<- RFC Index (7301..7400)
RFC 7323
Obsoletes RFC 1323
Internet Engineering Task Force (IETF) D. Borman
Request for Comments: 7323 Quantum Corporation
Obsoletes: 1323 B. Braden
Category: Standards Track University of Southern California
ISSN: 2070-1721 V. Jacobson
Google, Inc.
R. Scheffenegger, Ed.
NetApp, Inc.
September 2014
TCP Extensions for High Performance
Abstract
This document specifies a set of TCP extensions to improve
performance over paths with a large bandwidth * delay product and to
provide reliable operation over very high-speed paths. It defines
the TCP Window Scale (WS) option and the TCP Timestamps (TS) option
and their semantics. The Window Scale option is used to support
larger receive windows, while the Timestamps option can be used for
at least two distinct mechanisms, Protection Against Wrapped
Sequences (PAWS) and Round-Trip Time Measurement (RTTM), that are
also described herein.
This document obsoletes RFC 1323 and describes changes from it.
Status of This Memo
This is an Internet Standards Track document.
This document is a product of the Internet Engineering Task Force
(IETF). It represents the consensus of the IETF community. It has
received public review and has been approved for publication by the
Internet Engineering Steering Group (IESG). Further information on
Internet Standards is available in Section 2 of RFC 5741.
Information about the current status of this document, any errata,
and how to provide feedback on it may be obtained at
http://www.rfc-editor.org/info/rfc7323.
Borman, et al. Standards Track [Page 1]
RFC 7323 TCP Extensions for High Performance September 2014
Copyright Notice
Copyright (c) 2014 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Borman, et al. Standards Track [Page 2]
RFC 7323 TCP Extensions for High Performance September 2014
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 4
1.1. TCP Performance . . . . . . . . . . . . . . . . . . . . . 4
1.2. TCP Reliability . . . . . . . . . . . . . . . . . . . . . 5
1.3. Using TCP options . . . . . . . . . . . . . . . . . . . . 6
1.4. Terminology . . . . . . . . . . . . . . . . . . . . . . . 7
2. TCP Window Scale Option . . . . . . . . . . . . . . . . . . . 8
2.1. Introduction . . . . . . . . . . . . . . . . . . . . . . 8
2.2. Window Scale Option . . . . . . . . . . . . . . . . . . . 8
2.3. Using the Window Scale Option . . . . . . . . . . . . . . 9
2.4. Addressing Window Retraction . . . . . . . . . . . . . . 10
3. TCP Timestamps Option . . . . . . . . . . . . . . . . . . . . 11
3.1. Introduction . . . . . . . . . . . . . . . . . . . . . . 11
3.2. Timestamps Option . . . . . . . . . . . . . . . . . . . . 12
4. The RTTM Mechanism . . . . . . . . . . . . . . . . . . . . . 14
4.1. Introduction . . . . . . . . . . . . . . . . . . . . . . 14
4.2. Updating the RTO Value . . . . . . . . . . . . . . . . . 15
4.3. Which Timestamp to Echo . . . . . . . . . . . . . . . . . 16
5. PAWS - Protection Against Wrapped Sequences . . . . . . . . . 19
5.1. Introduction . . . . . . . . . . . . . . . . . . . . . . 19
5.2. The PAWS Mechanism . . . . . . . . . . . . . . . . . . . 19
5.3. Basic PAWS Algorithm . . . . . . . . . . . . . . . . . . 20
5.4. Timestamp Clock . . . . . . . . . . . . . . . . . . . . . 22
5.5. Outdated Timestamps . . . . . . . . . . . . . . . . . . . 24
5.6. Header Prediction . . . . . . . . . . . . . . . . . . . . 25
5.7. IP Fragmentation . . . . . . . . . . . . . . . . . . . . 26
5.8. Duplicates from Earlier Incarnations of Connection . . . 26
6. Conclusions and Acknowledgments . . . . . . . . . . . . . . . 27
7. Security Considerations . . . . . . . . . . . . . . . . . . . 27
7.1. Privacy Considerations . . . . . . . . . . . . . . . . . 29
8. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 29
9. References . . . . . . . . . . . . . . . . . . . . . . . . . 30
9.1. Normative References . . . . . . . . . . . . . . . . . . 30
9.2. Informative References . . . . . . . . . . . . . . . . . 30
Appendix A. Implementation Suggestions . . . . . . . . . . . . . 34
Appendix B. Duplicates from Earlier Connection Incarnations . . 35
B.1. System Crash with Loss of State . . . . . . . . . . . . . 35
B.2. Closing and Reopening a Connection . . . . . . . . . . . 35
Appendix C. Summary of Notation . . . . . . . . . . . . . . . . 37
Appendix D. Event Processing Summary . . . . . . . . . . . . . . 38
Appendix E. Timestamps Edge Cases . . . . . . . . . . . . . . . 44
Appendix F. Window Retraction Example . . . . . . . . . . . . . 44
Appendix G. RTO Calculation Modification . . . . . . . . . . . . 45
Appendix H. Changes from RFC 1323 . . . . . . . . . . . . . . . 46
Borman, et al. Standards Track [Page 3]
RFC 7323 TCP Extensions for High Performance September 2014
1. Introduction
The TCP protocol [RFC793] was designed to operate reliably over
almost any transmission medium regardless of transmission rate,
delay, corruption, duplication, or reordering of segments. Over the
years, advances in networking technology have resulted in ever-higher
transmission speeds, and the fastest paths are well beyond the domain
for which TCP was originally engineered.
This document defines a set of modest extensions to TCP to extend the
domain of its application to match the increasing network capability.
It is an update to and obsoletes [RFC1323], which in turn is based
upon and obsoletes [RFC1072] and [RFC1185].
Changes between [RFC1323] and this document are detailed in
Appendix H. These changes are partly due to errata in [RFC1323], and
partly due to the improved understanding of how the involved
components interact.
For brevity, the full discussions of the merits and history behind
the TCP options defined within this document have been omitted.
[RFC1323] should be consulted for reference. It is recommended that
a modern TCP stack implements and make use of the extensions
described in this document.
1.1. TCP Performance
TCP performance problems arise when the bandwidth * delay product is
large. A network having such paths is referred to as a "long, fat
network" (LFN).
There are two fundamental performance problems with basic TCP over
LFN paths:
(1) Window Size Limit
The TCP header uses a 16-bit field to report the receive window
size to the sender. Therefore, the largest window that can be
used is 2^16 = 64 KiB. For LFN paths where the bandwidth *
delay product exceeds 64 KiB, the receive window limits the
maximum throughput of the TCP connection over the path, i.e.,
the amount of unacknowledged data that TCP can send in order to
keep the pipeline full.
Borman, et al. Standards Track [Page 4]
RFC 7323 TCP Extensions for High Performance September 2014
To circumvent this problem, Section 2 of this memo defines a TCP
option, "Window Scale", to allow windows larger than 2^16. This
option defines an implicit scale factor, which is used to
multiply the window size value found in a TCP header to obtain
the true window size.
It must be noted that the use of large receive windows increases
the chance of too quickly wrapping sequence numbers, as
described below in Section 1.2, (1).
(2) Recovery from Losses
Packet losses in an LFN can have a catastrophic effect on
throughput.
To generalize the Fast Retransmit / Fast Recovery mechanism to
handle multiple packets dropped per window, Selective
Acknowledgments are required. Unlike the normal cumulative
acknowledgments of TCP, Selective Acknowledgments give the
sender a complete picture of which segments are queued at the
receiver and which have not yet arrived.
Selective Acknowledgments and their use are specified in
separate documents, "TCP Selective Acknowledgment Options"
[RFC2018], "An Extension to the Selective Acknowledgement (SACK)
Option for TCP" [RFC2883], and "A Conservative Loss Recovery
Algorithm Based on Selective Acknowledgment (SACK) for TCP"
[RFC6675], and are not further discussed in this document.
1.2. TCP Reliability
An especially serious kind of error may result from an accidental
reuse of TCP sequence numbers in data segments. TCP reliability
depends upon the existence of a bound on the lifetime of a segment:
the "Maximum Segment Lifetime" or MSL.
Duplication of sequence numbers might happen in either of two ways:
(1) Sequence number wrap-around on the current connection
A TCP sequence number contains 32 bits. At a high enough
transfer rate of large volumes of data (at least 4 GiB in the
same session), the 32-bit sequence space may be "wrapped"
(cycled) within the time that a segment is delayed in queues.
Borman, et al. Standards Track [Page 5]
RFC 7323 TCP Extensions for High Performance September 2014
(2) Earlier incarnation of the connection
Suppose that a connection terminates, either by a proper close
sequence or due to a host crash, and the same connection (i.e.,
using the same pair of port numbers) is immediately reopened. A
delayed segment from the terminated connection could fall within
the current window for the new incarnation and be accepted as
valid.
Duplicates from earlier incarnations, case (2), are avoided by
enforcing the current fixed MSL of the TCP specification, as
explained in Section 5.8 and Appendix B. In addition, the
randomizing of ephemeral ports can also help to probabilistically
reduce the chances of duplicates from earlier connections. However,
case (1), avoiding the reuse of sequence numbers within the same
connection, requires an upper bound on MSL that depends upon the
transfer rate, and at high enough rates, a dedicated mechanism is
required.
A possible fix for the problem of cycling the sequence space would be
to increase the size of the TCP sequence number field. For example,
the sequence number field (and also the acknowledgment field) could
be expanded to 64 bits. This could be done either by changing the
TCP header or by means of an additional option.
Section 5 presents a different mechanism, which we call PAWS, to
extend TCP reliability to transfer rates well beyond the foreseeable
upper limit of network bandwidths. PAWS uses the TCP Timestamps
option defined in Section 3.2 to protect against old duplicates from
the same connection.
1.3. Using TCP options
The extensions defined in this document all use TCP options.
When [RFC1323] was published, there was concern that some buggy TCP
implementation might crash on the first appearance of an option on a
non-<SYN> segment. However, bugs like that can lead to denial-of-
service (DoS) attacks against a TCP. Research has shown that most
TCP implementations will properly handle unknown options on non-<SYN>
segments ([Medina04], [Medina05]). But it is still prudent to be
conservative in what you send, and avoiding buggy TCP implementation
is not the only reason for negotiating TCP options on <SYN> segments.
Borman, et al. Standards Track [Page 6]
RFC 7323 TCP Extensions for High Performance September 2014
The Window Scale option negotiates fundamental parameters of the TCP
session. Therefore, it is only sent during the initial handshake.
Furthermore, the Window Scale option will be sent in a <SYN,ACK>
segment only if the corresponding option was received in the initial
<SYN> segment.
The Timestamps option may appear in any data or <ACK> segment, adding
10 bytes (up to 12 bytes including padding) to the 20-byte TCP
header. It is required that this TCP option will be sent on all
non-<SYN> segments after an exchange of options on the <SYN> segments
has indicated that both sides understand this extension.
