCAF), Work in Progress,
March 2013."
SYNTAX OCTET STRING (SIZE (5..39))
--
-- Top-level components of this MIB.
--
lispObjects OBJECT IDENTIFIER ::= { lispMIB 1 }
lispConformance OBJECT IDENTIFIER ::= { lispMIB 2 }
lispFeaturesTable OBJECT-TYPE
SYNTAX SEQUENCE OF LispFeaturesEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table represents the ON/OFF status of the
various LISP features that can be enabled on LISP devices."
REFERENCE
"RFC 6830, Section 4, Section 5.5., Section 6.3."
::= { lispObjects 1 }
Schudel, et al. Experimental [Page 10]
RFC 7052 LISP MIB October 2013
lispFeaturesEntry OBJECT-TYPE
SYNTAX LispFeaturesEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the lispFeaturesTable."
INDEX { lispFeaturesInstanceID,
lispFeaturesAddressFamily }
::= { lispFeaturesTable 1 }
LispFeaturesEntry ::= SEQUENCE {
lispFeaturesInstanceID Unsigned32,
lispFeaturesAddressFamily AddressFamilyNumbers,
lispFeaturesItrEnabled TruthValue,
lispFeaturesEtrEnabled TruthValue,
lispFeaturesProxyItrEnabled TruthValue,
lispFeaturesProxyEtrEnabled TruthValue,
lispFeaturesMapServerEnabled TruthValue,
lispFeaturesMapResolverEnabled TruthValue,
lispFeaturesMapCacheSize Unsigned32,
lispFeaturesMapCacheLimit Unsigned32,
lispFeaturesEtrMapCacheTtl Unsigned32,
lispFeaturesRlocProbeEnabled TruthValue,
lispFeaturesEtrAcceptMapDataEnabled TruthValue,
lispFeaturesEtrAcceptMapDataVerifyEnabled TruthValue,
lispFeaturesRouterTimeStamp TimeStamp
}
lispFeaturesInstanceID OBJECT-TYPE
SYNTAX Unsigned32 (0..16777215)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This represents the Instance ID of the LISP header.
An Instance ID in the LISP address encoding helps
uniquely identify the AFI-based address space to which
a given EID belongs. Its default value is 0."
DEFVAL { 0 }
::= { lispFeaturesEntry 1 }
lispFeaturesAddressFamily OBJECT-TYPE
SYNTAX AddressFamilyNumbers
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The IANA Address Family Number of destination address
of packets that this LISP device is enabled to process."
::= { lispFeaturesEntry 2 }
Schudel, et al. Experimental [Page 11]
RFC 7052 LISP MIB October 2013
lispFeaturesItrEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the status of ITR role on this device. If
this object is true, then the ITR feature is enabled."
::= { lispFeaturesEntry 3 }
lispFeaturesEtrEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the status of ETR role on this device. If
this object is true, then the ETR feature is enabled."
::= { lispFeaturesEntry 4 }
lispFeaturesProxyItrEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the status of Proxy-ITR role on this device.
If this object is true, then the Proxy-ITR feature is
enabled."
::= { lispFeaturesEntry 5 }
lispFeaturesProxyEtrEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the status of Proxy-ETR role on this device.
If this object is true, then the Proxy-ETR feature is
enabled."
::= { lispFeaturesEntry 6 }
lispFeaturesMapServerEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the status of Map Server role on this device.
If this object is true, then the Map-Server feature is
enabled."
::= { lispFeaturesEntry 7 }
Schudel, et al. Experimental [Page 12]
RFC 7052 LISP MIB October 2013
lispFeaturesMapResolverEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the status of Map Resolver role on this device.
If this object is true, then Map-Resolver feature is
enabled."
::= { lispFeaturesEntry 8 }
lispFeaturesMapCacheSize OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Size of EID-to-RLOC map-cache on this device."
::= { lispFeaturesEntry 9 }
lispFeaturesMapCacheLimit OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Maximum permissible entries in EID-to-RLOC map-cache on
this device."
::= { lispFeaturesEntry 10 }
lispFeaturesEtrMapCacheTtl OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The stored Record TTL of the EID-to-RLOC map record in
the map-cache."
::= { lispFeaturesEntry 11 }
lispFeaturesRlocProbeEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the status of RLOC-Probing feature on this
device. If this object is true, then this feature is
enabled."
::= { lispFeaturesEntry 12 }
Schudel, et al. Experimental [Page 13]
RFC 7052 LISP MIB October 2013
lispFeaturesEtrAcceptMapDataEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the status of accepting piggybacked mapping
data received in a map-request on this device. If this
object is true, then this device accepts piggybacked
mapping data."
::= { lispFeaturesEntry 13 }
lispFeaturesEtrAcceptMapDataVerifyEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the status of verifying accepted piggybacked
mapping data received in a map-request on this device.
If this object is true, then this device verifies
accepted piggybacked mapping data."
::= { lispFeaturesEntry 14 }
lispFeaturesRouterTimeStamp OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime at which the LISP feature was
enabled on this device.
If this information was present at the most recent
reinitialization of the local management subsystem,
then this object contains a zero value."
DEFVAL { 0 }
::= { lispFeaturesEntry 15 }
lispIidToVrfTable OBJECT-TYPE
SYNTAX SEQUENCE OF LispIidToVrfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table represents the mapping of a LISP Instance ID
to a VRF."
REFERENCE
"RFC 6830, Section 5.5., and RFC 4382, Section 7."
::= { lispObjects 2 }
Schudel, et al. Experimental [Page 14]
RFC 7052 LISP MIB October 2013
lispIidToVrfEntry OBJECT-TYPE
SYNTAX LispIidToVrfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the lispIidToVrfTable."
INDEX { lispFeaturesInstanceID }
::= { lispIidToVrfTable 1 }
LispIidToVrfEntry ::= SEQUENCE {
lispIidToVrfName MplsL3VpnName
}
lispIidToVrfName OBJECT-TYPE
SYNTAX MplsL3VpnName
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The identifier for each VPN that is mapped to the
given LISP Instance ID."
::= { lispIidToVrfEntry 1 }
lispGlobalStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF LispGlobalStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides global statistics for a given
Instance ID per address family on a LISP device."
REFERENCE
"RFC 6830, Section 6.1."
::= { lispObjects 3 }
lispGlobalStatsEntry OBJECT-TYPE
SYNTAX LispGlobalStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the
lispGlobalStatsTable."
INDEX { lispFeaturesInstanceID,
lispFeaturesAddressFamily }
::= { lispGlobalStatsTable 1 }
Schudel, et al. Experimental [Page 15]
RFC 7052 LISP MIB October 2013
LispGlobalStatsEntry ::= SEQUENCE {
lispGlobalStatsMapRequestsIn Counter64,
lispGlobalStatsMapRequestsOut Counter64,
lispGlobalStatsMapRepliesIn Counter64,
lispGlobalStatsMapRepliesOut Counter64,
lispGlobalStatsMapRegistersIn Counter64,
lispGlobalStatsMapRegistersOut Counter64
}
lispGlobalStatsMapRequestsIn OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of map requests received by this device for
any EID-Prefix of the given address family and Instance ID.
Discontinuities in this monotonically increasing value occur
at reinitialization of the management system.
Discontinuities can also occur as a result of LISP features
being removed, which can be detected by observing the value
of lispFeaturesRouterTimeStamp."
::= { lispGlobalStatsEntry 1 }
lispGlobalStatsMapRequestsOut OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of map requests sent by this device for any
EID-Prefix of the given address family and Instance ID.
Discontinuities in this monotonically increasing value occur
at reinitialization of the management system.
Discontinuities can also occur as a result of LISP features
being removed, which can be detected by observing the value
of lispFeaturesRouterTimeStamp."
::= { lispGlobalStatsEntry 2 }
lispGlobalStatsMapRepliesIn OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of map replies received by this device for any
EID-Prefix of the given address family and Instance ID.
Schudel, et al. Experimental [Page 16]
RFC 7052 LISP MIB October 2013
Discontinuities in this monotonically increasing value occur
at reinitialization of the management system.
Discontinuities can also occur as a result of LISP features
being removed, which can be detected by observing the value
of lispFeaturesRouterTimeStamp."
::= { lispGlobalStatsEntry 3 }
lispGlobalStatsMapRepliesOut OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of map replies sent by this device for any EID
prefix of the given address family and Instance ID.
Discontinuities in this monotonically increasing value occur
at reinitialization of the management system.
Discontinuities can also occur as a result of LISP features
being removed, which can be detected by observing the value
of lispFeaturesRouterTimeStamp."
::= { lispGlobalStatsEntry 4 }
lispGlobalStatsMapRegistersIn OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of map registers received by this device for
any EID-Prefix of the given address family and Instance ID.
Discontinuities in this monotonically increasing value occur
at reinitialization of the management system.
Discontinuities can also occur as a result of LISP features
being removed, which can be detected by observing the value
of lispFeaturesRouterTimeStamp."
::= { lispGlobalStatsEntry 5 }
lispGlobalStatsMapRegistersOut OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of map registers sent by this device for any
EID-Prefix of the given address family and Instance ID.
Discontinuities in this monotonically increasing value occur
at reinitialization of the management system.
Discontinuities can also occur as a result of LISP features
Schudel, et al. Experimental [Page 17]
RFC 7052 LISP MIB October 2013
being removed, which can be detected by observing the value
of lispFeaturesRouterTimeStamp."
::= { lispGlobalStatsEntry 6 }
lispMappingDatabaseTable OBJECT-TYPE
SYNTAX SEQUENCE OF LispMappingDatabaseEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table represents the EID-to-RLOC mapping database
that contains the EID-Prefix to RLOC mappings configured
on an ETR.
This table represents all such mappings for the given LISP
site to which this device belongs."
REFERENCE
"RFC 6830, Section 6."
::= { lispObjects 4 }
lispMappingDatabaseEntry OBJECT-TYPE
SYNTAX LispMappingDatabaseEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in lispMappingDatabaseTable."
INDEX { lispMappingDatabaseEidLength,
lispMappingDatabaseEid }
::= { lispMappingDatabaseTable 1 }
LispMappingDatabaseEntry ::= SEQUENCE {
lispMappingDatabaseEidLength Integer32,
lispMappingDatabaseEid LispAddressType,
lispMappingDatabaseLsb Unsigned32,
lispMappingDatabaseEidPartitioned TruthValue,
lispMappingDatabaseTimeStamp TimeStamp,
lispMappingDatabaseDecapOctets Counter64,
lispMappingDatabaseDecapPackets Counter64,
lispMappingDatabaseEncapOctets Counter64,
lispMappingDatabaseEncapPackets Counter64
}
Schudel, et al. Experimental [Page 18]
RFC 7052 LISP MIB October 2013
lispMappingDatabaseEidLength OBJECT-TYPE
SYNTAX Integer32 (5..39)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object gives the octet-length of
lispMappingDatabaseEid."
::= { lispMappingDatabaseEntry 1 }
lispMappingDatabaseEid OBJECT-TYPE
SYNTAX LispAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The EID-Prefix of the mapping database."
::= { lispMappingDatabaseEntry 2 }
lispMappingDatabaseLsb OBJECT-TYPE
SYNTAX Unsigned32 (0..4294967295)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The locator status bits for this EID-Prefix."
::= { lispMappingDatabaseEntry 3 }
lispMappingDatabaseEidPartitioned OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates if this device is partitioned from the site that
contains this EID-Prefix. If this object is true, then it
means this device is partitioned from the site."
::= { lispMappingDatabaseEntry 4 }
lispMappingDatabaseTimeStamp OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime at which the EID Prefix information
represented by this mapping database entry was configured
on this device.
Schudel, et al. Experimental [Page 19]
RFC 7052 LISP MIB October 2013
If this information was present at the most recent
reinitialization of the local management subsystem, then
this object contains a zero value."
DEFVAL { 0 }
::= { lispMappingDatabaseEntry 5 }
lispMappingDatabaseDecapOctets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of octets, after decapsulation, of LISP packets
that were decapsulated by this device addressed to a host
within this EID-Prefix.
Discontinuities in this monotonically increasing value occur
at reinitialization of the management system.
Discontinuities can also occur as a result of LISP features
being removed, which can be detected by observing the value
of lispMappingDatabaseTimeStamp."
::= { lispMappingDatabaseEntry 6 }
lispMappingDatabaseDecapPackets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of LISP packets that were decapsulated by this
device addressed to a host within this EID-Prefix.
Discontinuities in this monotonically increasing value occur
at reinitialization of the management system.
Discontinuities can also occur as a result of LISP features
being removed, which can be detected by observing the value
of lispMappingDatabaseTimeStamp."
::= { lispMappingDatabaseEntry 7 }
lispMappingDatabaseEncapOctets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of octets, before encapsulation, of LISP packets
that were encapsulated by this device, whose inner header
source address matched this EID-Prefix.
Schudel, et al. Experimental [Page 20]
RFC 7052 LISP MIB October 2013
Discontinuities in this monotonically increasing value occur
at reinitialization of the management system.
Discontinuities can also occur as a result of LISP features
being removed, which can be detected by observing the value
of lispMappingDatabaseTimeStamp."
::= { lispMappingDatabaseEntry 8 }
lispMappingDatabaseEncapPackets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of LISP packets that were encapsulated by this
device whose inner header source address matched this EID
prefix.
Discontinuities in this monotonically increasing value occur
at reinitialization of the management system.
Discontinuities can also occur as a result of LISP features
being removed, which can be detected by observing the value
of lispMappingDatabaseTimeStamp."
::= { lispMappingDatabaseEntry 9 }
lispMappingDatabaseLocatorTable OBJECT-TYPE
SYNTAX SEQUENCE OF LispMappingDatabaseLocatorEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table represents the set of routing locators per EID
prefix contained in the EID-to-RLOC database configured on
this ETR."
REFERENCE
"RFC 6830, Section 6.2."
::= { lispObjects 5 }
lispMappingDatabaseLocatorEntry OBJECT-TYPE
SYNTAX LispMappingDatabaseLocatorEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the
lispMappingDatabaseLocatorTable."
INDEX { lispMappingDatabaseEidLength,
lispMappingDatabaseEid,
lispMappingDatabaseLocatorRlocLength,
lispMappingDatabaseLocatorRloc }
::= { lispMappingDatabaseLocatorTable 1 }
Schudel, et al. Experimental [Page 21]
RFC 7052 LISP MIB October 2013
LispMappingDatabaseLocatorEntry ::= SEQUENCE {
lispMappingDatabaseLocatorRlocLength Integer32,
lispMappingDatabaseLocatorRloc LispAddressType,
lispMappingDatabaseLocatorRlocPriority Integer32,
lispMappingDatabaseLocatorRlocWeight Integer32,
lispMappingDatabaseLocatorRlocMPriority Integer32,
lispMappingDatabaseLocatorRlocMWeight Integer32,
lispMappingDatabaseLocatorRlocState INTEGER,
lispMappingDatabaseLocatorRlocLocal INTEGER,
lispMappingDatabaseLocatorRlocTimeStamp TimeStamp,
lispMappingDatabaseLocatorRlocDecapOctets Counter64,
lispMappingDatabaseLocatorRlocDecapPackets Counter64,
lispMappingDatabaseLocatorRlocEncapOctets Counter64,
lispMappingDatabaseLocatorRlocEncapPackets Counter64
}
lispMappingDatabaseLocatorRlocLength OBJECT-TYPE
SYNTAX Integer32 (5..39)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object is used to get the octet-length of
lispMappingDatabaseLocatorRloc."
::= { lispMappingDatabaseLocatorEntry 1 }
lispMappingDatabaseLocatorRloc OBJECT-TYPE
SYNTAX LispAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object is a locator for the given EID-Prefix in
the mapping database."
::= { lispMappingDatabaseLocatorEntry 2 }
lispMappingDatabaseLocatorRlocPriority OBJECT-TYPE
SYNTAX Integer32 (0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The unicast priority of the RLOC."
::= { lispMappingDatabaseLocatorEntry 3 }
lispMappingDatabaseLocatorRlocWeight OBJECT-TYPE
SYNTAX Integer32 (0..100)
MAX-ACCESS read-only
STATUS current
Schudel, et al. Experimental [Page 22]
RFC 7052 LISP MIB October 2013
DESCRIPTION
"The unicast weight of the RLOC."
::= { lispMappingDatabaseLocatorEntry 4 }
lispMappingDatabaseLocatorRlocMPriority OBJECT-TYPE
SYNTAX Integer32 (0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The multicast priority of the RLOC."
::= { lispMappingDatabaseLocatorEntry 5 }
lispMappingDatabaseLocatorRlocMWeight OBJECT-TYPE
SYNTAX Integer32 (0..100)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The multicast weight of the RLOC."
::= { lispMappingDatabaseLocatorEntry 6 }
lispMappingDatabaseLocatorRlocState OBJECT-TYPE
SYNTAX INTEGER {
up (1),
down (2),
unreachable (3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The state of this RLOC as per this device.
(1 = RLOC is up; 2 = RLOC is down; 3 = RLOC is unreachable)."
::= { lispMappingDatabaseLocatorEntry 7 }
lispMappingDatabaseLocatorRlocLocal OBJECT-TYPE
SYNTAX INTEGER {
siteself (1),
sitelocal (2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates whether the RLOC is local to this device
(or remote, meaning local to another device in the same LISP
site). (1 = RLOC is an address on this device; 2 = RLOC is
an address on another device)."
::= { lispMappingDatabaseLocatorEntry 8 }
Schudel, et al. Experimental [Page 23]
RFC 7052 LISP MIB October 2013
lispMappingDatabaseLocatorRlocTimeStamp OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime at which the RLOC of the EID Prefix
represented by this mapping database entry was configured
on this device.
If this information was present at the most recent
reinitialization of the local management subsystem, then
this object contains a zero value."
DEFVAL { 0 }
::= { lispMappingDatabaseLocatorEntry 9 }
lispMappingDatabaseLocatorRlocDecapOctets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of octets of LISP packets that were
addressed to this RLOC of the EID-Prefix and
were decapsulated.
Discontinuities in this monotonically increasing value occur
at reinitialization of the management system.
Discontinuities can also occur as a result of database
mappings getting reconfigured or RLOC status changes, which
can be detected by observing the value of
lispMappingDatabaseLocatorRlocTimeStamp."