Research has shown that the use of the Timestamps option to take
additional RTT samples within each RTT has little effect on the
ultimate retransmission timeout value [Allman99]. However, there are
other uses of the Timestamps option, such as the Eifel mechanism
([RFC3522], [RFC4015]) and PAWS (see Section 5), which improve
overall TCP security and performance. The extra header bandwidth
used by this option should be evaluated for the gains in performance
and security in an actual deployment.
Appendix A contains a recommended layout of the options in TCP
headers to achieve reasonable data field alignment.
Finally, we observe that most of the mechanisms defined in this
document are important for LFNs and/or very high-speed networks. For
low-speed networks, it might be a performance optimization to NOT use
these mechanisms. A TCP vendor concerned about optimal performance
over low-speed paths might consider turning these extensions off for
low-speed paths, or allow a user or installation manager to disable
them.
1.4. Terminology
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in [RFC2119].
In this document, these words will appear with that interpretation
only when in UPPER CASE. Lower case uses of these words are not to
be interpreted as carrying [RFC2119] significance.
Borman, et al. Standards Track [Page 7]
RFC 7323 TCP Extensions for High Performance September 2014
2. TCP Window Scale Option
2.1. Introduction
The window scale extension expands the definition of the TCP window
to 30 bits and then uses an implicit scale factor to carry this
30-bit value in the 16-bit window field of the TCP header (SEG.WND in
[RFC793]). The exponent of the scale factor is carried in a TCP
option, Window Scale. This option is sent only in a <SYN> segment (a
segment with the SYN bit on), hence the window scale is fixed in each
direction when a connection is opened.
The maximum receive window, and therefore the scale factor, is
determined by the maximum receive buffer space. In a typical modern
implementation, this maximum buffer space is set by default but can
be overridden by a user program before a TCP connection is opened.
This determines the scale factor, and therefore no new user interface
is needed for window scaling.
2.2. Window Scale Option
The three-byte Window Scale option MAY be sent in a <SYN> segment by
a TCP. It has two purposes: (1) indicate that the TCP is prepared to
both send and receive window scaling, and (2) communicate the
exponent of a scale factor to be applied to its receive window.
Thus, a TCP that is prepared to scale windows SHOULD send the option,
even if its own scale factor is 1 and the exponent 0. The scale
factor is limited to a power of two and encoded logarithmically, so
it may be implemented by binary shift operations. The maximum scale
exponent is limited to 14 for a maximum permissible receive window
size of 1 GiB (2^(14+16)).
TCP Window Scale option (WSopt):
Kind: 3
Length: 3 bytes
+---------+---------+---------+
| Kind=3 |Length=3 |shift.cnt|
+---------+---------+---------+
1 1 1
This option is an offer, not a promise; both sides MUST send Window
Scale options in their <SYN> segments to enable window scaling in
either direction. If window scaling is enabled, then the TCP that
sent this option will right-shift its true receive-window values by
'shift.cnt' bits for transmission in SEG.WND. The value 'shift.cnt'
Borman, et al. Standards Track [Page 8]
RFC 7323 TCP Extensions for High Performance September 2014
MAY be zero (offering to scale, while applying a scale factor of 1 to
the receive window).
This option MAY be sent in an initial <SYN> segment (i.e., a segment
with the SYN bit on and the ACK bit off). If a Window Scale option
was received in the initial <SYN> segment, then this option MAY be
sent in the <SYN,ACK> segment. A Window Scale option in a segment
without a SYN bit MUST be ignored.
The window field in a segment where the SYN bit is set (i.e., a <SYN>
or <SYN,ACK>) MUST NOT be scaled.
2.3. Using the Window Scale Option
A model implementation of window scaling is as follows, using the
notation of [RFC793]:
o The connection state is augmented by two window shift counters,
Snd.Wind.Shift and Rcv.Wind.Shift, to be applied to the incoming
and outgoing window fields, respectively.
o If a TCP receives a <SYN> segment containing a Window Scale
option, it SHOULD send its own Window Scale option in the
<SYN,ACK> segment.
o The Window Scale option MUST be sent with shift.cnt = R, where R
is the value that the TCP would like to use for its receive
window.
o Upon receiving a <SYN> segment with a Window Scale option
containing shift.cnt = S, a TCP MUST set Snd.Wind.Shift to S and
MUST set Rcv.Wind.Shift to R; otherwise, it MUST set both
Snd.Wind.Shift and Rcv.Wind.Shift to zero.
o The window field (SEG.WND) in the header of every incoming
segment, with the exception of <SYN> segments, MUST be left-
shifted by Snd.Wind.Shift bits before updating SND.WND:
SND.WND = SEG.WND << Snd.Wind.Shift
(assuming the other conditions of [RFC793] are met, and using the
"C" notation "<<" for left-shift).
o The window field (SEG.WND) of every outgoing segment, with the
exception of <SYN> segments, MUST be right-shifted by
Rcv.Wind.Shift bits:
SEG.WND = RCV.WND >> Rcv.Wind.Shift
Borman, et al. Standards Track [Page 9]
RFC 7323 TCP Extensions for High Performance September 2014
TCP determines if a data segment is "old" or "new" by testing whether
its sequence number is within 2^31 bytes of the left edge of the
window, and if it is not, discarding the data as "old". To insure
that new data is never mistakenly considered old and vice versa, the
left edge of the sender's window has to be at most 2^31 away from the
right edge of the receiver's window. The same is true of the
sender's right edge and receiver's left edge. Since the right and
left edges of either the sender's or receiver's window differ by the
window size, and since the sender and receiver windows can be out of
phase by at most the window size, the above constraints imply that
two times the maximum window size must be less than 2^31, or
max window < 2^30
Since the max window is 2^S (where S is the scaling shift count)
times at most 2^16 - 1 (the maximum unscaled window), the maximum
window is guaranteed to be < 2^30 if S <= 14. Thus, the shift count
MUST be limited to 14 (which allows windows of 2^30 = 1 GiB). If a
Window Scale option is received with a shift.cnt value larger than
14, the TCP SHOULD log the error but MUST use 14 instead of the
specified value. This is safe as a sender can always choose to only
partially use any signaled receive window. If the receiver is
scaling by a factor larger than 14 and the sender is only scaling by
14, then the receive window used by the sender will appear smaller
than it is in reality.
The scale factor applies only to the window field as transmitted in
the TCP header; each TCP using extended windows will maintain the
window values locally as 32-bit numbers. For example, the
"congestion window" computed by slow start and congestion avoidance
(see [RFC5681]) is not affected by the scale factor, so window
scaling will not introduce quantization into the congestion window.
2.4. Addressing Window Retraction
When a non-zero scale factor is in use, there are instances when a
retracted window can be offered -- see Appendix F for a detailed
example. The end of the window will be on a boundary based on the
granularity of the scale factor being used. If the sequence number
is then updated by a number of bytes smaller than that granularity,
the TCP will have to either advertise a new window that is beyond
what it previously advertised (and perhaps beyond the buffer) or will
have to advertise a smaller window, which will cause the TCP window
to shrink. Implementations MUST ensure that they handle a shrinking
window, as specified in Section 4.2.2.16 of [RFC1122].
Borman, et al. Standards Track [Page 10]
RFC 7323 TCP Extensions for High Performance September 2014
For the receiver, this implies that:
1) The receiver MUST honor, as in window, any segment that would
have been in window for any <ACK> sent by the receiver.
2) When window scaling is in effect, the receiver SHOULD track the
actual maximum window sequence number (which is likely to be
greater than the window announced by the most recent <ACK>, if
more than one segment has arrived since the application consumed
any data in the receive buffer).
On the sender side:
3) The initial transmission MUST be within the window announced by
the most recent <ACK>.
4) On first retransmission, or if the sequence number is out of
window by less than 2^Rcv.Wind.Shift, then do normal
retransmission(s) without regard to the receiver window as long
as the original segment was in window when it was sent.
5) Subsequent retransmissions MAY only be sent if they are within
the window announced by the most recent <ACK>.
3. TCP Timestamps Option
3.1. Introduction
The Timestamps option is introduced to address some of the issues
mentioned in Sections 1.1 and 1.2. The Timestamps option is
specified in a symmetrical manner, so that Timestamp Value (TSval)
timestamps are carried in both data and <ACK> segments and are echoed
in Timestamp Echo Reply (TSecr) fields carried in returning <ACK> or
data segments. Originally used primarily for timestamping individual
segments, the properties of the Timestamps option allow for taking
time measurements (Section 4) as well as additional uses (Section 5).
It is necessary to remember that there is a distinction between the
Timestamps option conveying timestamp information and the use of that
information. In particular, the RTTM mechanism must be viewed
independently from updating the Retransmission Timeout (RTO) (see
Section 4.2). In this case, the sample granularity also needs to be
taken into account. Other mechanisms, such as PAWS or Eifel, are not
built upon the timestamp information itself but are based on the
intrinsic property of monotonically non-decreasing values.
The Timestamps option is important when large receive windows are
used to allow the use of the PAWS mechanism (see Section 5).
Borman, et al. Standards Track [Page 11]
RFC 7323 TCP Extensions for High Performance September 2014
Furthermore, the option may be useful for all TCPs, since it
simplifies the sender and allows the use of additional optimizations
such as Eifel ([RFC3522], [RFC4015]) and others ([RFC6817],
[Kuzmanovic03], [Kuehlewind10]).
3.2. Timestamps Option
TCP is a symmetric protocol, allowing data to be sent at any time in
either direction, and therefore timestamp echoing may occur in either
direction. For simplicity and symmetry, we specify that timestamps
always be sent and echoed in both directions. For efficiency, we
combine the timestamp and timestamp reply fields into a single TCP
Timestamps option.
TCP Timestamps option (TSopt):
Kind: 8
Length: 10 bytes
+-------+-------+---------------------+---------------------+
|Kind=8 | 10 | TS Value (TSval) |TS Echo Reply (TSecr)|
+-------+-------+---------------------+---------------------+
1 1 4 4
The Timestamps option carries two four-byte timestamp fields. The
TSval field contains the current value of the timestamp clock of the
TCP sending the option.
The TSecr field is valid if the ACK bit is set in the TCP header. If
the ACK bit is not set in the outgoing TCP header, the sender of that
segment SHOULD set the TSecr field to zero. When the ACK bit is set
in an outgoing segment, the sender MUST echo a recently received
TSval sent by the remote TCP in the TSval field of a Timestamps
option. The exact rules on which TSval MUST be echoed are given in
Section 4.3. When the ACK bit is not set, the receiver MUST ignore
the value of the TSecr field.