::= { lispMappingDatabaseLocatorEntry 10 }
lispMappingDatabaseLocatorRlocDecapPackets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of LISP packets that were addressed to this RLOC
of the EID-Prefix and were decapsulated.
Discontinuities in this monotonically increasing value occur
at reinitialization of the management system.
Discontinuities can also occur as a result of database
mappings getting reconfigured or RLOC status changes, which
can be detected by observing the value of
lispMappingDatabaseLocatorRlocTimeStamp."
::= { lispMappingDatabaseLocatorEntry 11 }
Schudel, et al. Experimental [Page 24]
RFC 7052 LISP MIB October 2013
lispMappingDatabaseLocatorRlocEncapOctets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of octets of LISP packets that were encapsulated
by this device using this RLOC address as the source, and
that were sourced by an address of this EID-Prefix.
Discontinuities in this monotonically increasing value occur
at reinitialization of the management system.
Discontinuities can also occur as a result of database
mappings getting reconfigured or RLOC status changes, which
can be detected by observing the value of
lispMappingDatabaseLocatorRlocTimeStamp."
::= { lispMappingDatabaseLocatorEntry 12 }
lispMappingDatabaseLocatorRlocEncapPackets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of LISP packets that were encapsulated by this
device using this RLOC address as the source and that were
sourced by an address of this EID-Prefix.
Discontinuities in this monotonically increasing value occur
at reinitialization of the management system.
Discontinuities can also occur as a result of database
mappings getting reconfigured or RLOC status changes, which
can be detected by observing the value of
lispMappingDatabaseLocatorRlocTimeStamp."
::= { lispMappingDatabaseLocatorEntry 13 }
lispMapCacheTable OBJECT-TYPE
SYNTAX SEQUENCE OF LispMapCacheEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table represents the short-lived, on-demand table on
an ITR that stores, tracks, and is responsible for
timing-out and otherwise validating EID-to-RLOC mappings."
REFERENCE
"RFC 6830, Sections 6 and Section 12."
::= { lispObjects 6 }
Schudel, et al. Experimental [Page 25]
RFC 7052 LISP MIB October 2013
lispMapCacheEntry OBJECT-TYPE
SYNTAX LispMapCacheEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the
lispMapCacheTable."
INDEX { lispMapCacheEidLength,
lispMapCacheEid }
::= { lispMapCacheTable 1 }
LispMapCacheEntry ::= SEQUENCE {
lispMapCacheEidLength Integer32,
lispMapCacheEid LispAddressType,
lispMapCacheEidTimeStamp TimeStamp,
lispMapCacheEidExpiryTime TimeTicks,
lispMapCacheEidState TruthValue,
lispMapCacheEidAuthoritative TruthValue,
lispMapCacheEidDecapOctets Counter64,
lispMapCacheEidDecapPackets Counter64,
lispMapCacheEidEncapOctets Counter64,
lispMapCacheEidEncapPackets Counter64
}
lispMapCacheEidLength OBJECT-TYPE
SYNTAX Integer32 (5..39)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object is used to get the octet-length of
lispMapCacheEid."
::= { lispMapCacheEntry 1 }
lispMapCacheEid OBJECT-TYPE
SYNTAX LispAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The EID-Prefix in the mapping cache."
::= { lispMapCacheEntry 2 }
lispMapCacheEidTimeStamp OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime at which the EID Prefix information
represented by this entry was learned by this device.
Schudel, et al. Experimental [Page 26]
RFC 7052 LISP MIB October 2013
If this information was present at the most recent
reinitialization of the local management subsystem, then
this object contains a zero value."
DEFVAL { 0 }
::= { lispMapCacheEntry 3 }
lispMapCacheEidExpiryTime OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time remaining before the ITR times-out this
EID-Prefix."
::= { lispMapCacheEntry 4 }
lispMapCacheEidState OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object is used to indicate the activity of this EID
prefix. If this object is true, then it means this EID
prefix is seeing activity."
::= { lispMapCacheEntry 5 }
lispMapCacheEidAuthoritative OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object is used to indicate whether the EID-Prefix was
installed by an authoritative map-reply. If this object is
true, then it means this EID-Prefix was installed by an
authoritative map-reply."
::= { lispMapCacheEntry 6 }
lispMapCacheEidDecapOctets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of octets of LISP packets that were decapsulated
by this device and were sourced from a remote host within
this EID-Prefix.
Discontinuities in this monotonically increasing value occur
at reinitialization of the management system.
Discontinuities can also occur as a result of cache being
Schudel, et al. Experimental [Page 27]
RFC 7052 LISP MIB October 2013
removed and replaced, which can be detected by observing the
value of lispMapCacheEidTimeStamp."
::= { lispMapCacheEntry 7 }
lispMapCacheEidDecapPackets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of LISP packets that were decapsulated by this
device and were sourced from a remote host within this
EID-Prefix.
Discontinuities in this monotonically increasing value occur
at reinitialization of the management system.
Discontinuities can also occur as a result of cache being
removed and replaced, which can be detected by observing the
value of lispMapCacheEidTimeStamp."
::= { lispMapCacheEntry 8 }
lispMapCacheEidEncapOctets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of octets of LISP packets that were encapsulated
by this device using the given EID-Prefix in the map-cache.
Discontinuities in this monotonically increasing value occur
at reinitialization of the management system.
Discontinuities can also occur as a result of cache being
removed and replaced, which can be detected by observing the
value of lispMapCacheEidTimeStamp."
::= { lispMapCacheEntry 9 }
lispMapCacheEidEncapPackets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of LISP packets that were encapsulated by this
device using the given EID-Prefix in the map-cache.
Schudel, et al. Experimental [Page 28]
RFC 7052 LISP MIB October 2013
Discontinuities in this monotonically increasing value occur
at reinitialization of the management system.
Discontinuities can also occur as a result of cache being
removed and replaced, which can be detected by observing the
value of lispMapCacheEidTimeStamp."
::= { lispMapCacheEntry 10 }
lispMapCacheLocatorTable OBJECT-TYPE
SYNTAX SEQUENCE OF LispMapCacheLocatorEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table represents the set of locators per EID-Prefix
contained in the map-cache table of an ITR."
REFERENCE
"RFC 6830, Section 6.3."
::= { lispObjects 7 }
lispMapCacheLocatorEntry OBJECT-TYPE
SYNTAX LispMapCacheLocatorEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the
lispMapCacheLocatorTable."
INDEX { lispMapCacheEidLength,
lispMapCacheEid,
lispMapCacheLocatorRlocLength,
lispMapCacheLocatorRloc }
::= { lispMapCacheLocatorTable 1 }
LispMapCacheLocatorEntry ::= SEQUENCE {
lispMapCacheLocatorRlocLength Integer32,
lispMapCacheLocatorRloc LispAddressType,
lispMapCacheLocatorRlocPriority Integer32,
lispMapCacheLocatorRlocWeight Integer32,
lispMapCacheLocatorRlocMPriority Integer32,
lispMapCacheLocatorRlocMWeight Integer32,
lispMapCacheLocatorRlocState INTEGER,
lispMapCacheLocatorRlocTimeStamp TimeStamp,
lispMapCacheLocatorRlocLastPriorityChange TimeTicks,
lispMapCacheLocatorRlocLastWeightChange TimeTicks,
lispMapCacheLocatorRlocLastMPriorityChange TimeTicks,
lispMapCacheLocatorRlocLastMWeightChange TimeTicks,
lispMapCacheLocatorRlocLastStateChange TimeTicks,
lispMapCacheLocatorRlocRtt TimeTicks,
lispMapCacheLocatorRlocDecapOctets Counter64,
lispMapCacheLocatorRlocDecapPackets Counter64,
Schudel, et al. Experimental [Page 29]
RFC 7052 LISP MIB October 2013
lispMapCacheLocatorRlocEncapOctets Counter64,
lispMapCacheLocatorRlocEncapPackets Counter64
}
lispMapCacheLocatorRlocLength OBJECT-TYPE
SYNTAX Integer32 (5..39)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object is used to get the octet-length of
lispMapCacheLocatorRloc."
::= { lispMapCacheLocatorEntry 1 }
lispMapCacheLocatorRloc OBJECT-TYPE
SYNTAX LispAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The locator for the EID-Prefix in the mapping cache."
::= { lispMapCacheLocatorEntry 2 }
lispMapCacheLocatorRlocPriority OBJECT-TYPE
SYNTAX Integer32 (0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The unicast priority of the RLOC for this EID-Prefix
(0-255); lower is more preferred."
::= { lispMapCacheLocatorEntry 3 }
lispMapCacheLocatorRlocWeight OBJECT-TYPE
SYNTAX Integer32 (0..100)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The unicast weight of the RLOC for this EID-Prefix
(0 - 100) percentage."
::= { lispMapCacheLocatorEntry 4 }
lispMapCacheLocatorRlocMPriority OBJECT-TYPE
SYNTAX Integer32 (0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The multicast priority of the RLOC for this EID-Prefix
(0-255); lower is more preferred."
::= { lispMapCacheLocatorEntry 5 }
Schudel, et al. Experimental [Page 30]
RFC 7052 LISP MIB October 2013
lispMapCacheLocatorRlocMWeight OBJECT-TYPE
SYNTAX Integer32 (0..100)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The multicast weight of the RLOC for this EID-Prefix
(0 - 100) percentage."