A TCP MAY send the TSopt in an initial <SYN> segment (i.e., segment
containing a SYN bit and no ACK bit), and MAY send a TSopt in
<SYN,ACK> only if it received a TSopt in the initial <SYN> segment
for the connection.
Once TSopt has been successfully negotiated, that is both <SYN> and
<SYN,ACK> contain TSopt, the TSopt MUST be sent in every non-<RST>
segment for the duration of the connection, and SHOULD be sent in an
<RST> segment (see Section 5.2 for details). The TCP SHOULD remember
this state by setting a flag, referred to as Snd.TS.OK, to one. If a
Borman, et al. Standards Track [Page 12]
RFC 7323 TCP Extensions for High Performance September 2014
non-<RST> segment is received without a TSopt, a TCP SHOULD silently
drop the segment. A TCP MUST NOT abort a TCP connection because any
segment lacks an expected TSopt.
Implementations are strongly encouraged to follow the above rules for
handling a missing Timestamps option and the order of precedence
mentioned in Section 5.3 when deciding on the acceptance of a
segment.
If a receiver chooses to accept a segment without an expected
Timestamps option, it must be clear that undetectable data corruption
may occur.
Such a TCP receiver may experience undetectable wrapped-sequence
effects, such as data (payload) corruption or session stalls. In
order to maintain the integrity of the payload data, in particular on
high-speed networks, it is paramount to follow the described
processing rules.
However, it has been mentioned that under some circumstances, the
above guidelines are too strict, and some paths sporadically suppress
the Timestamps option, while maintaining payload integrity. A path
behaving in this manner should be deemed unacceptable, but it has
been noted that some implementations relax the acceptance rules as a
workaround and allow TCP to run across such paths [RE-1323BIS].
If a TSopt is received on a connection where TSopt was not negotiated
in the initial three-way handshake, the TSopt MUST be ignored and the
packet processed normally.
In the case of crossing <SYN> segments where one <SYN> contains a
TSopt and the other doesn't, both sides MAY send a TSopt in the
<SYN,ACK> segment.
TSopt is required for the two mechanisms described in Sections 4 and
5. There are also other mechanisms that rely on the presence of the
TSopt, e.g., [RFC3522]. If a TCP stopped sending TSopt at any time
during an established session, it interferes with these mechanisms.
This update to [RFC1323] describes explicitly the previous assumption
(see Section 5.2) that each TCP segment must have a TSopt, once
negotiated.
Borman, et al. Standards Track [Page 13]
RFC 7323 TCP Extensions for High Performance September 2014
4. The RTTM Mechanism
4.1. Introduction
One use of the Timestamps option is to measure the round-trip time
(RTT) of virtually every packet acknowledged. The RTTM mechanism
requires a Timestamps option in every measured segment, with a TSval
that is obtained from a (virtual) "timestamp clock". Values of this
clock MUST be at least approximately proportional to real time, in
order to measure actual RTT.
TCP measures the RTT, primarily for the purpose of arriving at a
reasonable value for the RTO timer interval. Accurate and current
RTT estimates are necessary to adapt to changing traffic conditions,
while a conservative estimate of the RTO interval is necessary to
minimize spurious RTOs.
These TSval values are echoed in TSecr values in the reverse
direction. The difference between a received TSecr value and the
current timestamp clock value provides an RTT measurement.
When timestamps are used, every segment that is received will contain
a TSecr value. However, these values cannot all be used to update
the measured RTT. The following example illustrates why. It shows a
one-way data flow with segments arriving in sequence without loss.
Here A, B, C... represent data blocks occupying successive blocks of
sequence numbers, and ACK(A),... represent the corresponding
cumulative acknowledgments. The two timestamp fields of the
Timestamps option are shown symbolically as <TSval=x,TSecr=y>. Each
TSecr field contains the value most recently received in a TSval
field.
Borman, et al. Standards Track [Page 14]
RFC 7323 TCP Extensions for High Performance September 2014
TCP A TCP B
<A,TSval=1,TSecr=120> ----->
<---- <ACK(A),TSval=127,TSecr=1>
<B,TSval=5,TSecr=127> ----->
<---- <ACK(B),TSval=131,TSecr=5>
. . . . . . . . . . . . . . . . . . . . . .
<C,TSval=65,TSecr=131> ---->
<---- <ACK(C),TSval=191,TSecr=65>
(etc.)
The dotted line marks a pause (60 time units long) in which A had
nothing to send. Note that this pause inflates the RTT, which B
could infer from receiving TSecr=131 in data segment C. Thus, in
one-way data flows, RTTM in the reverse direction measures a value
that is inflated by gaps in sending data. However, the following
rule prevents a resulting inflation of the measured RTT:
RTTM Rule: A TSecr value received in a segment MAY be used to update
the averaged RTT measurement only if the segment advances
the left edge of the send window, i.e., SND.UNA is
increased.
Since TCP B is not sending data, the data segment C does not
acknowledge any new data when it arrives at B. Thus, the inflated
RTTM measurement is not used to update B's RTTM measurement.
4.2. Updating the RTO Value
When [RFC1323] was originally written, it was perceived that taking
RTT measurements for each segment, and also during retransmissions,
would contribute to reduce spurious RTOs, while maintaining the
timeliness of necessary RTOs. At the time, RTO was also the only
mechanism to make use of the measured RTT. It has been shown that
taking more RTT samples has only a very limited effect to optimize
RTOs [Allman99].
Implementers should note that with timestamps, multiple RTTMs can be
taken per RTT. The [RFC6298] RTT estimator has weighting factors,
alpha and beta, based on an implicit assumption that at most one RTTM
will be sampled per RTT. When multiple RTTMs per RTT are available
Borman, et al. Standards Track [Page 15]
RFC 7323 TCP Extensions for High Performance September 2014
to update the RTT estimator, an implementation SHOULD try to adhere
to the spirit of the history specified in [RFC6298]. An
implementation suggestion is detailed in Appendix G.
[Ludwig00] and [Floyd05] have highlighted the problem that an
unmodified RTO calculation, which is updated with per-packet RTT
samples, will truncate the path history too soon. This can lead to
an increase in spurious retransmissions, when the path properties
vary in the order of a few RTTs, but a high number of RTT samples are
taken on a much shorter timescale.
4.3. Which Timestamp to Echo
If more than one Timestamps option is received before a reply segment
is sent, the TCP must choose only one of the TSvals to echo, ignoring
the others. To minimize the state kept in the receiver (i.e., the
number of unprocessed TSvals), the receiver should be required to
retain at most one timestamp in the connection control block.
There are three situations to consider:
(A) Delayed ACKs.
Many TCPs acknowledge only every second segment out of a group
of segments arriving within a short time interval; this policy
is known generally as "delayed ACKs". The data-sender TCP must
measure the effective RTT, including the additional time due to
delayed ACKs, or else it will retransmit unnecessarily. Thus,
when delayed ACKs are in use, the receiver SHOULD reply with the
TSval field from the earliest unacknowledged segment.
(B) A hole in the sequence space (segment(s) has been lost).
The sender will continue sending until the window is filled, and
the receiver may be generating <ACK>s as these out-of-order
segments arrive (e.g., to aid "Fast Retransmit").
The lost segment is probably a sign of congestion, and in that
situation the sender should be conservative about
retransmission. Furthermore, it is better to overestimate than
underestimate the RTT. An <ACK> for an out-of-order segment
SHOULD, therefore, contain the timestamp from the most recent
segment that advanced RCV.NXT.
The same situation occurs if segments are reordered by the
network.
Borman, et al. Standards Track [Page 16]
RFC 7323 TCP Extensions for High Performance September 2014
(C) A filled hole in the sequence space.
The segment that fills the hole and advances the window
represents the most recent measurement of the network
characteristics. An RTT computed from an earlier segment would
probably include the sender's retransmit timeout, badly biasing
the sender's average RTT estimate. Thus, the timestamp from the
latest segment (which filled the hole) MUST be echoed.
An algorithm that covers all three cases is described in the
following rules for Timestamps option processing on a synchronized
connection:
(1) The connection state is augmented with two 32-bit slots:
TS.Recent holds a timestamp to be echoed in TSecr whenever a
segment is sent, and Last.ACK.sent holds the ACK field from the
last segment sent. Last.ACK.sent will equal RCV.NXT except when
<ACK>s have been delayed.
(2) If:
SEG.TSval >= TS.Recent and SEG.SEQ <= Last.ACK.sent
then SEG.TSval is copied to TS.Recent; otherwise, it is ignored.
(3) When a TSopt is sent, its TSecr field is set to the current
TS.Recent value.
The following examples illustrate these rules. Here A, B, C...
represent data segments occupying successive blocks of sequence
numbers, and ACK(A),... represent the corresponding acknowledgment
segments. Note that ACK(A) has the same sequence number as B. We
show only one direction of timestamp echoing, for clarity.
Borman, et al. Standards Track [Page 17]
RFC 7323 TCP Extensions for High Performance September 2014
o Segments arrive in sequence, and some of the <ACK>s are delayed.
By case (A), the timestamp from the oldest unacknowledged segment
is echoed.
TS.Recent
<A, TSval=1> ------------------->
1
<B, TSval=2> ------------------->
1
<C, TSval=3> ------------------->
1
<---- <ACK(C), TSecr=1>
(etc.)
o Segments arrive out of order, and every segment is acknowledged.
By case (B), the timestamp from the last segment that advanced the
left window edge is echoed until the missing segment arrives; it
is echoed according to case (C). The same sequence would occur if
segments B and D were lost and retransmitted.
TS.Recent
<A, TSval=1> ------------------->
1
<---- <ACK(A), TSecr=1>
1
<C, TSval=3> ------------------->
1
<---- <ACK(A), TSecr=1>
1
<B, TSval=2> ------------------->
2
<---- <ACK(C), TSecr=2>
2
<E, TSval=5> ------------------->
2
<---- <ACK(C), TSecr=2>
2
<D, TSval=4> ------------------->
4
<---- <ACK(E), TSecr=4>
(etc.)
Borman, et al. Standards Track [Page 18]
RFC 7323 TCP Extensions for High Performance September 2014
5. PAWS - Protection Against Wrapped Sequences
5.1. Introduction
Another use for the Timestamps option is the PAWS mechanism.
Section 5.2 describes a simple mechanism to reject old duplicate
segments that might corrupt an open TCP connection. PAWS operates
within a single TCP connection, using state that is saved in the
connection control block. Section 5.8 and Appendix H discuss the
implications of the PAWS mechanism for avoiding old duplicates from
previous incarnations of the same connection.
5.2. The PAWS Mechanism
PAWS uses the TCP Timestamps option described earlier and assumes
that every received TCP segment (including data and <ACK> segments)
contains a timestamp SEG.TSval whose values are monotonically non-
decreasing in time. The basic idea is that a segment can be
discarded as an old duplicate if it is received with a timestamp
SEG.TSval less than some timestamps recently received on this
connection.