::= { lispMapCacheLocatorEntry 6 }
lispMapCacheLocatorRlocState OBJECT-TYPE
SYNTAX INTEGER {
up (1),
down (2),
unreachable (3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The state of this RLOC as per this device
(1 = RLOC is up; 2 = RLOC is down; 3 = RLOC is unreachable)."
::= { lispMapCacheLocatorEntry 7 }
lispMapCacheLocatorRlocTimeStamp OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime at which the RLOC of EID-Prefix
information represented by this entry was learned by
this device.
If this information was present at the most recent
reinitialization of the local management subsystem,
then this object contains a zero value."
DEFVAL { 0 }
::= { lispMapCacheLocatorEntry 8 }
lispMapCacheLocatorRlocLastPriorityChange OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Time elapsed since the last change of the unicast priority
of the RLOC for this EID-Prefix. Note that this is
independent of lispMapCacheLocatorRlocTimeStamp."
::= { lispMapCacheLocatorEntry 9 }
Schudel, et al. Experimental [Page 31]
RFC 7052 LISP MIB October 2013
lispMapCacheLocatorRlocLastWeightChange OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Time elapsed since the last change of the unicast weight
of the RLOC for this EID-Prefix. Note that this is
independent of lispMapCacheLocatorRlocTimeStamp."
::= { lispMapCacheLocatorEntry 10 }
lispMapCacheLocatorRlocLastMPriorityChange OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Time since the last change of the multicast priority of the
RLOC for this EID-Prefix."
::= { lispMapCacheLocatorEntry 11 }
lispMapCacheLocatorRlocLastMWeightChange OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Time since the last change of the multicast weight of the
RLOC for this EID-Prefix."
::= { lispMapCacheLocatorEntry 12 }
lispMapCacheLocatorRlocLastStateChange OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Time since the last change of the up/down state of the
RLOC for this EID-Prefix."
::= { lispMapCacheLocatorEntry 13 }
lispMapCacheLocatorRlocRtt OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Round-trip time of RLOC probe and map-reply for this RLOC
address for this prefix."
::= { lispMapCacheLocatorEntry 14 }
Schudel, et al. Experimental [Page 32]
RFC 7052 LISP MIB October 2013
lispMapCacheLocatorRlocDecapOctets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of octets of LISP packets that were decapsulated
by this device and were sourced from a remote host within
this EID-Prefix and were encapsulated for this RLOC.
Discontinuities in this monotonically increasing value occur
at reinitialization of the management system.
Discontinuities can also occur as a result of RLOC of cache
being removed and replaced, which can be detected by
observing the value of lispMapCacheLocatorRlocTimeStamp."
::= { lispMapCacheLocatorEntry 15 }
lispMapCacheLocatorRlocDecapPackets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of LISP packets that were decapsulated by this
device and were sourced from a remote host within this
EID-Prefix and were encapsulated for this RLOC.
Discontinuities in this monotonically increasing value occur
at reinitialization of the management system.
Discontinuities can also occur as a result of RLOC of cache
being removed and replaced, which can be detected by
observing the value of lispMapCacheLocatorRlocTimeStamp."
::= { lispMapCacheLocatorEntry 16 }
lispMapCacheLocatorRlocEncapOctets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of octets of LISP packets that matched this
EID-Prefix and were encapsulated using this RLOC address.
Discontinuities in this monotonically increasing value occur
at reinitialization of the management system.
Discontinuities can also occur as a result of RLOC of cache
being removed and replaced, which can be detected by
observing the value of lispMapCacheLocatorRlocTimeStamp."
::= { lispMapCacheLocatorEntry 17 }
Schudel, et al. Experimental [Page 33]
RFC 7052 LISP MIB October 2013
lispMapCacheLocatorRlocEncapPackets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of LISP packets that matched this EID-Prefix
and were encapsulated using this RLOC address.
Discontinuities in this monotonically increasing value occur
at reinitialization of the management system.
Discontinuities can also occur as a result of RLOC of cache
being removed and replaced, which can be detected by
observing the value of lispMapCacheLocatorRlocTimeStamp."
::= { lispMapCacheLocatorEntry 18 }
lispConfiguredLocatorTable OBJECT-TYPE
SYNTAX SEQUENCE OF LispConfiguredLocatorEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table represents the set of routing locators
configured on this device. Note that the addresses
configured by Proxy-ITR are treated as routing locators
and therefore can be part of this table."
REFERENCE
"RFC 6830, Section 6.3."
::= { lispObjects 8 }
lispConfiguredLocatorEntry OBJECT-TYPE
SYNTAX LispConfiguredLocatorEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the
lispConfiguredLocatorTable."
INDEX { lispConfiguredLocatorRlocLength,
lispConfiguredLocatorRloc }
::= { lispConfiguredLocatorTable 1 }
LispConfiguredLocatorEntry ::= SEQUENCE {
lispConfiguredLocatorRlocLength Integer32,
lispConfiguredLocatorRloc LispAddressType,
lispConfiguredLocatorRlocState INTEGER,
lispConfiguredLocatorRlocLocal INTEGER,
lispConfiguredLocatorRlocTimeStamp TimeStamp,
lispConfiguredLocatorRlocDecapOctets Counter64,
lispConfiguredLocatorRlocDecapPackets Counter64,
lispConfiguredLocatorRlocEncapOctets Counter64,
Schudel, et al. Experimental [Page 34]
RFC 7052 LISP MIB October 2013
lispConfiguredLocatorRlocEncapPackets Counter64
}
lispConfiguredLocatorRlocLength OBJECT-TYPE
SYNTAX Integer32 (5..39)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object is used to get the octet-length of
lispConfiguredLocatorRloc."
::= { lispConfiguredLocatorEntry 1 }
lispConfiguredLocatorRloc OBJECT-TYPE
SYNTAX LispAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object is an RLOC address configured on this device.
It can be an RLOC that is local to this device or can be an
RLOC that belongs to another ETR within the same site.
Proxy-ITR address is treated as an RLOC."
::= { lispConfiguredLocatorEntry 2 }
lispConfiguredLocatorRlocState OBJECT-TYPE
SYNTAX INTEGER {
up (1),
down (2),
unreachable (3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The state of this RLOC as per this device. (1 = RLOC is up;
2 = RLOC is down; 3 = RLOC is unreachable)."
::= { lispConfiguredLocatorEntry 3 }
lispConfiguredLocatorRlocLocal OBJECT-TYPE
SYNTAX INTEGER {
siteself (1),
sitelocal (2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates whether the RLOC is local to this device (or
remote, meaning local to another device in the same LISP
site). (1 = RLOC is an address on this device; 2 = RLOC is
an address on another device)."
Schudel, et al. Experimental [Page 35]
RFC 7052 LISP MIB October 2013
::= { lispConfiguredLocatorEntry 4 }
lispConfiguredLocatorRlocTimeStamp OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime at which the RLOC was configured on
this device.
If this information was present at the most recent
reinitialization of the local management subsystem, then
this object contains a zero value."
DEFVAL { 0 }
::= { lispConfiguredLocatorEntry 5 }
lispConfiguredLocatorRlocDecapOctets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of octets of LISP packets that were addressed to
this RLOC and were decapsulated.
Discontinuities in this monotonically increasing value occur
at reinitialization of the management system.
Discontinuities can also occur as a result of configured
RLOC being removed and replaced, which can be detected by
observing the value of lispConfiguredLocatorRlocTimeStamp."
::= { lispConfiguredLocatorEntry 6 }
lispConfiguredLocatorRlocDecapPackets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of LISP packets that were addressed to this RLOC
and were decapsulated.
Discontinuities in this monotonically increasing value occur
at reinitialization of the management system.
Discontinuities can also occur as a result of configured
RLOC being removed and replaced, which can be detected by
observing the value of lispConfiguredLocatorRlocTimeStamp."
::= { lispConfiguredLocatorEntry 7 }
Schudel, et al. Experimental [Page 36]
RFC 7052 LISP MIB October 2013
lispConfiguredLocatorRlocEncapOctets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of octets of LISP packets that were encapsulated
by this device using this RLOC address as the source.
Discontinuities in this monotonically increasing value occur
at reinitialization of the management system.
Discontinuities can also occur as a result of configured
RLOC being removed and replaced, which can be detected by
observing the value of lispConfiguredLocatorRlocTimeStamp."
::= { lispConfiguredLocatorEntry 8 }
lispConfiguredLocatorRlocEncapPackets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of LISP packets that were encapsulated by this
device using this RLOC address as the source.
Discontinuities in this monotonically increasing value occur
at reinitialization of the management system.
Discontinuities can also occur as a result of configured
RLOC being removed and replaced, which can be detected by
observing the value of lispConfiguredLocatorRlocTimeStamp."
::= { lispConfiguredLocatorEntry 9 }
lispEidRegistrationTable OBJECT-TYPE
SYNTAX SEQUENCE OF LispEidRegistrationEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides the properties of each LISP EID-Prefix
that is registered with this device when configured to be
a Map-Server."
REFERENCE
"RFC 6833, Section 4."
::= { lispObjects 9 }
lispEidRegistrationEntry OBJECT-TYPE
SYNTAX LispEidRegistrationEntry
MAX-ACCESS not-accessible
STATUS current
Schudel, et al. Experimental [Page 37]
RFC 7052 LISP MIB October 2013
DESCRIPTION
"An entry (conceptual row) in the lispEidRegistrationTable."
INDEX { lispEidRegistrationEidLength,
lispEidRegistrationEid }
::= { lispEidRegistrationTable 1 }
LispEidRegistrationEntry ::= SEQUENCE {
lispEidRegistrationEidLength Integer32,
lispEidRegistrationEid LispAddressType,
lispEidRegistrationSiteName OCTET STRING,
lispEidRegistrationSiteDescription OCTET STRING,
lispEidRegistrationIsRegistered TruthValue,
lispEidRegistrationFirstTimeStamp TimeStamp,
lispEidRegistrationLastTimeStamp TimeStamp,
lispEidRegistrationLastRegisterSenderLength Integer32,
lispEidRegistrationLastRegisterSender LispAddressType,
lispEidRegistrationAuthenticationErrors Counter64,
lispEidRegistrationRlocsMismatch Counter64
}
lispEidRegistrationEidLength OBJECT-TYPE
SYNTAX Integer32 (5..39)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object is used to get the octet-length of
lispEidRegistrationEid."
::= { lispEidRegistrationEntry 1 }
lispEidRegistrationEid OBJECT-TYPE
SYNTAX LispAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The EID-Prefix that is being registered."
::= { lispEidRegistrationEntry 2 }
lispEidRegistrationSiteName OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(0..63))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Site name used by a Map-Server to distinguish different
LISP sites that are registering with it."
::= { lispEidRegistrationEntry 3 }
lispEidRegistrationSiteDescription OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(0..255))
Schudel, et al. Experimental [Page 38]
RFC 7052 LISP MIB October 2013
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Description for a site name used by a Map-Server. The EID
prefix that is being registered belongs to this site."
::= { lispEidRegistrationEntry 4 }
lispEidRegistrationIsRegistered OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the registration status of the given EID-Prefix.
If this object is true, then it means the EID-Prefix is
registered.
The value false implies the EID-Prefix is not registered
with the Map Server. There are multiple scenarios when this
could happen like authentication failures, routing problems,
misconfigs to name a few."
::= { lispEidRegistrationEntry 5 }
lispEidRegistrationFirstTimeStamp OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime at which the first valid register
message for the EID Prefix information represented by this
entry was received by this device.
If this information was present at the most recent
reinitialization of the local management subsystem, then
this object contains a zero value."
DEFVAL { 0 }
::= { lispEidRegistrationEntry 6 }
lispEidRegistrationLastTimeStamp OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime at which the last valid register
message for the EID Prefix information represented by this
entry was received by this device.
Schudel, et al. Experimental [Page 39]
RFC 7052 LISP MIB October 2013
If this information was present at the most recent
reinitialization of the local management subsystem, then
this object contains a zero value."
DEFVAL { 0 }
::= { lispEidRegistrationEntry 7 }
lispEidRegistrationLastRegisterSenderLength OBJECT-TYPE
SYNTAX Integer32 (5..39)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object is used to get the octet-length of
lispEidRegistrationLastRegisterSender, the next
object."
::= { lispEidRegistrationEntry 8 }
lispEidRegistrationLastRegisterSender OBJECT-TYPE
SYNTAX LispAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Source address of the last valid register message for the
given EID-Prefix that was received by this device."
::= { lispEidRegistrationEntry 9 }
lispEidRegistrationAuthenticationErrors OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of total authentication errors of map-registers
received for the given EID-Prefix.
Discontinuities in this monotonically increasing value occur
at reinitialization of the management system.
Discontinuities can also occur as a result of site config
changes, which can be detected by observing the value of
lispEidRegistrationFirstTimeStamp."
::= { lispEidRegistrationEntry 10 }
lispEidRegistrationRlocsMismatch OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of total map-registers received that had at least one
RLOC that was not in the allowed list of RLOCs for the given
EID-Prefix.
Schudel, et al. Experimental [Page 40]
RFC 7052 LISP MIB October 2013
Discontinuities in this monotonically increasing value occur
at reinitialization of the management system.
Discontinuities can also occur as a result of site config
changes, which can be detected by observing the value of
lispEidRegistrationFirstTimeStamp."
::= { lispEidRegistrationEntry 11 }
lispEidRegistrationEtrTable OBJECT-TYPE
SYNTAX SEQUENCE OF LispEidRegistrationEtrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides the properties of ETRs that register
the given EID-Prefix with this device when configured to
be a Map-Server."
REFERENCE
"RFC 6830, Section 6.1."
::= { lispObjects 10 }
lispEidRegistrationEtrEntry OBJECT-TYPE
SYNTAX LispEidRegistrationEtrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the
lispEidRegistrationEtrTable."
INDEX { lispEidRegistrationEidLength,
lispEidRegistrationEid,
lispEidRegistrationEtrSenderLength,
lispEidRegistrationEtrSender }
::= { lispEidRegistrationEtrTable 1 }
LispEidRegistrationEtrEntry ::= SEQUENCE {
lispEidRegistrationEtrSenderLength Integer32,
lispEidRegistrationEtrSender LispAddressType,
lispEidRegistrationEtrLastTimeStamp TimeStamp,
lispEidRegistrationEtrTtl Unsigned32,
lispEidRegistrationEtrProxyReply TruthValue,
lispEidRegistrationEtrWantsMapNotify TruthValue
}
lispEidRegistrationEtrSenderLength OBJECT-TYPE
SYNTAX Integer32 (5..39)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object is used to get the octet-length of
lispEidRegistrationEtrSender."
Schudel, et al. Experimental [Page 41]
RFC 7052 LISP MIB October 2013
::= { lispEidRegistrationEtrEntry 1 }
lispEidRegistrationEtrSender OBJECT-TYPE
SYNTAX LispAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Source address of the ETR that is sending valid register
messages for this EID-Prefix to this device."
::= { lispEidRegistrationEtrEntry 2 }
lispEidRegistrationEtrLastTimeStamp OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime at which the last valid register
message from this ETR for the EID Prefix information
represented by this entry was received by this device.
If this information was present at the most recent
reinitialization of the local management subsystem,
then this object contains a zero value."
DEFVAL { 0 }
::= { lispEidRegistrationEtrEntry 3 }
lispEidRegistrationEtrTtl OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Record TTL of the registering ETR device for this
EID-Prefix."
::= { lispEidRegistrationEtrEntry 4 }
lispEidRegistrationEtrProxyReply OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates proxy-replying status of the registering ETR for
this EID-Prefix. If this object is true, then it means the
Map-Server can proxy-reply."
::= { lispEidRegistrationEtrEntry 5 }
lispEidRegistrationEtrWantsMapNotify OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
Schudel, et al. Experimental [Page 42]
RFC 7052 LISP MIB October 2013
STATUS current
DESCRIPTION
"Indicates whether the EID-Prefix wants Map-Notifications.
If this object is true, then it means the EID-Prefix wants
Map-Notifications."
::= { lispEidRegistrationEtrEntry 6 }
lispEidRegistrationLocatorTable OBJECT-TYPE
SYNTAX SEQUENCE OF LispEidRegistrationLocatorEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides the properties of all locators per
LISP site that are served by this device when configured
to be a Map-Server."
REFERENCE
"RFC 6830, Section 6.1."
::= { lispObjects 11 }
lispEidRegistrationLocatorEntry OBJECT-TYPE
SYNTAX LispEidRegistrationLocatorEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the
lispEidRegistrationLocatorTable."
INDEX { lispEidRegistrationEidLength,
lispEidRegistrationEid,
lispEidRegistrationEtrSenderLength,
lispEidRegistrationEtrSender,
lispEidRegistrationLocatorRlocLength,
lispEidRegistrationLocatorRloc }
::= { lispEidRegistrationLocatorTable 1 }
LispEidRegistrationLocatorEntry ::= SEQUENCE {
lispEidRegistrationLocatorRlocLength Integer32,
lispEidRegistrationLocatorRloc LispAddressType,
lispEidRegistrationLocatorRlocState INTEGER,
lispEidRegistrationLocatorIsLocal TruthValue,
lispEidRegistrationLocatorPriority Integer32,
lispEidRegistrationLocatorWeight Integer32,
lispEidRegistrationLocatorMPriority Integer32,
lispEidRegistrationLocatorMWeight Integer32
}
lispEidRegistrationLocatorRlocLength OBJECT-TYPE
SYNTAX Integer32 (5..39)
MAX-ACCESS not-accessible
Schudel, et al. Experimental [Page 43]
RFC 7052 LISP MIB October 2013
STATUS current
DESCRIPTION
"This object is used to get the octet-length of
lispEidRegistrationLocatorRloc."
::= { lispEidRegistrationLocatorEntry 1 }
lispEidRegistrationLocatorRloc OBJECT-TYPE
SYNTAX LispAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The locator of the given EID-Prefix being registered by the
given ETR with this device."
::= { lispEidRegistrationLocatorEntry 2 }
lispEidRegistrationLocatorRlocState OBJECT-TYPE
SYNTAX INTEGER {
up (1),
down (2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The cached state of this RLOC received in map-register from
the ETR by the device, in the capacity of a Map-Server.
Value 1 refers to up, value 2 refers to down."
::= { lispEidRegistrationLocatorEntry 3 }
lispEidRegistrationLocatorIsLocal OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates if the given locator is local to the registering
ETR. If this object is true, it means the locator is
local."