In the PAWS mechanism, the "timestamps" are 32-bit unsigned integers
in a modular 32-bit space. Thus, "less than" is defined the same way
it is for TCP sequence numbers, and the same implementation
techniques apply. If s and t are timestamp values,
s < t if 0 < (t - s) < 2^31,
computed in unsigned 32-bit arithmetic.
The choice of incoming timestamps to be saved for this comparison
MUST guarantee a value that is monotonically non-decreasing. For
example, an implementation might save the timestamp from the segment
that last advanced the left edge of the receive window, i.e., the
most recent in-sequence segment. For simplicity, the value TS.Recent
introduced in Section 4.3 is used instead, as using a common value
for both PAWS and RTTM simplifies the implementation. As Section 4.3
explained, TS.Recent differs from the timestamp from the last in-
sequence segment only in the case of delayed <ACK>s, and therefore by
less than one window. Either choice will, therefore, protect against
sequence number wrap-around.
PAWS submits all incoming segments to the same test, and therefore
protects against duplicate <ACK> segments as well as data segments.
(An alternative non-symmetric algorithm would protect against old
duplicate <ACK>s: the sender of data would reject incoming <ACK>
segments whose TSecr values were less than the TSecr saved from the
Borman, et al. Standards Track [Page 19]
RFC 7323 TCP Extensions for High Performance September 2014
last segment whose ACK field advanced the left edge of the send
window. This algorithm was deemed to lack economy of mechanism and
symmetry.)
TSval timestamps sent on <SYN> and <SYN,ACK> segments are used to
initialize PAWS. PAWS protects against old duplicate non-<SYN>
segments and duplicate <SYN> segments received while there is a
synchronized connection. Duplicate <SYN> and <SYN,ACK> segments
received when there is no connection will be discarded by the normal
3-way handshake and sequence number checks of TCP.
[RFC1323] recommended that <RST> segments NOT carry timestamps and
that they be acceptable regardless of their timestamp. At that time,
the thinking was that old duplicate <RST> segments should be
exceedingly unlikely, and their cleanup function should take
precedence over timestamps. More recently, discussions about various
blind attacks on TCP connections have raised the suggestion that if
the Timestamps option is present, SEG.TSecr could be used to provide
stricter acceptance tests for <RST> segments.
While still under discussion, to enable research into this area it is
now RECOMMENDED that when generating an <RST>, if the segment causing
the <RST> to be generated contains a Timestamps option, the <RST>
should also contain a Timestamps option. In the <RST> segment,
SEG.TSecr SHOULD be set to SEG.TSval from the incoming segment and
SEG.TSval SHOULD be set to zero. If an <RST> is being generated
because of a user abort, and Snd.TS.OK is set, then a Timestamps
option SHOULD be included in the <RST>. When an <RST> segment is
received, it MUST NOT be subjected to the PAWS check by verifying an
acceptable value in SEG.TSval, and information from the Timestamps
option MUST NOT be used to update connection state information.
SEG.TSecr MAY be used to provide stricter <RST> acceptance checks.
5.3. Basic PAWS Algorithm
If the PAWS algorithm is used, the following processing MUST be
performed on all incoming segments for a synchronized connection.
Also, PAWS processing MUST take precedence over the regular TCP
acceptability check (Section 3.3 in [RFC793]), which is performed
after verification of the received Timestamps option:
R1) If there is a Timestamps option in the arriving segment,
SEG.TSval < TS.Recent, TS.Recent is valid (see later
discussion), and if the RST bit is not set, then treat the
arriving segment as not acceptable:
Send an acknowledgment in reply as specified in Section 3.9
of [RFC793], page 69, and drop the segment.
Borman, et al. Standards Track [Page 20]
RFC 7323 TCP Extensions for High Performance September 2014
Note: it is necessary to send an <ACK> segment in order to
retain TCP's mechanisms for detecting and recovering from
half-open connections. For an example, see Figure 10 of
[RFC793].
R2) If the segment is outside the window, reject it (normal TCP
processing).
R3) If an arriving segment satisfies SEG.TSval >= TS.Recent and
SEG.SEQ <= Last.ACK.sent (see Section 4.3), then record its
timestamp in TS.Recent.
R4) If an arriving segment is in sequence (i.e., at the left window
edge), then accept it normally.
R5) Otherwise, treat the segment as a normal in-window,
out-of-sequence TCP segment (e.g., queue it for later delivery
to the user).
Steps R2, R4, and R5 are the normal TCP processing steps specified by
[RFC793].
It is important to note that the timestamp MUST be checked only when
a segment first arrives at the receiver, regardless of whether it is
in sequence or it must be queued for later delivery.
Consider the following example.
Suppose the segment sequence: A.1, B.1, C.1, ..., Z.1 has been
sent, where the letter indicates the sequence number and the digit
represents the timestamp. Suppose also that segment B.1 has been
lost. The timestamp in TS.Recent is 1 (from A.1), so C.1, ...,
Z.1 are considered acceptable and are queued. When B is
retransmitted as segment B.2 (using the latest timestamp), it
fills the hole and causes all the segments through Z to be
acknowledged and passed to the user. The timestamps of the queued
segments are *not* inspected again at this time, since they have
already been accepted. When B.2 is accepted, TS.Recent is set to
2.
This rule allows reasonable performance under loss. A full window of
data is in transit at all times, and after a loss a full window less
one segment will show up out of sequence to be queued at the receiver
(e.g., up to ~2^30 bytes of data); the Timestamps option must not
result in discarding this data.
Borman, et al. Standards Track [Page 21]
RFC 7323 TCP Extensions for High Performance September 2014
In certain unlikely circumstances, the algorithm of rules R1-R5 could
lead to discarding some segments unnecessarily, as shown in the
following example:
Suppose again that segments: A.1, B.1, C.1, ..., Z.1 have been
sent in sequence and that segment B.1 has been lost. Furthermore,
suppose delivery of some of C.1, ... Z.1 is delayed until *after*
the retransmission B.2 arrives at the receiver. These delayed
segments will be discarded unnecessarily when they do arrive,
since their timestamps are now out of date.
This case is very unlikely to occur. If the retransmission was
triggered by a timeout, some of the segments C.1, ... Z.1 must have
been delayed longer than the RTO time. This is presumably an
unlikely event, or there would be many spurious timeouts and
retransmissions. If B's retransmission was triggered by the "Fast
Retransmit" algorithm, i.e., by duplicate <ACK>s, then the queued
segments that caused these <ACK>s must have been received already.
Even if a segment were delayed past the RTO, the Fast Retransmit
mechanism [Jacobson90c] will cause the delayed segments to be
retransmitted at the same time as B.2, avoiding an extra RTT and,
therefore, causing a very small performance penalty.
We know of no case with a significant probability of occurrence in
which timestamps will cause performance degradation by unnecessarily
discarding segments.
5.4. Timestamp Clock
It is important to understand that the PAWS algorithm does not
require clock synchronization between the sender and receiver. The
sender's timestamp clock is used as a source of monotonic non-
decreasing values to stamp the segments. The receiver treats the
timestamp value as simply a monotonically non-decreasing serial
number, without any connection to time. From the receiver's
viewpoint, the timestamp is acting as a logical extension of the
high-order bits of the sequence number.
The receiver algorithm does place some requirements on the frequency
of the timestamp clock.
Borman, et al. Standards Track [Page 22]
RFC 7323 TCP Extensions for High Performance September 2014
(a) The timestamp clock must not be "too slow".
It MUST tick at least once for each 2^31 bytes sent. In fact,
in order to be useful to the sender for round-trip timing, the
clock SHOULD tick at least once per window's worth of data, and
even with the window extension defined in Section 2.2, 2^31
bytes must be at least two windows.
To make this more quantitative, any clock faster than 1 tick/sec
will reject old duplicate segments for link speeds of ~8 Gbps.
A 1 ms timestamp clock will work at link speeds up to 8 Tbps
(8*10^12) bps!
(b) The timestamp clock must not be "too fast".
The recycling time of the timestamp clock MUST be greater than
MSL seconds. Since the clock (timestamp) is 32 bits and the
worst-case MSL is 255 seconds, the maximum acceptable clock
frequency is one tick every 59 ns.
However, it is desirable to establish a much longer recycle
period, in order to handle outdated timestamps on idle
connections (see Section 5.5), and to relax the MSL requirement
for preventing sequence number wrap-around. With a 1 ms
timestamp clock, the 32-bit timestamp will wrap its sign bit in
24.8 days. Thus, it will reject old duplicates on the same
connection if MSL is 24.8 days or less. This appears to be a
very safe figure; an MSL of 24.8 days or longer can probably be
assumed in the Internet without requiring precise MSL
enforcement.
Based upon these considerations, we choose a timestamp clock
frequency in the range 1 ms to 1 sec per tick. This range also
matches the requirements of the RTTM mechanism, which does not need
much more resolution than the granularity of the retransmit timer,
e.g., tens or hundreds of milliseconds.
The PAWS mechanism also puts a strong monotonicity requirement on the
sender's timestamp clock. The method of implementation of the
timestamp clock to meet this requirement depends upon the system
hardware and software.
o Some hosts have a hardware clock that is guaranteed to be
monotonic between hardware resets.
o A clock interrupt may be used to simply increment a binary integer
by 1 periodically.
Borman, et al. Standards Track [Page 23]
RFC 7323 TCP Extensions for High Performance September 2014
o The timestamp clock may be derived from a system clock that is
subject to being abruptly changed by adding a variable offset
value. This offset is initialized to zero. When a new timestamp
clock value is needed, the offset can be adjusted as necessary to
make the new value equal to or larger than the previous value
(which was saved for this purpose).
o A random offset may be added to the timestamp clock on a per-
connection basis. See [RFC6528], Section 3, on randomizing the
initial sequence number (ISN). The same function with a different
secret key can be used to generate the per-connection timestamp
offset.
5.5. Outdated Timestamps
If a connection remains idle long enough for the timestamp clock of
the other TCP to wrap its sign bit, then the value saved in TS.Recent
will become too old; as a result, the PAWS mechanism will cause all
subsequent segments to be rejected, freezing the connection (until
the timestamp clock wraps its sign bit again).
With the chosen range of timestamp clock frequencies (1 sec to 1 ms),
the time to wrap the sign bit will be between 24.8 days and 24800
days. A TCP connection that is idle for more than 24 days and then
comes to life is exceedingly unusual. However, it is undesirable in
principle to place any limitation on TCP connection lifetimes.
We therefore require that an implementation of PAWS include a
mechanism to "invalidate" the TS.Recent value when a connection is
idle for more than 24 days. (An alternative solution to the problem
of outdated timestamps would be to send keep-alive segments at a very
low rate, but still more often than the wrap-around time for
timestamps, e.g., once a day. This would impose negligible overhead.