::= { lispEidRegistrationLocatorEntry 4 }
lispEidRegistrationLocatorPriority OBJECT-TYPE
SYNTAX Integer32 (0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The unicast priority of the RLOC for this EID-Prefix in the
register message sent by the given ETR."
::= { lispEidRegistrationLocatorEntry 5 }
Schudel, et al. Experimental [Page 44]
RFC 7052 LISP MIB October 2013
lispEidRegistrationLocatorWeight OBJECT-TYPE
SYNTAX Integer32 (0..100)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The unicast weight of the RLOC for this EID-Prefix in the
register message sent by the given ETR."
::= { lispEidRegistrationLocatorEntry 6 }
lispEidRegistrationLocatorMPriority OBJECT-TYPE
SYNTAX Integer32 (0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The multicast priority of the RLOC for this EID-Prefix in
the register message sent by the given ETR."
::= { lispEidRegistrationLocatorEntry 7 }
lispEidRegistrationLocatorMWeight OBJECT-TYPE
SYNTAX Integer32 (0..100)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The multicast weight of the RLOC for this EID-Prefix in the
register message sent by the given ETR."
::= { lispEidRegistrationLocatorEntry 8 }
lispUseMapServerTable OBJECT-TYPE
SYNTAX SEQUENCE OF LispUseMapServerEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides the properties of the Map-Server(s)
with which this device is configured to register."
REFERENCE
"RFC 6833, Section 4.3."
::= { lispObjects 12 }
lispUseMapServerEntry OBJECT-TYPE
SYNTAX LispUseMapServerEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the lispUseMapServerTable."
INDEX { lispUseMapServerAddressLength,
lispUseMapServerAddress }
::= { lispUseMapServerTable 1 }
Schudel, et al. Experimental [Page 45]
RFC 7052 LISP MIB October 2013
LispUseMapServerEntry ::= SEQUENCE {
lispUseMapServerAddressLength Integer32,
lispUseMapServerAddress LispAddressType,
lispUseMapServerState INTEGER
}
lispUseMapServerAddressLength OBJECT-TYPE
SYNTAX Integer32 (5..39)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object is used to get the octet-length of
lispUseMapServerAddress."
::= { lispUseMapServerEntry 1 }
lispUseMapServerAddress OBJECT-TYPE
SYNTAX LispAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Address of a Map-Server configured on this device."
::= { lispUseMapServerEntry 2 }
lispUseMapServerState OBJECT-TYPE
SYNTAX INTEGER {
up (1),
down (2),
unreachable (3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"State of this Map-Server configured on this device
(1 = Map-Server is up; 2 = Map-Server is down)."
::= { lispUseMapServerEntry 3 }
lispUseMapResolverTable OBJECT-TYPE
SYNTAX SEQUENCE OF LispUseMapResolverEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides the properties of the Map-Resolver(s)
this device is configured to use."
REFERENCE
"RFC 6833, Section 4.4."
::= { lispObjects 13 }
lispUseMapResolverEntry OBJECT-TYPE
Schudel, et al. Experimental [Page 46]
RFC 7052 LISP MIB October 2013
SYNTAX LispUseMapResolverEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the
lispUseMapResolverTable."
INDEX { lispUseMapResolverAddressLength,
lispUseMapResolverAddress }
::= { lispUseMapResolverTable 1 }
LispUseMapResolverEntry ::= SEQUENCE {
lispUseMapResolverAddressLength Integer32,
lispUseMapResolverAddress LispAddressType,
lispUseMapResolverState INTEGER
}
lispUseMapResolverAddressLength OBJECT-TYPE
SYNTAX Integer32 (5..39)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object is used to get the octet-length of
lispUseMapResolverAddress."
::= { lispUseMapResolverEntry 1 }
lispUseMapResolverAddress OBJECT-TYPE
SYNTAX LispAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Address of Map-Resolver configured on this device."
::= { lispUseMapResolverEntry 2 }
lispUseMapResolverState OBJECT-TYPE
SYNTAX INTEGER {
up (1),
down (2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"State of this Map-Resolver configured on this device
(1 = Map-Resolver is up; 2 = Map-Resolver is down)."
::= { lispUseMapResolverEntry 3 }
lispUseProxyEtrTable OBJECT-TYPE
SYNTAX SEQUENCE OF LispUseProxyEtrEntry
MAX-ACCESS not-accessible
Schudel, et al. Experimental [Page 47]
RFC 7052 LISP MIB October 2013
STATUS current
DESCRIPTION
"This table provides the properties of all Proxy ETRs that
this device is configured to use."
REFERENCE
"RFC 6830, Section 6."
::= { lispObjects 14 }
lispUseProxyEtrEntry OBJECT-TYPE
SYNTAX LispUseProxyEtrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the
lispUseProxyEtrTable."
INDEX { lispUseProxyEtrAddressLength,
lispUseProxyEtrAddress }
::= { lispUseProxyEtrTable 1 }
LispUseProxyEtrEntry ::= SEQUENCE {
lispUseProxyEtrAddressLength Integer32,
lispUseProxyEtrAddress LispAddressType,
lispUseProxyEtrPriority Integer32,
lispUseProxyEtrWeight Integer32,
lispUseProxyEtrMPriority Integer32,
lispUseProxyEtrMWeight Integer32,
lispUseProxyEtrState INTEGER
}
lispUseProxyEtrAddressLength OBJECT-TYPE
SYNTAX Integer32 (5..39)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object is used to get the octet-length of
lispUseProxyEtrAddress."
::= { lispUseProxyEtrEntry 1 }
lispUseProxyEtrAddress OBJECT-TYPE
SYNTAX LispAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Address of Proxy ETR configured on this device."
::= { lispUseProxyEtrEntry 2 }
lispUseProxyEtrPriority OBJECT-TYPE
SYNTAX Integer32 (0..255)
Schudel, et al. Experimental [Page 48]
RFC 7052 LISP MIB October 2013
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The unicast priority of the PETR locator."
::= { lispUseProxyEtrEntry 3 }
lispUseProxyEtrWeight OBJECT-TYPE
SYNTAX Integer32 (0..100)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The unicast weight of the PETR locator."
::= { lispUseProxyEtrEntry 4 }
lispUseProxyEtrMPriority OBJECT-TYPE
SYNTAX Integer32 (0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The multicast priority of the PETR locator."
::= { lispUseProxyEtrEntry 5 }
lispUseProxyEtrMWeight OBJECT-TYPE
SYNTAX Integer32 (0..100)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The multicast weight of the PETR locator."
::= { lispUseProxyEtrEntry 6 }
lispUseProxyEtrState OBJECT-TYPE
SYNTAX INTEGER {
down (0),
up (1)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"State of this Proxy ETR configured on this device
(0 = Proxy ETR is down; 1 = Proxy ETR is up)."
::= { lispUseProxyEtrEntry 7 }
--
-- Conformance Information
--
lispCompliances OBJECT IDENTIFIER ::= { lispConformance 1 }
lispGroups OBJECT IDENTIFIER ::= { lispConformance 2 }
Schudel, et al. Experimental [Page 49]
RFC 7052 LISP MIB October 2013
--
-- Compliance Statements
--
lispMIBComplianceEtr MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for LISP ETRs. It conveys
whether the device supports the ETR feature, and,
if so, the relevant state associated with that feature."
MODULE -- this module
MANDATORY-GROUPS { lispMIBEtrGroup }
GROUP lispMIBItrGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBPetrGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBPitrGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBMapServerGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBMapResolverGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBEtrExtendedGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBItrExtendedGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBMapServerExtendedGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBTuningParametersGroup
DESCRIPTION
"This group is optional."
Schudel, et al. Experimental [Page 50]
RFC 7052 LISP MIB October 2013
GROUP lispMIBEncapStatisticsGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBDecapStatisticsGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBDiagnosticsGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBVrfGroup
DESCRIPTION
"This group is optional."
::= { lispCompliances 1 }
lispMIBComplianceItr MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for LISP ITRs. It conveys
whether the device supports the ITR feature, and,
if so, the relevant state associated with that feature."
MODULE -- this module
MANDATORY-GROUPS { lispMIBItrGroup }
GROUP lispMIBEtrGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBPetrGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBPitrGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBMapServerGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBMapResolverGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBEtrExtendedGroup
Schudel, et al. Experimental [Page 51]
RFC 7052 LISP MIB October 2013
DESCRIPTION
"This group is optional."
GROUP lispMIBItrExtendedGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBMapServerExtendedGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBTuningParametersGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBEncapStatisticsGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBDecapStatisticsGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBDiagnosticsGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBVrfGroup
DESCRIPTION
"This group is optional."
::= { lispCompliances 2 }
lispMIBCompliancePetr MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for LISP Proxy-ETRs. It
conveys whether the device supports the Proxy-ETR
feature, and, if so, the relevant state associated
with that feature."
MODULE -- this module
MANDATORY-GROUPS { lispMIBPetrGroup }
GROUP lispMIBEtrGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBItrGroup
Schudel, et al. Experimental [Page 52]
RFC 7052 LISP MIB October 2013
DESCRIPTION
"This group is optional."
GROUP lispMIBPitrGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBMapServerGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBMapResolverGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBEtrExtendedGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBItrExtendedGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBMapServerExtendedGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBTuningParametersGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBEncapStatisticsGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBDecapStatisticsGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBDiagnosticsGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBVrfGroup
DESCRIPTION
"This group is optional."
::= { lispCompliances 3 }
Schudel, et al. Experimental [Page 53]
RFC 7052 LISP MIB October 2013
lispMIBCompliancePitr MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for LISP Proxy-ITRs. It
conveys whether the device supports the Proxy-ITR
feature, and, if so, the relevant state associated
with that feature."
MODULE -- this module
MANDATORY-GROUPS { lispMIBPitrGroup }
GROUP lispMIBEtrGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBItrGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBPetrGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBMapServerGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBMapResolverGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBEtrExtendedGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBItrExtendedGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBMapServerExtendedGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBTuningParametersGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBEncapStatisticsGroup
Schudel, et al. Experimental [Page 54]
RFC 7052 LISP MIB October 2013
DESCRIPTION
"This group is optional."
GROUP lispMIBDecapStatisticsGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBDiagnosticsGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBVrfGroup
DESCRIPTION
"This group is optional."
::= { lispCompliances 4 }
lispMIBComplianceMapServer MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for LISP Map Servers. It
conveys whether the device supports the Map Server
feature, and, if so, the relevant state associated
with that feature."
MODULE -- this module
MANDATORY-GROUPS { lispMIBMapServerGroup }
GROUP lispMIBEtrGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBItrGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBPetrGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBPitrGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBMapResolverGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBEtrExtendedGroup
Schudel, et al. Experimental [Page 55]
RFC 7052 LISP MIB October 2013
DESCRIPTION
"This group is optional."
GROUP lispMIBItrExtendedGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBMapServerExtendedGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBTuningParametersGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBEncapStatisticsGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBDecapStatisticsGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBDiagnosticsGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBVrfGroup
DESCRIPTION
"This group is optional."
::= { lispCompliances 5 }
lispMIBComplianceMapResolver MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for LISP Map Resolvers. It
conveys whether the device supports the Map Resolver
feature, and, if so, the relevant state associated
with that feature."
MODULE -- this module
MANDATORY-GROUPS { lispMIBMapResolverGroup }
GROUP lispMIBEtrGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBItrGroup
Schudel, et al. Experimental [Page 56]
RFC 7052 LISP MIB October 2013
DESCRIPTION
"This group is optional."
GROUP lispMIBPetrGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBPitrGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBMapServerGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBEtrExtendedGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBItrExtendedGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBMapServerExtendedGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBTuningParametersGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBEncapStatisticsGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBDecapStatisticsGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBDiagnosticsGroup
DESCRIPTION
"This group is optional."
GROUP lispMIBVrfGroup
DESCRIPTION
"This group is optional."
::= { lispCompliances 6 }
Schudel, et al. Experimental [Page 57]
RFC 7052 LISP MIB October 2013
--
-- Units of Conformance
--
lispMIBEtrGroup OBJECT-GROUP
OBJECTS { lispFeaturesEtrEnabled,
lispMappingDatabaseLsb,
lispMappingDatabaseLocatorRlocPriority,
lispMappingDatabaseLocatorRlocWeight,
lispMappingDatabaseLocatorRlocMPriority,
lispMappingDatabaseLocatorRlocMWeight,
lispMappingDatabaseLocatorRlocState,
lispMappingDatabaseLocatorRlocLocal,
lispConfiguredLocatorRlocState,
lispConfiguredLocatorRlocLocal,
lispUseMapServerState
}
STATUS current
DESCRIPTION
"A collection of objects to support reporting of basic
LISP ETR parameters."
::= { lispGroups 1 }
lispMIBItrGroup OBJECT-GROUP
OBJECTS { lispFeaturesItrEnabled,
lispFeaturesMapCacheSize,
lispMappingDatabaseLsb,
lispMapCacheLocatorRlocPriority,
lispMapCacheLocatorRlocWeight,
lispMapCacheLocatorRlocMPriority,
lispMapCacheLocatorRlocMWeight,
lispMapCacheLocatorRlocState,
lispMapCacheEidTimeStamp,
lispMapCacheEidExpiryTime,
lispUseMapResolverState,
lispUseProxyEtrPriority,
lispUseProxyEtrWeight,
lispUseProxyEtrMPriority,
lispUseProxyEtrMWeight,
lispUseProxyEtrState
}
STATUS current
DESCRIPTION
"A collection of objects to support reporting of basic
LISP ITR parameters."
::= { lispGroups 2 }
Schudel, et al. Experimental [Page 58]
RFC 7052 LISP MIB October 2013
lispMIBPetrGroup OBJECT-GROUP
OBJECTS { lispFeaturesProxyEtrEnabled
}
STATUS current
DESCRIPTION
"A collection of objects to support reporting of basic
LISP Proxy-ETR parameters."
::= { lispGroups 3 }
lispMIBPitrGroup OBJECT-GROUP
OBJECTS { lispFeaturesProxyItrEnabled,
lispConfiguredLocatorRlocState,
lispConfiguredLocatorRlocLocal
}
STATUS current
DESCRIPTION
"A collection of objects to support reporting of basic
LISP Proxy-ITR parameters."
::= { lispGroups 4 }
lispMIBMapServerGroup OBJECT-GROUP
OBJECTS { lispFeaturesMapServerEnabled,
lispEidRegistrationIsRegistered,
lispEidRegistrationLocatorRlocState
}
STATUS current
DESCRIPTION
"A collection of objects to support reporting of basic
LISP Map Server parameters."
::= { lispGroups 5 }
lispMIBMapResolverGroup OBJECT-GROUP
OBJECTS { lispFeaturesMapResolverEnabled
}
STATUS current
DESCRIPTION
"A collection of objects to support reporting of basic
LISP Map Resolver parameters."
::= { lispGroups 6 }
lispMIBEtrExtendedGroup OBJECT-GROUP
OBJECTS { lispFeaturesRlocProbeEnabled,
lispFeaturesEtrAcceptMapDataEnabled,
lispFeaturesEtrAcceptMapDataVerifyEnabled,
lispMappingDatabaseEidPartitioned
}
STATUS current
Schudel, et al. Experimental [Page 59]
RFC 7052 LISP MIB October 2013
DESCRIPTION
"A collection of objects to support reporting of
LISP features and properties on ETRs."
::= { lispGroups 7 }
lispMIBItrExtendedGroup OBJECT-GROUP
OBJECTS { lispFeaturesRlocProbeEnabled,
lispMapCacheEidState,
lispMapCacheEidAuthoritative,
lispMapCacheLocatorRlocTimeStamp,
lispMapCacheLocatorRlocLastPriorityChange,
lispMapCacheLocatorRlocLastWeightChange,
lispMapCacheLocatorRlocLastMPriorityChange,
lispMapCacheLocatorRlocLastMWeightChange,
lispMapCacheLocatorRlocLastStateChange,
lispMapCacheLocatorRlocRtt
}
STATUS current
DESCRIPTION
"A collection of objects to support reporting of
LISP features and properties on ITRs."
::= { lispGroups 8 }
lispMIBMapServerExtendedGroup OBJECT-GROUP
OBJECTS { lispEidRegistrationSiteName,
lispEidRegistrationSiteDescription,
lispEidRegistrationIsRegistered,
lispEidRegistrationFirstTimeStamp,
lispEidRegistrationLastTimeStamp,
lispEidRegistrationLastRegisterSenderLength,
lispEidRegistrationLastRegisterSender,
lispEidRegistrationEtrLastTimeStamp,
lispEidRegistrationEtrTtl,
lispEidRegistrationEtrProxyReply,
lispEidRegistrationEtrWantsMapNotify,
lispEidRegistrationLocatorIsLocal,
lispEidRegistrationLocatorPriority,
lispEidRegistrationLocatorWeight,
lispEidRegistrationLocatorMPriority,
lispEidRegistrationLocatorMWeight
}
STATUS current
DESCRIPTION
"A collection of objects to support the reporting of
LISP features and properties on Map Servers
related to EID registrations."
::= { lispGroups 9 }
Schudel, et al. Experimental [Page 60]
RFC 7052 LISP MIB October 2013
lispMIBTuningParametersGroup OBJECT-GROUP
OBJECTS { lispFeaturesMapCacheLimit,
lispFeaturesEtrMapCacheTtl
}
STATUS current
DESCRIPTION
"A collection of objects used to support the reporting of
parameters used to control LISP behavior and to tune
performance."
::= { lispGroups 10 }
lispMIBEncapStatisticsGroup OBJECT-GROUP
OBJECTS { lispMappingDatabaseTimeStamp,
lispMappingDatabaseEncapOctets,
lispMappingDatabaseEncapPackets,
lispMappingDatabaseLocatorRlocTimeStamp,
lispMappingDatabaseLocatorRlocEncapOctets,
lispMappingDatabaseLocatorRlocEncapPackets,
lispMapCacheEidTimeStamp,
lispMapCacheEidEncapOctets,
lispMapCacheEidEncapPackets,
lispMapCacheLocatorRlocTimeStamp,
lispMapCacheLocatorRlocEncapOctets,
lispMapCacheLocatorRlocEncapPackets,
lispConfiguredLocatorRlocTimeStamp,
lispConfiguredLocatorRlocEncapOctets,
lispConfiguredLocatorRlocEncapPackets
}
STATUS current
DESCRIPTION
"A collection of objects used to support the reporting of
LISP encapsulation statistics for the device."