However, the TCP specification has never included keep-alives, so the
solution based upon invalidation was chosen.)
Note that a TCP does not know the frequency, and therefore the wrap-
around time, of the other TCP, so it must assume the worst. The
validity of TS.Recent needs to be checked only if the basic PAWS
timestamp check fails, i.e., only if SEG.TSval < TS.Recent. If
TS.Recent is found to be invalid, then the segment is accepted,
regardless of the failure of the timestamp check, and rule R3 updates
TS.Recent with the TSval from the new segment.
To detect how long the connection has been idle, the TCP MAY update a
clock or timestamp value associated with the connection whenever
TS.Recent is updated, for example. The details will be
implementation dependent.
Borman, et al. Standards Track [Page 24]
RFC 7323 TCP Extensions for High Performance September 2014
5.6. Header Prediction
"Header prediction" [Jacobson90a] is a high-performance transport
protocol implementation technique that is most important for high-
speed links. This technique optimizes the code for the most common
case, receiving a segment correctly and in order. Using header
prediction, the receiver asks the question, "Is this segment the next
in sequence?" This question can be answered in fewer machine
instructions than the question, "Is this segment within the window?"
Adding header prediction to our timestamp procedure leads to the
following recommended sequence for processing an arriving TCP
segment:
H1) Check timestamp (same as step R1 above).
H2) Do header prediction: if the segment is next in sequence and if
there are no special conditions requiring additional processing,
accept the segment, record its timestamp, and skip H3.
H3) Process the segment normally, as specified in RFC 793. This
includes dropping segments that are outside the window and
possibly sending acknowledgments, and queuing in-window,
out-of-sequence segments.
Another possibility would be to interchange steps H1 and H2, i.e., to
perform the header prediction step H2 *first*, and perform H1 and H3
only when header prediction fails. This could be a performance
improvement, since the timestamp check in step H1 is very unlikely to
fail, and it requires unsigned modulo arithmetic. To perform this
check on every single segment is contrary to the philosophy of header
prediction. We believe that this change might produce a measurable
reduction in CPU time for TCP protocol processing on high-speed
networks.
However, putting H2 first would create a hazard: a segment from 2^32
bytes in the past might arrive at exactly the wrong time and be
accepted mistakenly by the header-prediction step. The following
reasoning has been introduced in [RFC1185] to show that the
probability of this failure is negligible.
If all segments are equally likely to show up as old duplicates,
then the probability of an old duplicate exactly matching the left
window edge is the maximum segment size (MSS) divided by the size
of the sequence space. This ratio must be less than 2^-16, since
MSS must be < 2^16; for example, it will be (2^12)/(2^32) = 2^-20
for [a 100 Mbit/s] link. However, the older a segment is, the
less likely it is to be retained in the Internet, and under any
Borman, et al. Standards Track [Page 25]
RFC 7323 TCP Extensions for High Performance September 2014
reasonable model of segment lifetime the probability of an old
duplicate exactly at the left window edge must be much smaller
than 2^-16.
The 16 bit TCP checksum also allows a basic unreliability of one
part in 2^16. A protocol mechanism whose reliability exceeds the
reliability of the TCP checksum should be considered "good
enough", i.e., it won't contribute significantly to the overall
error rate. We therefore believe we can ignore the problem of an
old duplicate being accepted by doing header prediction before
checking the timestamp. [Note: the notation for exponentiation
has been changed from how it appeared in RFC 1185.]
However, this probabilistic argument is not universally accepted, and
the consensus at present is that the performance gain does not
justify the hazard in the general case. It is therefore recommended
that H2 follow H1.
5.7. IP Fragmentation
At high data rates, the protection against old segments provided by
PAWS can be circumvented by errors in IP fragment reassembly (see
[RFC4963]). The only way to protect against incorrect IP fragment
reassembly is to not allow the segments to be fragmented. This is
done by setting the Don't Fragment (DF) bit in the IP header.
Setting the DF bit implies the use of Path MTU Discovery as described
in [RFC1191], [RFC1981], and [RFC4821]; thus, any TCP implementation
that implements PAWS MUST also implement Path MTU Discovery.
5.8. Duplicates from Earlier Incarnations of Connection
The PAWS mechanism protects against errors due to sequence number
wrap-around on high-speed connections. Segments from an earlier
incarnation of the same connection are also a potential cause of old
duplicate errors. In both cases, the TCP mechanisms to prevent such
errors depend upon the enforcement of an MSL by the Internet (IP)
layer (see the Appendix of RFC 1185 for a detailed discussion).
Unlike the case of sequence space wrap-around, the MSL required to
prevent old duplicate errors from earlier incarnations does not
depend upon the transfer rate. If the IP layer enforces the
recommended 2-minute MSL of TCP, and if the TCP rules are followed,
TCP connections will be safe from earlier incarnations, no matter how
high the network speed. Thus, the PAWS mechanism is not required for
this case.
Borman, et al. Standards Track [Page 26]
RFC 7323 TCP Extensions for High Performance September 2014
We may still ask whether the PAWS mechanism can provide additional
security against old duplicates from earlier connections, allowing us
to relax the enforcement of MSL by the IP layer. Appendix B explores
this question, showing that further assumptions and/or mechanisms are
required, beyond those of PAWS. This is not part of the current
extension.
6. Conclusions and Acknowledgments
This memo presented a set of extensions to TCP to provide efficient
operation over large bandwidth * delay product paths and reliable
operation over very high-speed paths. These extensions are designed
to provide compatible interworking with TCP stacks that do not
implement the extensions.
These mechanisms are implemented using TCP options for scaled windows
and timestamps. The timestamps are used for two distinct mechanisms:
RTTM and PAWS.
The Window Scale option was originally suggested by Mike St. Johns of
USAF/DCA. The present form of the option was suggested by Mike
Karels of UC Berkeley in response to a more cumbersome scheme defined
by Van Jacobson. Lixia Zhang helped formulate the PAWS mechanism
description in [RFC1185].
Finally, much of this work originated as the result of discussions
within the End-to-End Task Force on the theoretical limitations of
transport protocols in general and TCP in particular. Task force
members and others on the end2end-interest list have made valuable
contributions by pointing out flaws in the algorithms and the
documentation. Continued discussion and development since the
publication of [RFC1323] originally occurred in the IETF TCP Large
Windows Working Group, later on in the End-to-End Task Force, and
most recently in the IETF TCP Maintenance Working Group. The authors
are grateful for all these contributions.
7. Security Considerations
The TCP sequence space is a fixed size, and as the window becomes
larger, it becomes easier for an attacker to generate forged packets
that can fall within the TCP window and be accepted as valid
segments. While use of timestamps and PAWS can help to mitigate
this, when using PAWS, if an attacker is able to forge a packet that
is acceptable to the TCP connection, a timestamp that is in the
future would cause valid segments to be dropped due to PAWS checks.
Hence, implementers should take care to not open the TCP window
drastically beyond the requirements of the connection.
Borman, et al. Standards Track [Page 27]
RFC 7323 TCP Extensions for High Performance September 2014
See [RFC5961] for mitigation strategies to blind in-window attacks.
A naive implementation that derives the timestamp clock value
directly from a system uptime clock may unintentionally leak this
information to an attacker. This does not directly compromise any of
the mechanisms described in this document. However, this may be
valuable information to a potential attacker. It is therefore
RECOMMENDED to generate a random, per-connection offset to be used
with the clock source when generating the Timestamps option value
(see Section 5.4). By carefully choosing this random offset, further
improvements as described in [RFC6191] are possible.
Expanding the TCP window beyond 64 KiB for IPv6 allows Jumbograms
[RFC2675] to be used when the local network supports packets larger
than 64 KiB. When larger TCP segments are used, the TCP checksum
becomes weaker.
Mechanisms to protect the TCP header from modification should also
protect the TCP options.
Middleboxes and TCP options:
Some middleboxes have been known to remove the TCP options
described in this document from TCP segments [Honda11].
Middleboxes that remove TCP options described in this document
from the <SYN> segment interfere with the selection of parameters
appropriate for the session. Removing any of these options in a
<SYN,ACK> segment will leave the end hosts in a state that
destroys the proper operation of the protocol.
* If a Window Scale option is removed from a <SYN,ACK> segment,
the end hosts will not negotiate the window scaling factor
correctly. Middleboxes must not remove or modify the Window
Scale option from <SYN,ACK> segments.
* If a stateful firewall uses the window field to detect whether
a received segment is inside the current window, and does not
support the Window Scale option, it will not be able to
correctly determine whether or not a packet is in the window.
These middle boxes must also support the Window Scale option
and apply the scale factor when processing segments. If the
window scale factor cannot be determined, it must not do
window-based processing.
Borman, et al. Standards Track [Page 28]
RFC 7323 TCP Extensions for High Performance September 2014
* If the Timestamps option is removed from the <SYN> or <SYN,ACK>
segments, high speed connections that need PAWS would not have
that protection. Successful negotiation of the Timestamps
option enforces a stricter verification of incoming segments at
the receiver. If the Timestamps option was removed from a
subsequent data segment after a successful negotiation (e.g.,
as part of resegmentation), the segment is discarded by the
receiver without further processing. Middleboxes should not
remove the Timestamps option.
* It must be noted that [RFC1323] doesn't address the case of the
Timestamps option being dropped or selectively omitted after
being negotiated, and that the update in this document may
cause some broken middlebox behavior to be detected
(potentially unresponsive TCP sessions).
Implementations that depend on PAWS could provide a mechanism for the
application to determine whether or not PAWS is in use on the
connection and choose to terminate the connection if that protection
doesn't exist. This is not just to protect the connection against
middleboxes that might remove the Timestamps option, but also against
remote hosts that do not have Timestamp support.
7.1. Privacy Considerations
The TCP options described in this document do not expose individual
user's data. However, a naive implementation simply using the system
clock as a source for the Timestamps option will reveal
characteristics of the TCP, potentially allowing more targeted
attacks. It is therefore RECOMMENDED to generate a random, per-
connection offset to be used with the clock source when generating
the Timestamps option value (see Section 5.4).
Furthermore, the combination, relative ordering, and padding of the
TCP options described in Sections 2.2 and 3.2 will reveal additional
clues to allow the fingerprinting of the system.
8. IANA Considerations
The described TCP options are well known from the superceded
[RFC1323]. IANA has updated the "TCP Option Kind Numbers" table
under "TCP Parameters" to list this document (RFC 7323) as the
reference for "Window Scale" and "Timestamps".
Borman, et al. Standards Track [Page 29]
RFC 7323 TCP Extensions for High Performance September 2014
9. References
9.1. Normative References
[RFC793] Postel, J., "Transmission Control Protocol", STD 7, RFC
793, September 1981.