::= { lispGroups 11 }
lispMIBDecapStatisticsGroup OBJECT-GROUP
OBJECTS { lispMappingDatabaseTimeStamp,
lispMappingDatabaseDecapOctets,
lispMappingDatabaseDecapPackets,
lispMappingDatabaseLocatorRlocTimeStamp,
lispMappingDatabaseLocatorRlocDecapOctets,
lispMappingDatabaseLocatorRlocDecapPackets,
lispMapCacheEidTimeStamp,
lispMapCacheEidDecapOctets,
lispMapCacheEidDecapPackets,
lispMapCacheLocatorRlocTimeStamp,
lispMapCacheLocatorRlocDecapOctets,
lispMapCacheLocatorRlocDecapPackets,
lispConfiguredLocatorRlocTimeStamp,
Schudel, et al. Experimental [Page 61]
RFC 7052 LISP MIB October 2013
lispConfiguredLocatorRlocDecapOctets,
lispConfiguredLocatorRlocDecapPackets
}
STATUS current
DESCRIPTION
"A collection of objects used to support the reporting of
LISP decapsulation statistics for the device."
::= { lispGroups 12 }
lispMIBDiagnosticsGroup OBJECT-GROUP
OBJECTS { lispFeaturesRouterTimeStamp,
lispGlobalStatsMapRequestsIn,
lispGlobalStatsMapRequestsOut,
lispGlobalStatsMapRepliesIn,
lispGlobalStatsMapRepliesOut,
lispGlobalStatsMapRegistersIn,
lispGlobalStatsMapRegistersOut,
lispEidRegistrationAuthenticationErrors,
lispEidRegistrationRlocsMismatch
}
STATUS current
DESCRIPTION
"A collection of objects used to support the reporting of
additional diagnostics related to the LISP control-plane
state of a LISP device."
::= { lispGroups 13 }
lispMIBVrfGroup OBJECT-GROUP
OBJECTS { lispIidToVrfName
}
STATUS current
DESCRIPTION
"A collection of objects used to support reporting of
VRF-related information on a LISP device."
::= { lispGroups 14 }
END
8. Relationship to Other MIB Modules
8.1. MIB Modules Required for IMPORTS
The LISP MIB imports the TEXTUAL-CONVENTION AddressFamilyNumbers from
the IANA-ADDRESS-FAMILY-NUMBERS-MIB DEFINITIONS [IANA].
The LISP MIB imports mib-2, Unsigned32, Counter64, Integer32, and
TimeTicks from SNMPv2-SMI -- [RFC2578].
Schudel, et al. Experimental [Page 62]
RFC 7052 LISP MIB October 2013
The LISP MIB imports TruthValue, TEXTUAL-CONVENTION, TimeStamp, and
TimeTicks from SNMPv2-TC -- [RFC2579].
The LISP MIB imports MODULE-COMPLIANCE from SNMPv2-TC -- [RFC2580].
The LISP MIB imports MplsL3VpnName from MPLS-L3VPN-STD-MIB --
[RFC4382].
9. Security Considerations
There are no management objects defined in this MIB module that have
a MAX-ACCESS clause of read-write and/or read-create. So, if this
MIB module is implemented correctly, then there is no risk that an
intruder can alter or create any management objects of this MIB
module via direct SNMP SET operations.
There are no readable objects in this MIB module (i.e., objects with
a MAX-ACCESS other than not-accessible) that are considered
sensitive.
SNMP versions prior to SNMPv3 did not include adequate security.
Even if the network itself is secure (for example by using IPsec),
there is no control as to who on the secure network is allowed to
access and GET/SET (read/change/create/delete) the objects in this
MIB module.
Implementations SHOULD provide the security features described by the
SNMPv3 framework (see [RFC3410]), and implementations claiming
compliance to the SNMPv3 standard MUST include full support for
authentication and privacy via the User-based Security Model (USM)
[RFC3414] with the AES cipher algorithm [RFC3826]. Implementations
MAY also provide support for the Transport Security Model (TSM)
[RFC5591] in combination with a secure transport such as SSH
[RFC5592] or TLS/DTLS [RFC6353].
Further, deployment of SNMP versions prior to SNMPv3 is NOT
RECOMMENDED. Instead, it is RECOMMENDED to deploy SNMPv3 and to
enable cryptographic security. It is then a customer/operator
responsibility to ensure that the SNMP entity giving access to an
instance of this MIB module is properly configured to give access to
the objects only to those principals (users) that have legitimate
rights to indeed GET or SET (change/create/delete) them.
Schudel, et al. Experimental [Page 63]
RFC 7052 LISP MIB October 2013
10. IANA Considerations
The MIB module in this document uses the following IANA-assigned
OBJECT IDENTIFIER values recorded in the SMI Numbers registry:
Descriptor OBJECT IDENTIFIER value
---------- -----------------------
lispMIB { mib-2 220 }
IANA has allocated a new value in the "SMI Network Management MGMT
Codes Internet-standard MIB" subregistry of the "Network Management
Parameters" registry, according to the following registration data:
Decimal: 220
Name: lispMIB
Description: Locator/ID Separation Protocol (LISP)
References: [RFC7052]
11. References
11.1. Normative References
[IANA] IANA, "IANA-ADDRESS-FAMILY-NUMBERS-MIB DEFINITIONS",
<http://www.iana.org/assignments/
ianaaddressfamilynumbers-mib>.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC2578] McCloghrie, K., Ed., Perkins, D., Ed., and J.
Schoenwaelder, Ed., "Structure of Management Information
Version 2 (SMIv2)", STD 58, RFC 2578, April 1999.
[RFC2579] McCloghrie, K., Ed., Perkins, D., Ed., and J.
Schoenwaelder, Ed., "Textual Conventions for SMIv2",
STD 58, RFC 2579, April 1999.
[RFC2580] McCloghrie, K., Perkins, D., and J. Schoenwaelder,
"Conformance Statements for SMIv2", STD 58, RFC 2580,
April 1999.
[RFC3414] Blumenthal, U. and B. Wijnen, "User-based Security Model
(USM) for version 3 of the Simple Network Management
Protocol (SNMPv3)", STD 62, RFC 3414, December 2002.
Schudel, et al. Experimental [Page 64]
RFC 7052 LISP MIB October 2013
[RFC3826] Blumenthal, U., Maino, F., and K. McCloghrie, "The
Advanced Encryption Standard (AES) Cipher Algorithm in the
SNMP User-based Security Model", RFC 3826, June 2004.
[RFC4382] Nadeau, T. and H. van der Linde, "MPLS/BGP Layer 3 Virtual
Private Network (VPN) Management Information Base",
RFC 4382, February 2006.
[RFC5591] Harrington, D. and W. Hardaker, "Transport Security Model
for the Simple Network Management Protocol (SNMP)",
RFC 5591, June 2009.
[RFC5592] Harrington, D., Salowey, J., and W. Hardaker, "Secure
Shell Transport Model for the Simple Network Management
Protocol (SNMP)", RFC 5592, June 2009.
[RFC6353] Hardaker, W., "Transport Layer Security (TLS) Transport
Model for the Simple Network Management Protocol (SNMP)",
RFC 6353, July 2011.
[RFC6830] Farinacci, D., Fuller, V., Meyer, D., and D. Lewis, "The
Locator/ID Separation Protocol (LISP)", RFC 6830,
January 2013.
[RFC6832] Lewis, D., Meyer, D., Farinacci, D., and V. Fuller,
"Interworking between Locator/ID Separation Protocol
(LISP) and Non-LISP Sites", RFC 6832, January 2013.
[RFC6833] Fuller, V. and D. Farinacci, "Locator/ID Separation
Protocol (LISP) Map-Server Interface", RFC 6833,
January 2013.
11.2. Informative References
[LCAF] Farinacci, D., Meyer, D., and J. Snijders, "LISP Canonical
Address Format (LCAF)", Work in Progress, September 2013.
[RFC3410] Case, J., Mundy, R., Partain, D., and B. Stewart,
"Introduction and Applicability Statements for Internet-
Standard Management Framework", RFC 3410, December 2002.
Schudel, et al. Experimental [Page 65]
RFC 7052 LISP MIB October 2013
Appendix A. Acknowledgments
A thank you is owed to Dino Farinacci for his input, review, and
comments on the initial versions of this document. In addition, the
authors would like to gratefully acknowledge several others who have
reviewed and commented on this document. They include Darrel Lewis,
Isidor Kouvelas, Jesper Skriver, Selina Heimlich, Parna Agrawal, Dan
Romascanu, and Luigi Iannone. Special thanks are owed to Brian
Haberman, the Internet Area AD, for his very detailed review; Miguel
Garcia for reviewing this document as part of the General Area Review
Team; and Harrie Hazewinkel for the detailed MIB review and comments.
Authors' Addresses
Gregg Schudel
Cisco Systems
Tasman Drive
San Jose, CA 95134
USA
EMail: gschudel@cisco.com
Amit Jain
Juniper Networks
1133 Innovation Way
Sunnyvale, CA 94089
USA
EMail: atjain@juniper.net
Victor Moreno
Cisco Systems
Tasman Drive
San Jose, CA 95134
USA
EMail: vimoreno@cisco.com
Schudel, et al. Experimental [Page 66]