[RFC1191] Mogul, J. and S. Deering, "Path MTU discovery", RFC 1191,
November 1990.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
9.2. Informative References
[Allman99] Allman, M. and V. Paxson, "On Estimating End-to-End
Network Path Properties", Proceedings of the ACM SIGCOMM
Technical Symposium, Cambridge, MA, September 1999,
<http://aciri.org/mallman/papers/estimation-la.pdf>.
[Floyd05] Floyd, S., "Subject: Re: [tcpm] RFC 1323: Timestamps
option", message to the TCPM mailing list, 26 January
2007, <http://www.ietf.org/mail-archive/web/tcpm/current/
msg02508.html>.
[Garlick77]
Garlick, L., Rom, R., and J. Postel, "Issues in Reliable
Host-to-Host Protocols", Proceedings of the Second
Berkeley Workshop on Distributed Data Management and
Computer Networks, March 1977,
<http://www.rfc-editor.org/ien/ien12.txt>.
[Honda11] Honda, M., Nishida, Y., Raiciu, C., Greenhalgh, A.,
Handley, M., and H. Tokuda, "Is it Still Possible to
Extend TCP?", Proceedings of the ACM Internet Measurement
Conference (IMC) '11, November 2011.
[Jacobson88a]
Jacobson, V., "Congestion Avoidance and Control", SIGCOMM
'88, Stanford, CA, August 1988,
<http://ee.lbl.gov/papers/congavoid.pdf>.
[Jacobson90a]
Jacobson, V., "4BSD Header Prediction", ACM Computer
Communication Review, April 1990.
Borman, et al. Standards Track [Page 30]
RFC 7323 TCP Extensions for High Performance September 2014
[Jacobson90c]
Jacobson, V., "Subject: modified TCP congestion avoidance
algorithm", message to the End2End-Interest mailing list,
30 April 1990, <ftp://ftp.isi.edu/end2end/
end2end-interest-1990.mail>.
[Karn87] Karn, P. and C. Partridge, "Estimating Round-Trip Times in
Reliable Transport Protocols", Proceedings of SIGCOMM '87,
August 1987.
[Kuehlewind10]
Kuehlewind, M. and B. Briscoe, "Chirping for Congestion
Control - Implementation Feasibility", November 2010,
<http://bobbriscoe.net/projects/netsvc_i-f/
chirp_pfldnet10.pdf>.
[Kuzmanovic03]
Kuzmanovic, A. and E. Knightly, "TCP-LP: Low-Priority
Service via End-Point Congestion Control", 2003,
<www.cs.northwestern.edu/~akuzma/doc/TCP-LP-ToN.pdf>.
[Ludwig00] Ludwig, R. and K. Sklower, "The Eifel Retransmission
Timer", ACM SIGCOMM Computer Communication Review Volume
30 Issue 3, July 2000,
<http://ccr.sigcomm.org/archive/2000/july00/
LudwigFinal.pdf>.
[Martin03] Martin, D., "Subject: [Tsvwg] RFC 1323.bis", message to
the TSVWG mailing list, 30 September 2003,
<http://www.ietf.org/mail-archive/web/tsvwg/current/
msg04435.html>.
[Medina04] Medina, A., Allman, M., and S. Floyd, "Measuring
Interactions Between Transport Protocols and Middleboxes",
Proceedings of the ACM SIGCOMM/USENIX Internet Measurement
Conference, October 2004,
<http://www.icir.net/tbit/tbit-Aug2004.pdf>.
[Medina05] Medina, A., Allman, M., and S. Floyd, "Measuring the
Evolution of Transport Protocols in the Internet", ACM
Computer Communication Review Volume 35, No. 2, April
2005,
<http://icir.net/floyd/papers/TCPevolution-Mar2005.pdf>.
Borman, et al. Standards Track [Page 31]
RFC 7323 TCP Extensions for High Performance September 2014
[RE-1323BIS]
Oppermann, A., "Subject: Re: [tcpm] I-D Action: draft-
ietf.tcpm-1323bis-13.txt", message to the TCPM mailing
list, 01 June 2013, <http://www.ietf.org/
mail-archive/web/tcpm/current/msg08001.html>.
[RFC1072] Jacobson, V. and R. Braden, "TCP extensions for long-delay
paths", RFC 1072, October 1988.
[RFC1122] Braden, R., "Requirements for Internet Hosts -
Communication Layers", STD 3, RFC 1122, October 1989.
[RFC1185] Jacobson, V., Braden, B., and L. Zhang, "TCP Extension for
High-Speed Paths", RFC 1185, October 1990.
[RFC1323] Jacobson, V., Braden, B., and D. Borman, "TCP Extensions
for High Performance", RFC 1323, May 1992.
[RFC1981] McCann, J., Deering, S., and J. Mogul, "Path MTU Discovery
for IP version 6", RFC 1981, August 1996.
[RFC2018] Mathis, M., Mahdavi, J., Floyd, S., and A. Romanow, "TCP
Selective Acknowledgment Options", RFC 2018, October 1996.
[RFC2675] Borman, D., Deering, S., and R. Hinden, "IPv6 Jumbograms",
RFC 2675, August 1999.
[RFC2883] Floyd, S., Mahdavi, J., Mathis, M., and M. Podolsky, "An
Extension to the Selective Acknowledgement (SACK) Option
for TCP", RFC 2883, July 2000.
[RFC3522] Ludwig, R. and M. Meyer, "The Eifel Detection Algorithm
for TCP", RFC 3522, April 2003.
[RFC4015] Ludwig, R. and A. Gurtov, "The Eifel Response Algorithm
for TCP", RFC 4015, February 2005.
[RFC4821] Mathis, M. and J. Heffner, "Packetization Layer Path MTU
Discovery", RFC 4821, March 2007.
[RFC4963] Heffner, J., Mathis, M., and B. Chandler, "IPv4 Reassembly
Errors at High Data Rates", RFC 4963, July 2007.
[RFC5681] Allman, M., Paxson, V., and E. Blanton, "TCP Congestion
Control", RFC 5681, September 2009.
Borman, et al. Standards Track [Page 32]
RFC 7323 TCP Extensions for High Performance September 2014
[RFC5961] Ramaiah, A., Stewart, R., and M. Dalal, "Improving TCP's
Robustness to Blind In-Window Attacks", RFC 5961, August
2010.
[RFC6191] Gont, F., "Reducing the TIME-WAIT State Using TCP
Timestamps", BCP 159, RFC 6191, April 2011.
[RFC6298] Paxson, V., Allman, M., Chu, J., and M. Sargent,
"Computing TCP's Retransmission Timer", RFC 6298, June
2011.
[RFC6528] Gont, F. and S. Bellovin, "Defending against Sequence
Number Attacks", RFC 6528, February 2012.
[RFC6675] Blanton, E., Allman, M., Wang, L., Jarvinen, I., Kojo, M.,
and Y. Nishida, "A Conservative Loss Recovery Algorithm
Based on Selective Acknowledgment (SACK) for TCP", RFC
6675, August 2012.
[RFC6691] Borman, D., "TCP Options and Maximum Segment Size (MSS)",
RFC 6691, July 2012.
[RFC6817] Shalunov, S., Hazel, G., Iyengar, J., and M. Kuehlewind,
"Low Extra Delay Background Transport (LEDBAT)", RFC 6817,
December 2012.
Borman, et al. Standards Track [Page 33]
RFC 7323 TCP Extensions for High Performance September 2014
Appendix A. Implementation Suggestions
TCP Option Layout
The following layout is recommended for sending options on
non-<SYN> segments to achieve maximum feasible alignment of 32-bit
and 64-bit machines.
+--------+--------+--------+--------+
| NOP | NOP | TSopt | 10 |
+--------+--------+--------+--------+
| TSval timestamp |
+--------+--------+--------+--------+
| TSecr timestamp |
+--------+--------+--------+--------+
Interaction with the TCP Urgent Pointer
The TCP Urgent Pointer, like the TCP window, is a 16-bit value.
Some of the original discussion for the TCP Window Scale option
included proposals to increase the Urgent Pointer to 32 bits. As
it turns out, this is unnecessary. There are two observations
that should be made:
(1) With IP version 4, the largest amount of TCP data that can be
sent in a single packet is 65495 bytes (64 KiB - 1 - size of
fixed IP and TCP headers).
(2) Updates to the Urgent Pointer while the user is in "urgent
mode" are invisible to the user.
This means that if the Urgent Pointer points beyond the end of the
TCP data in the current segment, then the user will remain in
urgent mode until the next TCP segment arrives. That segment will
update the Urgent Pointer to a new offset, and the user will never
have left urgent mode.
Thus, to properly implement the Urgent Pointer, the sending TCP
only has to check for overflow of the 16-bit Urgent Pointer field
before filling it in. If it does overflow, than a value of 65535
should be inserted into the Urgent Pointer.
The same technique applies to IP version 6, except in the case of
IPv6 Jumbograms. When IPv6 Jumbograms are supported, [RFC2675]
requires additional steps for dealing with the Urgent Pointer;
these steps are described in Section 5.2 of [RFC2675].
Borman, et al. Standards Track [Page 34]
RFC 7323 TCP Extensions for High Performance September 2014
Appendix B. Duplicates from Earlier Connection Incarnations
There are two cases to be considered: (1) a system crashing (and
losing connection state) and restarting, and (2) the same connection
being closed and reopened without a loss of host state. These will
be described in the following two sections.
B.1. System Crash with Loss of State
TCP's quiet time of one MSL upon system startup handles the loss of
connection state in a system crash/restart. For an explanation, see,
for example, "Knowing When to Keep Quiet" in the TCP protocol
specification [RFC793]. The MSL that is required here does not
depend upon the transfer speed. The current TCP MSL of 2 minutes
seemed acceptable as an operational compromise, when many host
systems used to take this long to boot after a crash. Current host
systems can boot considerably faster.
The Timestamps option may be used to ease the MSL requirements (or to
provide additional security against data corruption). If timestamps
are being used and if the timestamp clock can be guaranteed to be
monotonic over a system crash/restart, i.e., if the first value of
the sender's timestamp clock after a crash/restart can be guaranteed
to be greater than the last value before the restart, then a quiet
time is unnecessary.
To dispense totally with the quiet time would require that the host
clock be synchronized to a time source that is stable over the crash/
restart period, with an accuracy of one timestamp clock tick or
better. We can back off from this strict requirement to take
advantage of approximate clock synchronization. Suppose that the
clock is always resynchronized to within N timestamp clock ticks and
that booting (extended with a quiet time, if necessary) takes more
than N ticks. This will guarantee monotonicity of the timestamps,
which can then be used to reject old duplicates even without an
enforced MSL.
B.2. Closing and Reopening a Connection
When a TCP connection is closed, a delay of 2*MSL in TIME-WAIT state
ties up the socket pair for 4 minutes (see Section 3.5 of [RFC793]).
Applications built upon TCP that close one connection and open a new
one (e.g., an FTP data transfer connection using Stream mode) must
choose a new socket pair each time. The TIME-WAIT delay serves two
different purposes:
Borman, et al. Standards Track [Page 35]
RFC 7323 TCP Extensions for High Performance September 2014
(a) Implement the full-duplex reliable close handshake of TCP.
The proper time to delay the final close step is not really
related to the MSL; it depends instead upon the RTO for the FIN
segments and, therefore, upon the RTT of the path. (It could be
argued that the side that is sending a FIN knows what degree of
reliability it needs, and therefore it should be able to
determine the length of the TIME-WAIT delay for the FIN's
recipient. This could be accomplished with an appropriate TCP
option in FIN segments.)
Although there is no formal upper bound on RTT, common network
engineering practice makes an RTT greater than 1 minute very
unlikely. Thus, the 4-minute delay in TIME-WAIT state works
satisfactorily to provide a reliable full-duplex TCP close.
Note again that this is independent of MSL enforcement and
network speed.
The TIME-WAIT state could cause an indirect performance problem
if an application needed to repeatedly close one connection and
open another at a very high frequency, since the number of
available TCP ports on a host is less than 2^16. However, high
network speeds are not the major contributor to this problem;
the RTT is the limiting factor in how quickly connections can be
opened and closed. Therefore, this problem will be no worse at
high transfer speeds.
(b) Allow old duplicate segments to expire.
To replace this function of TIME-WAIT state, a mechanism would
have to operate across connections. PAWS is defined strictly
within a single connection; the last timestamp (TS.Recent) is
kept in the connection control block and discarded when a
connection is closed.
An additional mechanism could be added to the TCP, a per-host
cache of the last timestamp received from any connection. This
value could then be used in the PAWS mechanism to reject old
duplicate segments from earlier incarnations of the connection,
if the timestamp clock can be guaranteed to have ticked at least
once since the old connection was open. This would require that
the TIME-WAIT delay plus the RTT together must be at least one
tick of the sender's timestamp clock. Such an extension is not
part of the proposal of this RFC.
Note that this is a variant on the mechanism proposed by
Garlick, Rom, and Postel [Garlick77], which required each host
to maintain connection records containing the highest sequence
Borman, et al. Standards Track [Page 36]
RFC 7323 TCP Extensions for High Performance September 2014
numbers on every connection. Using timestamps instead, it is
only necessary to keep one quantity per remote host, regardless
of the number of simultaneous connections to that host.
Appendix C. Summary of Notation
The following notation has been used in this document.
Options
WSopt: TCP Window Scale option
TSopt: TCP Timestamps option
Option Fields
shift.cnt: Window scale byte in WSopt
TSval: 32-bit Timestamp Value field in TSopt
TSecr: 32-bit Timestamp Reply field in TSopt
Option Fields in Current Segment
SEG.TSval: TSval field from TSopt in current segment
SEG.TSecr: TSecr field from TSopt in current segment
SEG.WSopt: 8-bit value in WSopt
Clock Values
my.TSclock: System-wide source of 32-bit timestamp values
my.TSclock.rate: Period of my.TSclock (1 ms to 1 sec)
Snd.TSoffset: An offset for randomizing Snd.TSclock
Snd.TSclock: my.TSclock + Snd.TSoffset
Per-Connection State Variables
TS.Recent: Latest received Timestamp
Last.ACK.sent: Last ACK field sent
Snd.TS.OK: 1-bit flag
Snd.WS.OK: 1-bit flag
Rcv.Wind.Shift: Receive window scale exponent
Snd.Wind.Shift: Send window scale exponent
Start.Time: Snd.TSclock value when the segment being timed
was sent (used by code from before RFC 1323).
Procedure
Update_SRTT(m) Procedure to update the smoothed RTT and RTT
variance estimates, using the rules of
[Jacobson88a], given m, a new RTT measurement
Borman, et al. Standards Track [Page 37]
RFC 7323 TCP Extensions for High Performance September 2014
Send Sequence Variables
SND.UNA: Send unacknowledged
SND.NXT: Send next
SND.WND: Send window
ISS: Initial send sequence number
Receive Sequence Variables
RCV.NXT: Receive next
RCV.WND: Receive window
IRS: Initial receive sequence number
Appendix D. Event Processing Summary
This appendix attempts to specify the algorithms unambiguously by
presenting modifications to the Event Processing rules in Section 3.9
of RFC 793. The change bars ("|") indicate lines that are different
from RFC 793.
OPEN Call
...
An initial send sequence number (ISS) is selected. Send a <SYN>
| segment of the form:
|
| <SEQ=ISS><CTL=SYN><TSval=Snd.TSclock><WSopt=Rcv.Wind.Shift>
...
SEND Call
CLOSED STATE (i.e., TCB does not exist)
...
LISTEN STATE
If active and the foreign socket is specified, then change the
connection from passive to active, select an ISS. Send a SYN
| segment containing the options: <TSval=Snd.TSclock> and
| <WSopt=Rcv.Wind.Shift>. Set SND.UNA to ISS, SND.NXT to ISS+1.
Enter SYN-SENT state. ...
SYN-SENT STATE
SYN-RECEIVED STATE
Borman, et al. Standards Track [Page 38]
RFC 7323 TCP Extensions for High Performance September 2014
...
ESTABLISHED STATE
CLOSE-WAIT STATE
Segmentize the buffer and send it with a piggybacked
acknowledgment (acknowledgment value = RCV.NXT). ...
If the urgent flag is set ...
| If the Snd.TS.OK flag is set, then include the TCP Timestamps
| option <TSval=Snd.TSclock,TSecr=TS.Recent> in each data
| segment.
|
| Scale the receive window for transmission in the segment
| header:
|
| SEG.WND = (RCV.WND >> Rcv.Wind.Shift).
SEGMENT ARRIVES
...
If the state is LISTEN then
first check for an RST
...
second check for an ACK
...
third check for a SYN
If the SYN bit is set, check the security. If the ...
...
If the SEG.PRC is less than the TCB.PRC then continue.
| Check for a Window Scale option (WSopt); if one is found,
| save SEG.WSopt in Snd.Wind.Shift and set Snd.WS.OK flag on.
| Otherwise, set both Snd.Wind.Shift and Rcv.Wind.Shift to
| zero and clear Snd.WS.OK flag.
|
| Check for a TSopt option; if one is found, save SEG.TSval in
| the variable TS.Recent and turn on the Snd.TS.OK bit.
Borman, et al. Standards Track [Page 39]
RFC 7323 TCP Extensions for High Performance September 2014
Set RCV.NXT to SEG.SEQ+1, IRS is set to SEG.SEQ and any
other control or text should be queued for processing later.
ISS should be selected and a SYN segment sent of the form:
<SEQ=ISS><ACK=RCV.NXT><CTL=SYN,ACK>
| If the Snd.WS.OK bit is on, include a WSopt
| <WSopt=Rcv.Wind.Shift> in this segment. If the Snd.TS.OK
| bit is on, include a TSopt <TSval=Snd.TSclock,
| TSecr=TS.Recent> in this segment. Last.ACK.sent is set to
| RCV.NXT.
SND.NXT is set to ISS+1 and SND.UNA to ISS. The connection
state should be changed to SYN-RECEIVED. Note that any
other incoming control or data (combined with SYN) will be
processed in the SYN-RECEIVED state, but processing of SYN
and ACK should not be repeated. If the listen was not fully
specified (i.e., the foreign socket was not fully
specified), then the unspecified fields should be filled in
now.
fourth other text or control
...
If the state is SYN-SENT then
first check the ACK bit
...
...
fourth check the SYN bit
...
If the SYN bit is on and the security/compartment and
precedence are acceptable then, RCV.NXT is set to SEG.SEQ+1,
IRS is set to SEG.SEQ. SND.UNA should be advanced to equal
SEG.ACK (if there is an ACK), and any segments on the
retransmission queue which are thereby acknowledged should
be removed.
| Check for a Window Scale option (WSopt); if it is found,
| save SEG.WSopt in Snd.Wind.Shift; otherwise, set both
| Snd.Wind.Shift and Rcv.Wind.Shift to zero.
|
Borman, et al. Standards Track [Page 40]
RFC 7323 TCP Extensions for High Performance September 2014
| Check for a TSopt option; if one is found, save SEG.TSval in
| variable TS.Recent and turn on the Snd.TS.OK bit in the
| connection control block. If the ACK bit is set, use
| Snd.TSclock - SEG.TSecr as the initial RTT estimate.
If SND.UNA > ISS (our SYN has been ACKed), change the
connection state to ESTABLISHED, form an <ACK> segment:
<SEQ=SND.NXT><ACK=RCV.NXT><CTL=ACK>
| and send it. If the Snd.TS.OK bit is on, include a TSopt
| option <TSval=Snd.TSclock,TSecr=TS.Recent> in this <ACK>
| segment. Last.ACK.sent is set to RCV.NXT.
Data or controls that were queued for transmission may be
included. If there are other controls or text in the
segment, then continue processing at the sixth step below
where the URG bit is checked; otherwise, return.
Otherwise, enter SYN-RECEIVED, form a <SYN,ACK> segment:
<SEQ=ISS><ACK=RCV.NXT><CTL=SYN,ACK>
| and send it. If the Snd.TS.OK bit is on, include a TSopt
| option <TSval=Snd.TSclock,TSecr=TS.Recent> in this segment.
| If the Snd.WS.OK bit is on, include a WSopt option
| <WSopt=Rcv.Wind.Shift> in this segment. Last.ACK.sent is
| set to RCV.NXT.
If there are other controls or text in the segment, queue
them for processing after the ESTABLISHED state has been
reached, return.
fifth, if neither of the SYN or RST bits is set then drop the
segment and return.
Otherwise
first check the sequence number
SYN-RECEIVED STATE
ESTABLISHED STATE
FIN-WAIT-1 STATE
FIN-WAIT-2 STATE
CLOSE-WAIT STATE
CLOSING STATE
LAST-ACK STATE
TIME-WAIT STATE
Borman, et al. Standards Track [Page 41]
RFC 7323 TCP Extensions for High Performance September 2014
Segments are processed in sequence. Initial tests on
arrival are used to discard old duplicates, but further
processing is done in SEG.SEQ order. If a segment's
contents straddle the boundary between old and new, only the
new parts should be processed.
| Rescale the received window field:
|
| TrueWindow = SEG.WND << Snd.Wind.Shift,
|
| and use "TrueWindow" in place of SEG.WND in the following
| steps.
|
| Check whether the segment contains a Timestamps option and
| if bit Snd.TS.OK is on. If so:
|
| If SEG.TSval < TS.Recent and the RST bit is off:
|
| If the connection has been idle more than 24 days,
| save SEG.TSval in variable TS.Recent, else the segment
| is not acceptable; follow the steps below for an
| unacceptable segment.
|
| If SEG.TSval >= TS.Recent and SEG.SEQ <= Last.ACK.sent,
| then save SEG.TSval in variable TS.Recent.
There are four cases for the acceptability test for an
incoming segment:
...
If an incoming segment is not acceptable, an acknowledgment
should be sent in reply (unless the RST bit is set; if so
drop the segment and return):
<SEQ=SND.NXT><ACK=RCV.NXT><CTL=ACK>
| Last.ACK.sent is set to SEG.ACK of the acknowledgment. If
| the Snd.TS.OK bit is on, include the Timestamps option
| <TSval=Snd.TSclock,TSecr=TS.Recent> in this <ACK> segment.
Set Last.ACK.sent to SEG.ACK and send the <ACK> segment.
After sending the acknowledgment, drop the unacceptable
segment and return.
...
Borman, et al. Standards Track [Page 42]
RFC 7323 TCP Extensions for High Performance September 2014
fifth check the ACK field,
if the ACK bit is off drop the segment and return
if the ACK bit is on
...
ESTABLISHED STATE
If SND.UNA < SEG.ACK <= SND.NXT then, set SND.UNA <-
| SEG.ACK. Also compute a new estimate of round-trip time.
| If Snd.TS.OK bit is on, use Snd.TSclock - SEG.TSecr;
| otherwise, use the elapsed time since the first segment
| in the retransmission queue was sent. Any segments on
the retransmission queue that are thereby entirely
acknowledged...
...
seventh, process the segment text,
ESTABLISHED STATE
FIN-WAIT-1 STATE
FIN-WAIT-2 STATE
...
Send an acknowledgment of the form:
<SEQ=SND.NXT><ACK=RCV.NXT><CTL=ACK>
| If the Snd.TS.OK bit is on, include the Timestamps option
| <TSval=Snd.TSclock,TSecr=TS.Recent> in this <ACK> segment.
| Set Last.ACK.sent to SEG.ACK of the acknowledgment, and send
| it. This acknowledgment should be piggybacked on a segment
being transmitted if possible without incurring undue delay.
...
Borman, et al. Standards Track [Page 43]
RFC 7323 TCP Extensions for High Performance September 2014
Appendix E. Timestamps Edge Cases
While the rules laid out for when to calculate RTTM produce the
correct results most of the time, there are some edge cases where an
incorrect RTTM can be calculated. All of these situations involve
the loss of segments. It is felt that these scenarios are rare, and
that if they should happen, they will cause a single RTTM measurement
to be inflated, which mitigates its effects on RTO calculations.
[Martin03] cites two similar cases when the returning <ACK> is lost,
and before the retransmission timer fires, another returning <ACK>
segment arrives, which acknowledges the data. In this case, the RTTM
calculated will be inflated:
clock
tc=1 <A, TSval=1> ------------------->
tc=2 (lost) <---- <ACK(A), TSecr=1, win=n>
(RTTM would have been 1)
(receive window opens, window update is sent)
tc=5 <---- <ACK(A), TSecr=1, win=m>
(RTTM is calculated at 4)
One thing to note about this situation is that it is somewhat bounded
by RTO + RTT, limiting how far off the RTTM calculation will be.
While more complex scenarios can be constructed that produce larger
inflations (e.g., retransmissions are lost), those scenarios involve
multiple segment losses, and the connection will have other more
serious operational problems than using an inflated RTTM in the RTO
calculation.
Appendix F. Window Retraction Example
Consider an established TCP connection using a scale factor of 128,
Snd.Wind.Shift=7 and Rcv.Wind.Shift=7, that is running with a very
small window because the receiver is bottlenecked and both ends are
doing small reads and writes.
Consider the ACKs coming back:
SEG.ACK SEG.WIN computed SND.WIN receiver's actual window
1000 2 1256 1300
The sender writes 40 bytes and receiver ACKs:
1040 2 1296 1300
Borman, et al. Standards Track [Page 44]
RFC 7323 TCP Extensions for High Performance September 2014
The sender writes 5 additional bytes and the receiver has a problem.
Two choices:
1045 2 1301 1300 - BEYOND BUFFER
1045 1 1173 1300 - RETRACTED WINDOW
This is a general problem and can happen any time the sender does a
write, which is smaller than the window scale factor.
In most stacks, it is at least partially obscured when the window
size is larger than some small number of segments because the stacks
prefer to announce windows that are an integral number of segments,
rounded up to the next scale factor. This plus silly window
suppression tends to cause less frequent, larger window updates. If
the window was rounded down to a segment size, there is more
opportunity to advance the window, the BEYOND BUFFER case above,
rather than retracting it.
Appendix G. RTO Calculation Modification
Taking multiple RTT samples per window would shorten the history
calculated by the RTO mechanism in [RFC6298], and the below algorithm
aims to maintain a similar history as originally intended by
[RFC6298].
It is roughly known how many samples a congestion window worth of
data will yield, not accounting for ACK compression, and ACK losses.
Such events will result in more history of the path being reflected
in the final value for RTO, and are uncritical. This modification
will ensure that a similar amount of time is taken into account for
the RTO estimation, regardless of how many samples are taken per
window:
ExpectedSamples = ceiling(FlightSize / (SMSS * 2))
alpha' = alpha / ExpectedSamples
beta' = beta / ExpectedSamples
Note that the factor 2 in ExpectedSamples is due to "Delayed ACKs".
Borman, et al. Standards Track [Page 45]
RFC 7323 TCP Extensions for High Performance September 2014
Instead of using alpha and beta in the algorithm of [RFC6298], use
alpha' and beta' instead:
RTTVAR <- (1 - beta') * RTTVAR + beta' * |SRTT - R'|
SRTT <- (1 - alpha') * SRTT + alpha' * R'
(for each sample R')
Appendix H. Changes from RFC 1323
Several important updates and clarifications to the specification in
RFC 1323 are made in this document. The technical changes are
summarized below:
(a) A wrong reference to SND.WND was corrected to SEG.WND in
Section 2.3.
(b) Section 2.4 was added describing the unavoidable window
retraction issue and explicitly describing the mitigation steps
necessary.
(c) In Section 3.2, the wording how the Timestamps option
negotiation is to be performed was updated with RFC2119 wording.
Further, a number of paragraphs were added to clarify the
expected behavior with a compliant implementation using TSopt,
as RFC 1323 left room for interpretation -- e.g., potential late
enablement of TSopt.
(d) The description of which TSecr values can be used to update the
measured RTT has been clarified. Specifically, with timestamps,
the Karn algorithm [Karn87] is disabled. The Karn algorithm
disables all RTT measurements during retransmission, since it is
ambiguous whether the <ACK> is for the original segment, or the
retransmitted segment. With timestamps, that ambiguity is
removed since the TSecr in the <ACK> will contain the TSval from
whichever data segment made it to the destination.
(e) RTTM update processing explicitly excludes segments not updating
SND.UNA. The original text could be interpreted to allow taking
RTT samples when SACK acknowledges some new, non-continuous
data.
Borman, et al. Standards Track [Page 46]
RFC 7323 TCP Extensions for High Performance September 2014
(f) In RFC 1323, Section 3.4, step (2) of the algorithm to control
which timestamp is echoed was incorrect in two regards:
(1) It failed to update TS.Recent for a retransmitted segment
that resulted from a lost <ACK>.
(2) It failed if SEG.LEN = 0.
In the new algorithm, the case of SEG.TSval >= TS.Recent is
included for consistency with the PAWS test.
(g) It is now recommended that the Timestamps option is included in
<RST> segments if the incoming segment contained a Timestamps
option.
(h) <RST> segments are explicitly excluded from PAWS processing.
(i) Added text to clarify the precedence between regular TCP
[RFC793] and this document's Timestamps option / PAWS
processing. Discussion about combined acceptability checks are
ongoing.
(j) Snd.TSoffset and Snd.TSclock variables have been added.
Snd.TSclock is the sum of my.TSclock and Snd.TSoffset. This
allows the starting points for timestamp values to be randomized
on a per-connection basis. Setting Snd.TSoffset to zero yields
the same results as [RFC1323]. Text was added to guide
implementers to the proper selection of these offsets, as
entirely random offsets for each new connection will conflict
with PAWS.
(k) Appendix A has been expanded with information about the TCP
Urgent Pointer. An earlier revision contained text around the
TCP MSS option, which was split off into [RFC6691].
(l) One correction was made to the Event Processing Summary in
Appendix D. In SEND CALL/ESTABLISHED STATE, RCV.WND is used to
fill in the SEG.WND value, not SND.WND.
(m) Appendix G was added to exemplify how an RTO calculation might
be updated to properly take the much higher RTT sampling
frequency enabled by the Timestamps option into account.
Borman, et al. Standards Track [Page 47]
RFC 7323 TCP Extensions for High Performance September 2014
Editorial changes to the document, that don't impact the
implementation or function of the mechanisms described in this
document, include:
(a) Removed much of the discussion in Section 1 to streamline the
document. However, detailed examples and discussions in
Sections 2, 3, and 5 are kept as guidelines for implementers.
(b) Added short text that the use of WS increases the chances of
sequence number wrap, thus the PAWS mechanism is required in
certain environments.
(c) Removed references to "new" options, as the options were
introduced in [RFC1323] already. Changed the text in
Section 1.3 to specifically address TS and WS options.
(d) Section 1.4 was added for [RFC2119] wording. Normative text was
updated with the appropriate phrases.
(e) Added < > brackets to mark specific types of segments, and
replaced most occurrences of "packet" with "segment", where TCP
segments are referred to.
(f) Updated the text in Section 3 to take into account what has been
learned since [RFC1323].
(g) Removed some unused references.
(h) Removed the list of changes between [RFC1323] and prior
versions. These changes are mentioned in Appendix C of
[RFC1323].
(i) Moved "Changes from RFC 1323" to the end of the appendices for
easier lookup. In addition, the entries were split into a
technical and an editorial part, and sorted to roughly
correspond with the sections in the text where they apply.
Borman, et al. Standards Track [Page 48]
RFC 7323 TCP Extensions for High Performance September 2014
Authors' Addresses
David Borman
Quantum Corporation
Mendota Heights, MN 55120
USA
EMail: david.borman@quantum.com
Bob Braden
University of Southern California
4676 Admiralty Way
Marina del Rey, CA 90292
USA
EMail: braden@isi.edu
Van Jacobson
Google, Inc.
1600 Amphitheatre Parkway
Mountain View, CA 94043
USA
EMail: vanj@google.com
Richard Scheffenegger (editor)
NetApp, Inc.
Am Euro Platz 2
Vienna, 1120
Austria
EMail: rs@netapp.com
Borman, et al. Standards Track [Page 49]